Heterojunction photocatalyst fabricated by deposition Co3O4 nanoparticles on MoS2 nanosheets with enhancing photocatalytic performance and mechanism insight

Effects of Co3O4 modified with MoS2 on microbial fuel cells performance

In this study, Co3O4@MoS2 is prepared as anodic catalytic material for microbial fuel cells (MFCs). As the mass fraction of MoS2 is 20%, the best performance of Co3O4@MoS2 composite catalytic material is achieved, and the addition of MoS2 enhances both the electrical conductivity and catalytic performance of the composite catalyst. Through the structural characterization of Co3O4@MoS2 composite catalytic material, nanorod-like Co3O4 and lamellar MoS2 interweaved and stacked each other, and the agglomeration of Co3O4 is weakened. Among the four groups of single-chamber MFCs constructed, the Co3O4@MoS2-MFC shows the best power production performance with a maximum stable output voltage of to 539 mV and a maximum power density of up to 2221 mW/m2. Additionally, the ammonia nitrogen removal rate of the MFCs loaded with catalysts is enhanced by about 10% compared with the blank carbon cloth MFC. Overall, the findings suggest that Co3O4@MoS2 composite catalysts can significantly improve the performance of MFCs, making them more effective for both energy production and wastewater treatment.

Au nanoparticles decorated graphitic carbon nitride nanosheets as a sensitive and selective fluorescence probe for Fe3+ and dichromate ions in aqueous medium

Graphitic carbon nitride mutated with metal nanoparticles has captivated great interest as an effective fluorescent sensor for the detection of harmful ions present in water. In the present work, bulk-gCN was synthesized using melamine as precursor, and further Au-gCN nanocomposite were fabricated via in-situ direct reduction deposition method. The structural, morphological, compositional, stability and optical properties of bulk gCN and Au-gCN nanocomposite were examined using various scattering and spectroscopic techniques such as HRTEM, XPS, XRD and SEM. The synthesized bulk gCN straggles during selectivity studies with different cations and anions because of its uneven surface morphology, however in Au-gCN gold nanoparticles are uniformly distributed on the gCN sheets which results in its enhanced selectivity over bulk gCN. This leads to the fabrication of an optical sensor for Fe3+ and Cr2O72- ions with limit of detection of 4.62 and 2.77 μM, respectively. The sensing of Fe3+ ions corresponds to the photoinduced electron transfer (PET) mechanism, while the detection of chromate species is associated with an inner filter effect (IFE). The practical applicability of the sensor was also evaluated for different environmental water samples. The high stability, sensitivity, and specificity of Au-gCN nanocomposite make it a potential fluorescent probe for Fe3+ and Cr2O72- ions in water samples.

NCQDs active sites as effective collectors of charge carriers towards enhanced photocatalytic activity of porous Co3O4

In this work, different proportions of N-doped carbon quantum dots/porous Co3O4 (NCQDs/p-Co3O4) NCQDs/Co3O4 composite photocatalysts were prepared by a simple self-assembly method. It was demonstrated by a series of characterizations that 50% NCQDs/Co3O4 has a good visible light response and low electrochemical impedance. The photocatalytic degradation of TC was investigated by the 50% NCQDs/p-Co3O4 composite photocatalyst, and the results showed that the degradation effect of TC reached 81.2% within 120 min. The higher photocatalytic activity of 50% NCQDs/p-Co3O4 was analyzed probably because NCQDs can improve the separation efficiency of photogenerated electron-hole pairs and p-Co3O4 can provide a larger specific surface area and thus has more active sites. This study provides a new strategy for improving the photodegradation activity of Co3O4 photocatalysts.

