Efficient and rapid adsorption of iodide ion from aqueous solution by porous silica spheres loaded with calcined Mg-Al layered double hydroxide

Simple and scalable preparation of lignin based porous carbon coated nano-clay composites and their efficient removal for the diversified iodine

Here, lignin and nano-clay were used to prepare novel composite adsorbents by one-step carbonization without adding activators for radioactive iodine capture. Specially, 1D nano-clay such as halloysite (Hal), palygorskite (Pal) and sepiolite (Sep) were selected as skeleton components, respectively, enzymatic hydrolysis lignin (EHL) as carbon source, lignin based porous carbon/nano-clay composites (ELC-X) were prepared through ultrasonic impregnation, freeze drying, and carbonization. Characterization results indicated lignin based porous carbon (ELC) well coated on the surface of nano-clay, and made its surface areas increase to 252 m2/g. These composites appeared the micro-mesoporous hierarchical structure, considerable N doping and good chemical stability. Results of adsorption experiments showed that the introduction of ELC could well promote iodine vapor uptake of nano-clay, and up to 435.0 mg/g. Meanwhile, the synergistic effect between lignin based carbon and nano-clay was very significant for the adsorption of iodine/n-hexane and iodine ions, their capacity were far exceed those of a single material, respectively. The relevant adsorption kinetic and thermodynamics, and mechanism of ELC-X composites were clarified. This work provided a class of low-cost and environmentally friendly adsorbents for radioactive iodine capture, and opened up ideas for the comprehensive utilization of waste lignin and natural clay minerals.

High efficiency removal of organic and inorganic iodine with ferrate[Fe(VI)] through oxidation and adsorption

I- is a halogen species existing in natural waters, and the transformation of organic and inorganic iodine in natural and artificial processes would impact the quality of drinking water. Herein, it was found that Fe(VI) could oxidize organic and inorganic iodine to IO3-and simultaneously remove the resulted IO3- through Fe(III) particles. For the river water, wastewater treatment plant (WWTP) effluent, and shale gas wastewater treated by 5 mg/L of Fe(VI) (as Fe), around 63 %, 55 % and 71 % of total iodine (total-I) had been removed within 10 min, respectively. Fe(VI) was superior to coagulants in removing organic and inorganic iodine from the source water. Adsorption kinetic analysis suggested that the equilibrium adsorption amount of I- and IO3- were 11 and 10.1 μg/mg, respectively, and the maximum adsorption capacity of IO3- by Fe(VI) resulted Fe(III) particles was as high as 514.7 μg/mg. The heterogeneous transformation of Fe(VI) into Fe(III) effectively improved the interaction probability of IO3- with iron species. Density functional theory (DFT) calculation suggested that the IO3- was mainly adsorbed in the cavity (between the γ-FeOOH shell and γ-Fe2O3 core) of Fe(III) particles through electrostatic adsorption, van der Waals force and hydrogen bond. Fe(VI) treatment is effective for inhibiting the formation of iodinated disinfection by-products in chlor(am)inated source water.

Mn3O4@polyaniline nanocomposite with multiple active sites to capture uranium(VI) and iodide: synthesis, performance, and mechanism

A major challenge for radioactive wastewater treatment and associated environmental remediation is how to simultaneously remove cationic and anionic radionuclides. Herein, a series of Mn₃O₄@polyaniline (Mn₃O₄@PANI) nanocomposites were successfully prepared and used to remove U(VI) and I^- from aqueous solution, two highly concomitant species in nuclear pollution settings. Batch adsorption experiments reveal that the component Mn₃O₄ is predominantly responsible for U(VI) removal, but PANI for I^-. The nanocomposite with 24.2 wt% Mn₃O₄ possesses high removal percentages (> 85%) either for U(VI) or I^- over a wide pH range, fast removal kinetics, and excellent adsorption selectivity at high concentrations of competing ions. Benefiting from the contributions of the two components and the high adsorption affinities, the nanocomposite achieves the simultaneous removal to coexisting U(VI) and I^-, with a maximum adsorption capacity 102.6 mg/g for U(VI) and 126.1 mg/g for I^-. X-ray photoelectron spectroscopy (XPS) results reveal that the U(VI) adsorption occurs via coordination bonding with Mn-O, -NH- , and =N- groups in the nanocomposite, whereas I^- adsorption proceeds mainly through I anionic species exchange with Cl^- and interactions with π-bonds in PANI, as well as the electrostatic attraction onto Mn₃O₄. Considering the excellent performance and multiple active sites, the Mn₃O₄@PANI nanocomposite is promising to remove practical radioactive U(VI) and I^-.

