Dynamic surface properties of poly(methylalkyldiallylammonium chloride) solutions

Studying surfactant mass transport through dynamic interfacial tension measurements: A review of the models, experiments, and the contribution of microfluidics

Surfactant mass transport towards an interface plays a critical role during formation of emulsions, foams and in industrial processes where two immiscible phases coexist. The understanding of these mechanisms as experimentally observed by dynamic interfacial tension measurements, is crucial. In this review, theoretical models describing both equilibrated systems and surfactant kinetics are covered. Experimental results from the literature are analysed based on the nature of surfactants and the tensiometry methods used. The innovative microfluidic techniques that have become available to study both diffusion and adsorption mechanisms during surfactant mass transport are discussed and compared with classical methods. This review focuses on surfactant transport during formation of droplets or bubbles; stabilisation of dispersed systems is not discussed here.

Synthesis and Demulsification Properties of Poly (DMDAAC-co-DAMBAC) (9:1) Copolymer

Utilizing the copolymerization modification of dimethyl diallyl ammonium chloride (DMDAAC), the high positive charge density of the copolymer could be maintained, thereby facilitating the deficiency of its monomer in the application. In this paper, poly (DMDAAC-co-DAMBAC) (9:1) was synthesized with an aqueous polymerization method using DMDAAC and methyl benzyl diallyl ammonium chloride (DAMBAC) as monomers and 2,2'-azobis [2-methylpropionamidine] dihydrochloride (V50) as an initiator. Targeted to the product's weight-average relative molecular mass (M_w), the response surface methodology (RSM) was used to optimize the preparation process. The optimal process conditions were obtained as follows: w (M) = 80.0%, m (V50):m (M) = 0.00700%, m (Na₄EDTA):m (M) = 0.00350%, T₁ = 50.0 °C, T₂ = 60.0 °C, and T₃ = 72.5 °C. The intrinsic viscosity ([η]) of the product was 1.780 dL/g, and the corresponding double bond conversion (Conv.) was 90.25 %. Poly (DMDAAC-co-DAMBAC) (9:1) revealed a highest M_w of 5.637 × 10⁵, together with the polydispersity index d (M_w/M_n) as 1.464. For the demulsification performance of simulated crude oil O/W emulsions, the demulsification rate of poly (DMDAAC-co-DAMBAC) (9:1) could reach 97.73%. Our study has illustrated that the copolymerization of DMDAAC and a small amount of DAMBAC with poor reactivity could significantly improve the relative molecular weight of the polymer, enhance its lipophilicity, and thus the application scope of the polymer.

Effect of Substituents on the Homopolymerization Activity of Methyl Alkyl Diallyl Ammonium Chloride

Among nitrogen-containing cationic electrolytes, diallyl quaternary ammonium salt is a typical monomer with the highest positive charge density, which has attracted the most attention, especially in the research on homopolymers and copolymers of dimethyl diallyl ammonium chloride (DMDAAC), which occupy a very unique and important position. In order to improve the lipophilicity of substituted diallyl ammonium chloride monomers under the premise of high cationic charge density, the simplest, most direct, and most efficient structure design strategy was selected in this paper. Only one of the substituents on DMDAAC quaternary ammonium nitrogen was modified by alkyl; the substituents were propyl and amyl groups, and their corresponding monomers were methyl propyl diallyl ammonium chloride (MPDAAC) and methyl amyl diallyl ammonium chloride (MADAAC), respectively. The effect of substituent structure on the homopolymerization activity of methyl alkyl diallyl ammonium chloride was illustrated by quantum chemical calculation and homopolymerization rate determination experiments via ammonium persulfate (APS) as the initiator system. The results of quantum chemistry simulation showed that, with the finite increase in substituted alkyl chain length, the numerical values of the bond length and the charge distribution of methyl alkyl diallyl ammonium chloride monomer changed little, with the activation energy of the reactions in the following order: DMDAAC < MPDAAC < MADAAC. The polymerization activities measured by the dilatometer method were in the order DMDAAC > MPDAAC > MADAAC. The activation energies Ea of homopolymerization were 96.70 kJ/mol, 97.25 kJ/mol, and 100.23 kJ/mol, and the rate equation of homopolymerization of each monomer was obtained. After analyzing and comparing these results, it could be easily found that the electronic effect of substituent was not obvious, whereas the effect of the steric hindrance was dominant. The above studies have laid a good foundation for an understanding of the polymerization activity of methyl alkyl diallyl ammonium chloride monomers and the possibility of preparation and application of these polymers with high molecular weight.

Network Formation of DNA/Polyelectrolyte Fibrous Aggregates Adsorbed at the Water-Air Interface

It is discovered that complexes of DNA and hydrophobically modified polyelectrolytes form a rigid network of threadlike or fibrous aggregates at the liquid-gas interface whose morphology can dramatically affect the mechanical properties. While mixed solutions of DNA and poly(N,N-diallyl-N,N-dimethylammonium chloride) (PDADMAC) exhibit no notable surface activity, the complexes formed from DNA with poly(N,N-diallyl-N-butyl-N-methylammonium chloride) are surface-active, in contrast to either of the separate components. Further, complexes of DNA and poly(N,N-diallyl-N-hexyl-N-methylammonium chloride) (PDAHMAC) with its longer hydrophobic side chains exhibit pronounced surface activity with values of surface pressures up to 16 mN/m and dynamic surface elasticity up to 58 mN/m. If the PDAHMAC nitrogen to DNA phosphate molar ratio, N/P, is between 0.6 and 3, abrupt compression of the adsorption layer leads unexpectedly to a noticeable decrease of the surface elasticity. The application of imaging techniques reveals that this effect is a consequence of the destruction of a rigid network of threadlike DNA/polyelectrolyte aggregates at the interface. The toroidal aggregates, which are typical for the bulk phase of DNA/PDADMAC solutions in this range of N/P ratios, are not observed in the surface layer. The observed link between the mechanical properties and interfacial morphology of surface-active complexes formed from DNA with hydrophobically modified polyelectrolytes indicates that tuning polyelectrolyte hydrophobicity in these systems may be a means to develop their use in applications ranging from nonviral gene-delivery vehicles to conductive nanowires.