Recent advances of modification effect in Co3O4-based catalyst towards highly efficient photocatalysis

Tricobalt tetroxide (Co3O4) has been developed as a promising photocatalyst material for various applications. Several reports have been published on the self-modification of Co3O4 to achieve optimal photocatalytic performance. The pristine Co3O4 alone is inadequate for photocatalysis due to the rapid recombination process of photogenerated (PG) charge carriers. The modification of Co3O4 can be extended through the introduction of doping elements, incorporation of supporting materials, surface functionalization, metal loading, and combination with other photocatalysts. The addition of doping elements and support materials may enhance the photocatalysis process, although these modifications have a slight effect on decreasing the recombination process of PG charge carriers. On the other hand, combining Co3O4 with other semiconductors results in a different PG charge carrier mechanism, leading to a decrease in the recombination process and an increase in photocatalytic activity. Therefore, this work discusses recent modifications of Co3O4 and their effects on its photocatalytic performance. Additionally, the modification effects, such as enhanced surface area, generation of oxygen vacancies, tuning the band gap, and formation of heterojunctions, are reviewed to demonstrate the feasibility of separating PG charge carriers. Finally, the formation and mechanism of these modification effects are also reviewed based on theoretical and experimental approaches to validate their formation and the transfer process of charge carriers.

2D-2D Nanoheterostructure of an Exposed {001}-Facet CuO and MoS2 Based Bifunctional Catalyst Showing Excellent Surface Chemistry and Conductivity for Cathodic CO2 Reduction

A novel CuO-MoS2 based heterostructure catalyst model system is proposed where a CuO nanosheet with exposed {001} facet with proper termination is the active surface for the catalysis and a MoS2 nanosheet is the supporting layer. Density functional theory (DFT) calculations were performed to validate the model. The MoS2 bilayer forms a stable heterostructure with {001} faceted CuO with different terminations exposing oxygen and copper atoms (active sites) on the surface. The heterostructure active sites with a low oxidation state of the copper atoms and subsurface oxygen atoms provide a suitable chemical environment for the selective production of multicarbon products from CO2 electrocatalytic reduction. Furthermore, our heterostructure model exhibits good electrical conductivity, efficient electron transport to active surface sites, and less interfacial resistance compared to similar heterostructure systems. Additionally, we propose a photoenhanced electrocatalysis mechanism due to the photoactive nature of MoS2. We suggest that the photogenerated carrier separation occurs because of the interface-induced dipole. Moreover, we utilized a machine learning model trained on a 2D DFT materials database to predict selected properties and compared them with the DFT results. Overall, our study provides insights into the structure-property relationship of a MoS2 supported 2D CuO nanosheet based bifunctional catalyst and highlights the advantages of heterostructure formation with selective morphology and properly terminated surface in tuning the catalytic performance of nanocomposite materials.

PVP encapsulated MXene coated on PET surface (PMP)-based photocatalytic materials: A novel photo-responsive assembly for the removal of tetracycline

Tetracycline (TC) antibiotic that is effective against wide-range micro-organisms, thereby used to control bacterial infection. The partial metabolism of TC antibiotics in humans and animals leads to the contamination of TC in the environments like water bodies. Thus, requirements to treat/remove/degrade TC antibiotics from the water bodies to control environmental pollution. In this context, this study focuses on fabricating PVP-MXene-PET (PMP) based photo-responsive materials to degrade TC antibiotics from the water. Initially, MXene (Ti2CTx) was synthesized using a simple etching process from the MAX phase (Ti3AlC2). The synthesized MXene was encapsulated using PVP and cast onto the surface of PET to fabricate PMP-based photo-responsive materials. The rough surface and micron/nano-sized pores within the PMP-based photo-responsive materials might be improved the photo-degradation of TC antibiotics. The synthesized PMP-based photo-responsive materials were tested against the photo-degradation of TC antibiotics. The band gap value of the MXene and PMP-based photo-responsive materials was calculated to be ∼1.23 and 1.67 eV. Incorporating PVP within the MXene increased the band gap value, which might be beneficial for the photo-degradation of TC, as the minimum band gap value should be ∼1.23 eV or more for photocatalytic application. The highest photo-degradation of ∼83% was achieved using PMP-based photo-degradation at 0.1 mg/L of TC. Furthermore, ∼99.71% of photo-degradation of TC antibiotics was accomplished at pH ∼10. Therefore, the fabricated PMP-based photo-responsive materials might be next-generation devices/materials that efficiently degrade TC antibiotics from the water.