Enhanced removal of radioactive iodine anions from wastewater using modified bentonite: Experimental and theoretical study

Efficient and cost-effective removal of radioactive iodine anions from contaminated water has become a crucial task and a great challenge for waste treatment and environmental remediation. Herein, we present hexadecylpyridinium chloride monohydrate modified bentonite (HDPy-bent) for the efficient and selective removal of iodine anions (I^- and IO₃^-) from contaminated water. Batch experiments showed that HDPy-bent could remove more than 95% of I^- and IO₃^- within 10 min, and had maximum I^- and IO₃^- adsorption capacities of 80.0 and 50.2 mg/g, respectively. Competitive experiments indicated that HDPy-bent exhibited excellent I^- and IO₃^- selectivity in the excessive presence of common concomitant anions including PO₄^3-, SO₄^2-, HCO₃^-, NO₃^-, Cl^- (maximum mole ratio of anions vs iodine anions was ∼50,000). An anion exchange mechanism was proposed for the selective adsorption of iodine anions. Optimal adsorption structure of HDPy⁺/I^- (IO₃^-) at atomic level and driving forces of the I^- (IO₃^-) adsorption were calculated by density functional theory (DFT) simulations. Moreover, the good durability and reusability of the HDPy-bent has been demonstrated with 5 adsorption-desorption cycles. Dynamic column experiment also demonstrated that HDPy-bent exhibited excellent removal and fractional recovery capabilities towards I^- and IO₃^- from simulated groundwater and environmental water samples. In conclusion, this work presents a promising adsorbent material for the decontamination of radioactive iodine anions from wastewater on a large scale.

Study on Adsorption Behavior of Nickel Ions Using Silica-Based Sandwich Layered Zirconium-Titanium Phosphate Prepared by Layer-by-Layer Grafting Method

In this study, the composite of silica-based sandwich-layered zirconium-titanium phosphate was prepared by a layer-by-layer grafting method and its adsorption properties in a diluted solution of Ni ions were specifically researched by the bath experiment method. The field-emission scanning electron microscope (FESEM) results presented the smooth surface morphology of the pristine adsorbent and a rough surface morphology of the adsorbed adsorbent and the energy dispersive analysis (EDS) results ensured the presence of the original metal element (Si, O, Ti, P, Zr) and the captured nickel element on the adsorbent. The Fourier transformed infrared spectroscopy (FTIR) revealed the new band formation of -Si-Ti-O-, -Si-Ti-O-P-, and -Si-Ti-O-P-Zr-O-, which ensured the successful modification of the silica substrate by zirconium-titanium phosphate. The specific surface area and pore size distribution analysis indicated that the pore structure was changed from type-Ⅳ to H2-type and the specific surface area (BET) of the modified composite was 337.881 m²/g. In the bath experiment, the optimal pH for adsorbing Ni ions on the composite was ~8 with the equilibrium time 30 min at room temperature and the maximum sorption amount was 50.1 mg/g. The adsorption kinetics of the sorption process were corresponded to the pseudo-second-order kinetic equation and the isothermal adsorption data were fitted well to the Redlich-Peterson Model. Thermodynamic simulation results revealed the species of Ni ions and provided a reasonable pH scope for better removal of the Ni element in wastewater.

