Plasma modification of ZnMgAl-LDHs for adsorption property improvement

Highly selective and efficient Pb2+ capture using PO4-loaded 3D-NiFe layer double hydroxides derived from MIL-88A

Lead (Pb) contamination in water requires improved decontamination technologies. The addition of phosphate to precipitate Pb2+ is a widely used method for remediating Pb in soil and water, though it has certain limitations. This study focuses on novel 3D mesoporous layered double hydroxide (LDH) sorbents functionalized with phosphate anions for Pb2+ removal from contaminated waters. Our innovative strategy involves converting a sacrificial template metal-organic frameworks (MOFs) structure (MIL-88A(Fe)) into NixFe LDH, followed by an anion exchange reaction with phosphate anions. This process preserves the 3D microrod architecture of MIL-88A and prevents deleterious LDH particle aggregation. The synthesis results in stable microrod crystals, 1-2 μm long, composed of 3D assemblies of NixFe-PO4 LDH nanoplatelets with a specific surface area exceeding 110 m2/g. The novel LDH materials display fast adsorption kinetics (pseudo-second order model) and remarkably high Pb2+ removal performances (Langmuir isotherm model) with a capacity of 538 mg/g, surpassing other reported adsorbents. LDH-PO4 exhibits high selectivity for Pb2+ over competing ions like Ni2+ and Cd2+ (selectivity order is: Pb2+ > Ni2+ > Cd2+). Removal of Pb2+ from NixFeLDH/88A-PO4 involves various mechanisms, including surface complexation and surface precipitation of lead phosphate or lead hydroxide phases as revealed by structural characterization techniques.

Textural properties and adsorption behavior of Zn-Mg-Al layered double hydroxide upon crystal violet dye removal as a low cost, effective, and recyclable adsorbent

The preparation of adsorbents plays a vital role in the adsorption method. In particular, many adsorbents with high specific surface areas and unique shapes are essential for the adsorption strategy. A Zn-Mg-Al/layer double hydroxide (LDH) was designed in this study using a simple co-precipitation process. Adsorbent based on Zn-Mg-Al/LDH was used to remove crystal violet (CV) from the wastewater. The impacts of the initial dye concentration, pH, and temperature on CV adsorption performance were systematically examined. The adsorbents were analyzed both before and after adsorption using FTIR, XRD, and SEM. The roughness parameters and surface morphologies of the produced LDH were estimated using 3D SEM images. Under the best conditions (dose of adsorbent = 0.07 g and pH = 9), the maximum adsorption capacity has been achieved. Adsorption kinetics studies revealed that the reaction that led to the adsorption of CV dye onto Zn-Mg-Al/LDH was a pseudo-second-order model. Additionally, intraparticle diffusion suggests that Zn-Mg-Al/LDH has a fast diffusion constant for CV molecules (0.251 mg/(g min^1/2)). Furthermore, as predicted by the Langmuir model, the maximal Zn-Mg-Al/LDH adsorption capacity of CV was 64.80 mg/g. The CV dimensionless separation factor (R_L) onto Zn-Mg-Al/LDH was 0.769, indicating that adsorption was favorable. The effect of temperature was performed at 25, 35, and 45 °C in order to establish the thermodynamic parameters ∆H^o, ∆S^o, and ∆G^o. The computed values indicated exothermic and spontaneous adsorption processes. The study presented here might be used to develop new adsorbents with enhanced adsorption capabilities for the purpose of protecting the water environment.

Application of functionalized layered double hydroxides for heavy metal removal: A review

Layered double hydroxides (LDHs) are ionic laminar composites composed of positively charged brucite-like layers with an interlayered region containing charged compensating anions and solvation molecules. Such functional LDHs materials present a strong potential for heavy metal treatment especially for wastewater and soil, due to the large surface area and layered structure. This paper started with the background of techniques for heavy metals treatment and then discussed the potential environmental toxic effects, feasibility, stability of LDH composites. The preparation strategies of LDHs composites, and their application were summarized, followed by main mechanisms involving chelation, complexation, surface precipitation, ion exchange. This work also presented the potential environmental toxic effects, feasibility, stability of LDHs composites, reuse of waste liquid and the ratio adjustment of M²⁺ and N³⁺ for LDHs synthesis. While most efforts focused on improving the absorption capacity of LDHs by composites construction, ignoring the toxicity effects and detailed mechanism investigation. Based on a thorough review of the latest development, the challenges and perspectives would be proposed, offering promising insights on environmental purification via LDHs based materials.

Enhanced adsorption properties of organic ZnCr-LDH synthesized by soft template method for anionic dyes