Synthesis of a novel solid mediator Z-scheme heterojunction photocatalysis Fe3O4/C/uio66-nh2: Used for oxidation of Rh6G in water

A novel mediator Z-scheme photocatalyst, Fe3O4/C/UiO-66-NH2, was designed, synthesized, and characterized using SEM, TEM, FTIR, XRD, EPR, and XPS. Formulas #1 to #7 were examined using dye Rh6G dropwise tests. Carbonization of glucose forms the mediator carbon, which connects two semiconductors, Fe3O4 and UiO-66-NH2, to construct the Z-scheme photocatalyst. Formula #1 generates a composite with photocatalyst activity. The band gap measurements of the constituent semiconductors support the mechanisms for the Rh6G degradation using this novel Z-scheme photocatalyst. The successful synthesis and characterization of the proposed novel Z-scheme confirm the feasibility of the tested design protocol for environmental purposes.

Defect mediated visible light induced photocatalytic activity of Co3O4 nanoparticle decorated MoS2 nanoflower: A combined experimental and theoretical study

In this work, Co₃O₄ nanoparticle-decorated MoS₂ (MoS₂@Co₃O₄) hetero-nanoflowers were synthesized by a facile hydrothermal method, and the effect of Co₃O₄ on the morphological, structural, optical, electronic, and photocatalytic properties of MoS₂ was analyzed. The surface morphology of MoS₂ and MoS₂@Co₃O₄ was studied via field emission electron microscopy (FE-SEM) and transmission electron microscopy (TEM), which revealed a strong interaction between the MoS₂ nanoflower and the nanoparticles. The X-ray diffraction pattern showed a decrease in the crystallite sizes from 7.35 nm to 6.26 nm due to the incorporation of Co₃O₄. The UV-Vis spectroscopy of the analysis revealed that the indirect band gap of MoS₂ was reduced from 1.89 eV to 1.65 eV with the incorporation of Co₃O₄ nanoparticles. Density functional theory (DFT) calculations were used to investigate the electronic properties of MoS₂ and MoS₂@Co₃O₄ hetero-nanoflowers, which also showed a reduction in the electronic band gap for the Co₃O₄ nanoparticles that were injected. The presence of defect states was also observed in the electronic property of MoS₂@Co₃O₄. The photocatalytic activity of the prepared composite and nanoflower is studied using an aqueous solution of methylene blue (MB), and the efficiencies are found to be 27.96% for MoS₂ and 78.89% for MoS₂@Co₃O₄. The improved photocatalytic efficiency of MoS₂@Co₃O₄ hetero-nanoflower can be attributed to narrowing the band gap together with the creation of defect states by the injection of nanoparticles that slows down electron-hole recombination rate by trapping charge carrier. The degradation analysis of the composite provides a new route for the purification of polluted water.

Synthesis of a novel solid mediator Z-scheme heterojunction photocatalysis CuFe2O4/Cu/UiO-66-NH2 for oxidation of dye in water

Metal mediator Z-scheme photocatalyst comprises three elements: two semiconductors and a sandwiched metal mediator, so the catalyst can effectively degrade pollutants using visible lights. Proper design and synthesis of Z-scheme with targeted performance has not been systematically proposed. This work proposed the protocol to design and synthesize a Z-scheme photocatalyst with targeted performance. A novel metal mediator Z-scheme photocatalyst CuFe₂O₄/Cu/UiO-66-NH₂ was used to implement the design proposal. After determining synthesis protocol from the theory, the concentrations of three reagents - glucose, l-cysteine, and precursor of UiO-66-NH₂ for synthesizing Z-scheme photocatalyst were revised to achieve successful photocatalyst. Dropwise photocatalytic tests were performed to confirm the activities of the synthesized catalysts using 0.112 mmol/mL UiO-66-NH₂ precursor, 10 mmol/mL glucose, and 1 mmol/mL l-cysteine yielded effective photocatalyst to degrade rhodamine 6G. The dye degradation tests and EPR tests confirmed the successful synthesis of the designed Z-scheme photocatalyst.