Synthesis of Silver-Impregnated Magnetite Mesoporous Silica Composites for Removing Iodide in Aqueous Solution

Mag@silica-Ag composite has a high sorption ability for I- in aqueous solution due to its high surface area and strong affinity for the studied anion. The material adsorbed I- rapidly during the initial contact time (in 45 min, η = 80%) and reached adsorption equilibrium after 2 h. Moreover, mag@silica-Ag proved to selectively remove I- from a mixture of Cl-, NO3- and I-. The adsorption behavior fitted the Langmuir isotherm perfectly and the pseudo-second-order kinetic model. Based on the Langmuir isotherm, the maximum adsorption capacity of mag@silica-Ag was 0.82 mmol/g, which is significantly higher than previously developed adsorbents. This study introduces a practical application of a high-capacity adsorbent in removing radioactive I- from wastewaters.

Comparison of Structure and Adsorption Properties of Mesoporous Silica Functionalized with Aminopropyl Groups by the Co-Condensation and the Post Grafting Methods

The adsorptive potential has been evaluated for the aminopropyl functionalized mesoporous silica materials obtained by co-condensation and post grafting methods. Nitrogen sorption, small angle neutron and X-ray scattering (SANS and SAXS) demonstrated high surface area and well-ordered hexagonal pore structure suitable for applications as adsorbents of metals from waste waters. A comparison of Cr(VI) adsorption properties of the materials prepared by different functionalization methods has been performed. The obtained results demonstrated the adsorption capacity due to the affinity of the chromium ions to the amino groups, and showed that co-condensation of tetraethoxysilane (TEOS) and 3-aminopropyl triethoxysilane (APTES) resulted in higher metal sorption capacity of the materials compared to post-synthesis grafting of aminopropyl groups onto the mesoporous silica particles.

Rapid iodine capture from radioactive wastewater by green and low-cost biomass waste derived porous silicon–carbon composite

The effective and safe capture and storage of radioactive iodine (¹²⁹I or ¹³¹I) are of significant importance during nuclear waste storage and nuclear energy generation. Herein, a porous silicon–carbon (pSi–C) composite derived from paper mill sludge (PMS) is synthesized and used for rapid iodine capture. The influences of the activator type, the impregnation ratio of the paper mill sludge to the activator, carbonization temperature, and carbonization time on the properties of the pSi–C composite are investigated. The pSi–C composite produced in the presence of ZnCl₂ as the activator and at an impregnation ratio of 1 : 1, a carbonization temperature of 550 °C, and a carbonization time of 90 min has a surface area of 762.13 m² g⁻¹. The as-synthesized pSi–C composite exhibits promising iodine capture performance in terms of superior iodine adsorption capacity (q_t) of around 250 mg g⁻¹ and rapid equilibrium adsorption with in 15 min. The devised method is environmentally friendly and inexpensive and can easily be employed for the large-scale production of porous silicon-activated carbon composites with excellent iodine capture and storage from iodine-contaminated water.

The effective and safe capture and storage of radioactive iodine (¹²⁹I or ¹³¹I) are of significant importance during nuclear waste storage and nuclear energy generation.

Efficient removal of iodide anion from aqueous solution with recyclable core-shell magnetic Fe3O4@Mg/Al layered double hydroxide (LDH)