Organic ZnCr-LDH (ST-LDH) was synthesized by a facile one-step hydrothermal technique using methyl orange (MO) as a soft template agent, which can efficiently remove methyl orange (MO), Congo red (CR), and orange II (OII) from aqueous solution. The microstructure of ST-LDH by modifying changed obviously, from the cellular structure to the stacking structure formed by the face-face contact of hydrotalcite nanosheets, which resulted in much more exchangeable nitrate ions to remain in the interlayer space. The pre-insertion of benzene sulfonate as a pillar expanded the interlayer gallery, which facilitated the pollutant anions (MO, CR, and OII) into the interlayer of LDH in the subsequent adsorption process. The maximum adsorption capacity of ST-LDH for MO, CR, and OII was 4200.8 mg/g, 1252.0 mg/g, and 1670.6 mg/g, respectively, which is approximately 1.86 times, 1.8 times, and 2.32 times that of the pristine NO₃-LDH, respectively. The removal mechanism of anionic dyes was determined as anion exchange between NO₃^- anions and dye molecules. The adsorption behavior for MO and OII is multilayer adsorption, while the adsorption behavior for CR is monolayer adsorption. The adsorption process mainly was controlled by the chemical bonding between the dye molecules and adsorbent active sites. The LDH can be effectively regenerated by photocatalysis after MO adsorption. The ST-LDH has a great potential to be used as a high-efficient adsorbent to remove anionic dyes from aqueous solution. The schematic illustration of the synthetic process of soft template agent modified and unmodified hydrotalcites by one-pot hydrothermal method and the adsorption process of MO by ST-LDH were shown in Fig. 12. Modified hydrotalcite (ST-LDH) was prepared using methyl orange (MO) as a soft template agent. Compared with unmodified hydrotalcite (NO₃-LDH), the insertion of benzene sulfonate anions into the hydrotalcite layer resulted in the increase of the interlayer spacing from 8.269 to 8.654Å. The LDH host structure pre-intercalated by benzene sulfonate anions evolved into pillared materials in interlayer; benzene sulfonate anions as a column expanded the interlayer spacing of (003) base plane, which facilitated the pollutant anions (MO, CR, and OII) into the interlayer of ST-LDH and exchanged with NO₃^- anion in the subsequent adsorption process. It can be inferred that in the process of modification hydrotalcite by benzene sulfonate, a small amount of benzene sulfonate anions pre-inserted into the gallery of hydrotalcite with a monolayer model in the process of hydrotalcite modification, and its inclination angle is calculated to be about 29.1°. After ST-LDH sample adsorbed the MO molecules, dye molecules intercalated into the LDH host, and successful exchange with NO₃^- anions, the d₀₀₃ value increased to 24.78 Å. A large amount of MO^- anions were intercalated into the gallery of ST-LDH with a bilayer model according to the Freundlich isotherm model, and the tilting angle increases to 53.6°. The adsorption capacity of MO by ST-LDH was significantly enhanced to 4200.8 mg/g, which was much higher than that of NO₃-LDH (2252.8 mg/g). Schematic illustration of the synthetic process of LDH materials and adsorption process of MO by ST-LDH.

Synergistic adsorption-photocatalytic degradation of different antibiotics in seawater by a porous g-C3N4/calcined-LDH and its application in synthetic mariculture wastewater

In this work, a modified g-C₃N₄/MgZnAl-calcined layered double hydroxide composite (M-CN/cLDH) was successfully fabricated via a template method. The composite material is a hierarchical porous flower-like nanostructure self-assembled from stacked hybrid flakes. The 3D M-CN/cLDH architectures exhibit a synergistic effect of adsorption and photocatalysis for eliminating typical tetracycline antibiotics in seawater, i.e., oxytetracycline (OTC), tetracycline (TC), chlortetracycline (CTC), and doxycycline (DXC). The synergistic removal rate of OTC in seawater of M-CN/cLDH is 2.73 times higher than that of g-C₃N₄ after 120 min of visible-light illumination, and M-CN/cLDH also performs better adsorption-photocatalytic degradation on OTC in the continuous flow reaction process. The superior adsorption capability of the M-CN/cLDH is attributed to the open porous structures of cLDH, and its excellent photocatalytic degradation activity is ascribed to the closely bonded heterojunctions between g-C₃N₄ (CN) and cLDH double layers. The mass spectra reveals the degradation pathways of OTC, and its byproducts are less toxic after degradation for 120 min. The exploration of the M-CN/cLDH in synthetic mariculture wastewater suggested a huge potential for its practical application. With the assistance of magnesium ammonium phosphate (MAP) precipitation pretreatment, the material can effectively retain the high OTC removal rate in the synthetic mariculture wastewater circumstance.

In situ preparation of highly dispersed Pd supported on exfoliated layered double hydroxides via nitrogen plasma for 4-nitrophenol reduction

In this work, a simple and environmental-friendly nitrogen glow discharge plasma reduction method has been developed for synthesizing palladium nanoparticles (PdNPs) supported on exfoliated Mg-Al-layered double hydroxide (Pd/LDH) catalysts. The as-prepared catalysts were characterized by means of characterizations methods, which contain X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectrometry (XPS), and Fourier transform infrared (FT-IR). Highly dispersed ultrafine PdNPs were supported on exfoliated, defect-induced LDHs uniformly without agglomeration. The effects of treatment time of nitrogen plasma and Pd loading amount on structure, morphology, and catalytic performance of Pd/LDHs were investigated. The comparisons of structure and morphology between LDHs and Pd/LDHs were also discussed. The average particle size of as-synthesized PdNPs with face-centered cubic structure is 2.01 nm, which ranges from 1.18 to 3.01 nm. Nitrogen plasma cannot only reduce Pd²⁺, but also exfoliate LDHs, introduce defects, and even destroy the structure of LDHs. The Pd/LDH catalyst with 1 wt% Pd loading under nitrogen plasma treatment for 60 min showed the best catalytic performance in 4-nitrophenol reduction. The turnover frequency (TOF) of as-prepared catalyst is 20-fold higher than that of commercial Pd/C catalyst.

Facile synthesis of superhydrophobic three-metal-component layered double hydroxide films on aluminum foils for highly improved corrosion inhibition

A simple hydrothermal method was presented to obtain various superhydrophobic ZnMgAl layered double hydroxide films on aluminum foils (AF) with excellent corrosion inhibition.