Pollutant degradation with mediator Z-scheme heterojunction photocatalyst in water: A review

The Z-scheme heterojunction is a photocatalyst with narrow band gap and sufficiently high oxidization and reduction powers for degradation of pollutants in waters. This review firstly summarizes the fundamentals of photocatalysis, and explains the need to develop Z-scheme heterojunctions to harvest energy from sunlight effectively. Secondly, contemporary reports of degradation wastewater pollutants, including organic dyes, antibiotics, and other chemicals are reviewed and discussed. A challenge in the selection of an appropriate Z-scheme for removing a specific pollutant is the lack of available energy levels that are offered by the catalyst and the lack of redox energy levels that are required to break down essential chemical bonds of the pollutants. With reference to the redox energy levels offered by the active photocatalytic species, the redox energy levels of specific pollutants studied in literature are estimated. Challenges and prospects concerning the use of the Z-scheme to degrade recalcitrant pollutants under irradiation by sunlight are outlined at the end of this review.

Hybridized 2D Nanomaterials Toward Highly Efficient Photocatalysis for Degrading Pollutants: Current Status and Future Perspectives

Organic pollutants including industrial dyes and chemicals and agricultural waste have become a major environmental issue in recent years. As an alternative to simple adsorption, photocatalytic decontamination is an efficient and energy-saving technology to eliminate these pollutants from water environment, utilizing the energy of external light, and unique function of photocatalysts. Having a large specific surface area, numerous active sites, and varied band structures, 2D nanosheets have exhibited promising applications as an efficient photocatalyst for degrading organic pollutants, particularly hybridization with other functional components. The novel hybridization of 2D nanomaterials with various functional species is summarized systematically with emphasis on their enhanced photocatalytic activities and outstanding performances in environmental remediation. First, the mechanism of photocatalytic degradation is given for discussing the advantages/shortcomings of regular 2D materials and identifying the importance of constructing hybrid 2D photocatalysts. An overview of several types of intensively investigated 2D nanomaterials (i.e., graphene, g-C₃ N₄ , MoS₂ , WO₃ , Bi₂ O₃ , and BiOX) is then given to indicate their hybridized methodologies, synergistic effect, and improved applications in decontamination of organic dyes and other pollutants. Finally, future research directions are rationally suggested based on the current challenges.

Electrochemical detection of thiamethoxam in food samples based on Co3O4 Nanoparticle@Graphitic carbon nitride composite

Thiamethoxam is a class of neonicotinoid insecticide widely used in agriculture. Due to their high water solubility, thiamethoxam can be transported to surface waters and have the potential to be toxic to human life. Herein, a simple and robust method is presented for the detection of thiamethoxam based on hydrothermally synthesized nanoparticles of cobalt oxide into the graphitic carbon nitride composite (Co₃O₄@g-C₃N₄ NC). The materials were well characterized by XRD, FT-IR, XPS, FESEM, HRTEM, EDX, and UV-vis which provide crystalline nature, structure, and composition. The impedance measurement shows an intimate electrode/electrolyte interface by casting Co₃O₄@g-C₃N₄ onto a screen-printed carbon electrode (SPCE), delivering an interfacial resistance as low as 12.5 Ωcm². The cyclic voltammetry and differential pulse voltammetry measurements exhibit the nanocomposite as a superior electrocatalyst for the electrochemical detection of thiamethoxam and achieved a low detection limit of 4.9 nM with a wide linear range of 0.01-420 μM. The present work also demonstrates a promising strategy for electrochemical detection of thiamethoxam in real samples such as potato and brown rice.

Fabrication of a Z-scheme MoS2/CuO heterojunction for enhanced 2-mercaptobenzothiazole degradation activity and mechanism insight

A Z-scheme MoS₂/CuO photocatalyst is successfully developed using a hydrothermal and calcination method, which has excellent activity (96%) in the degradation of 2-mercaptobenzothiazole (MBT) under visible light irradiation.

Z-scheme MoS2/Bi2O3 heterojunctions: enhanced photocatalytic degradation performance and mechanistic insight

A new Z-scheme MoS₂/Bi₂O₃ heterojunction photocatalyst was successfully prepared using a facile and practical hydrothermal method.