Magnetic Mg/Al layered double hydroxides (LDH) with three cationic ratios (Mg/Al = 2:1, 3:1, and 4:1) were successfully synthesized and utilized for the first time in an iodide adsorption study. The effects of the Mg/Al ratio of LDH on iodide adsorption were investigated, and physicochemical properties of synthetic LDHs depending on Mg/Al ratio were confirmed by XRD, TEM, ICP-OES, VSM, Zeta-potential, and BET analyses. The ferrimagnetic property was well preserved even after a coating of LDH on magnetite irrespective of the Mg/Al ratio. Among the three Mg/Al ratios, the calcined Fe₃O₄@4:1 Mg/Al LDH exhibited excellent performance for iodide removal with 105.04 mg/g of the maximum iodide adsorption capacity due to its wide interlayer spacing and largest BET surface area. In the presence of competing carbonate anions, the Fe₃O₄@4:1 LDH showed removal rate of >80% at a dosage of over 3 g/L solid to liquid ratio. The recyclability test of Fe₃O₄@4:1 LDH showed that the removal performance for iodide is maintained at >80% even during the first to the fourth cycles. These results demonstrated that the magnetic Mg/Al LDH adsorbent can be effectively utilized for remediation of radioactive iodide anions with high efficiency and economics.

DFT study on MgAl-layered double hydroxides with different interlayer anions: structure, anion exchange, host–guest interaction and basic sites

The guest anions play a key role in the construction of layered double hydroxide (LDH)-based host–guest functional materials.

Functionalized Porous Silica-Based Nano/Micro Particles for Environmental Remediation of Hazard Ions

The adsorption and separation of hazard metal ions, radioactive nuclides, or minor actinides from wastewater and high-level radioactive waste liquids using functional silica-based nano/micro-particles modified with various inorganic materials or organic groups, has attracted significant attention since the discovery of ordered mesoporous silica-based substrates. Focusing on inorganic and organic modified materials, the synthesis methods and sorption performances for specific ions in aqueous solutions are summarized in this review. Three modification methods for silica-based particles, the direct synthesis method, wetness impregnation method, and layer-by-layer (LBL) deposition, are usually adopted to load inorganic material onto silica-based particles, while the wetness impregnation method is currently used for the preparation of functional silica-based particles modified with organic groups. Generally, the specific synthesis method is employed based on the properties of the loading materials and the silicon-based substrate. Adsorption of specific toxic ions onto modified silica-based particles depends on the properties of the loaded material. The silicon matrix only changes the thermodynamic and mechanical properties of the material, such as the abrasive resistance, dispersibility, and radiation resistance. In this paper, inorganic loads, such as metal phosphates, molybdophosphate, titanate-based materials, and hydrotalcite, in addition to organic loads, such as 1,3-[(2,4-diethylheptylethoxy)oxy]-2,4-crown-6-Calix{4}arene (Calix {4}) arene-R14 and functional 2,6-bis-(5,6-dialkyl-1,2,4-triazin-3-yl)-pyridines(BTP) are reviewed. More specifically, we emphasize on the synthesis methods of such materials, their structures in relation to their capacities, their selectivities for trapping specific ions from either single or multi-component aqueous solutions, and the possible retention mechanisms. Potential candidates for remediation uses are selected based on their sorption capacities and distribution coefficients for target cations and the pH window for an optimum cation capture.

Decontamination of radioactive wastewater: State of the art and challenges forward

Radioactive substances have been widely used in many industrial sectors, e.g. nuclear power station, biomedical engineering, etc. With increasing applications of nuclear technology, more and more radioactive wastewater is being generated via different channels, which indeed is posing an emerging challenge and threat to the environment and human health. Given such a situation, this review attempts to offer a holistic view with regard to the state of the art of technology for decontamination of radioactive wastewater as well as shed lights on the challenges forward. Different from reclamation of other types of wastewaters, the most challenging issue in decontamination of radioactive wastewater is the effective stabilization and solidification of soluble radioactive nuclides present in wastewater, which are critical for final disposal. Moreover, the potential risk of human exposure to wastewater radiation needs to be carefully assessed, and this issue should also be taken into consideration in the selection, design and operation of the radioactive wastewater treatment process. These clearly differentiate the treatment principle of radioactive wastewater from those of traditional industrial and municipal wastewaters. Lastly, the challenges from the perspectives of technology development, environmental and human health impacts and possible solutions forward are also elucidated.