Introduction of arteriovenous grafts with graft insertion anastomosis for hemodialysis access

Novel electrospun polyurethane grafts for vascular access in rats

OBJECTIVES

The purpose of this study is to develop a new and improved polyurethane (PU) graft using electrospinning and chemical modifications for hemodialysis patients, which will replace the current standard, polytetrafluoroethylene (PTFE) graft. The chemical modifications aim to improve hemocompatibility and reduce thrombogenicity and neointimal hyperplasia.

METHOD

The study population was randomized and divided equally into four groups; one control group received a PTFE graft, and three treatment groups received three different types of polyurethane grafts. Two duplex measurements were performed directly on the graft on the same locations, followed by a histologic examination.

RESULTS

In the first few days after the implantation animals lost some weight, it took a week to recover to pre-surgical weight. Throughout the 28 days, there was no significant difference between animals in wound, activity, and the general appearance. PTFE and PU A groups have lower compliance or reduced graft diameter due to neointimal hyperplasia development on Doppler interrogation. The histological analysis showed limited neointimal hyperplasia development and no excessive inflammatory response to any of the grafts.

CONCLUSION

This study demonstrates that animals with polyurethane grafts show better blood flow because the developed NIH was inconspicuous, as indicated by the different velocity measure than controls on Duplex and minimal NIH development microscopically.

Novel reinforcement of corrugated nanofiber tissue-engineered vascular graft to prevent aneurysm formation for arteriovenous shunts in an ovine model

Objective

Many patients who require hemodialysis treatment will often require a prosthetic graft after multiple surgeries. However, the patency rate of grafts currently available commercially has not been satisfactory. Tissue engineering vascular grafts (TEVGs) are biodegradable scaffolds created to promote autologous cell proliferation and functional neotissue regeneration and, accordingly, have antithrombogenicity. Therefore, TEVGs can be an alternative prosthesis for small diameter grafts. However, owing to the limitations of the graft materials, most TEVGs are rigid and can easily kink when implanted in limited spaces, precluding future clinical application. Previously, we developed a novel corrugated nanofiber graft to prevent graft kinking. Reinforcement of these grafts to ensure their safety is required in a preclinical study. In the present study, three types of reinforcement were applied, and their effectiveness was examined using large animals.

Methods

In the present study, three different reinforcements for the graft composed of corrugated poly-ε-caprolactone (PCL) blended with poly(L-lactide-co-ε-caprolactone) (PLCL) created with electrospinning were evaluated: 1) a polydioxanone suture, 2) a 2-0 polypropylene suture, 3) a polyethylene terephthalate/polyurethane (PET/PU) outer layer, and PCL/PLCL as the control. These different grafts were then implanted in a U-shape between the carotid artery and jugular vein in seven ovine models for a total of 14 grafts during a 3-month period. In evaluating the different reinforcements, the main factors considered were cell proliferation and a lack of graft dilation, which were evaluated using ultrasound examinations and histologic and mechanical analysis.

Results

No kinking of the grafts occurred. Overall, re-endothelialization was observed in all the grafts at 3 months after surgery without graft rupture or calcification. The PCL/PLCL grafts and PCL/PLCL grafts with a polydioxanone suture showed high cell infiltration; however, they had become dilated 10 weeks after surgery. In contrast, the PCL/PLCL graft with the 2-0 suture and the PCL/PLCL graft covered with a PET/PU layer did not show any graft expansion. The PCL/PLCL graft covered with a PET/PU layer showed less cell infiltration than that of the PCL/PLCL graft.

Conclusions

Reinforcement is required to create grafts that can withstand arterial pressure. Reinforcement with suture materials has the potential to maintain cell infiltration into the graft, which could improve the neotissue formation of the graft.

In our basic science research study, we investigated tissue engineered vascular grafts for arteriovenous shunts. Our grafts were created with poly-ε-caprolactone and poly(L-lactide-co-ε-caprolactone) and designed with corrugated walls to avoid graft kinking. The grafts were implanted between the carotid artery and external jugular vein in a U-shape using an ovine model. To withstand the high pressure of blood on the arterial system, two types of reinforcement were applied to these tissue engineering vascular grafts. Because reinforcement of the graft could interfere with cell infiltration into the tissue engineering vascular grafts, the methods and material of reinforcement were investigated, in addition to the mechanical properties of the graft.

A critical review of surgical strategies to minimise venous stenosis in arteriovenous grafts

It is inevitable that complications arising from surgical procedures are ascribed to surgical technique, and this applies to venous stenosis (VS) in arteriovenous grafts. However, despite a wide range of cellular studies, computer modelling, observational series and clinical trials, there remains uncertainty on whether surgical technique contributes to VS. This article reviews evidence from basic science, fluid dynamics and clinical data to try and rationalise the main surgical options to modify the occurrence of venous stenosis. There is sufficient data from diverse sources to make recommendations on clinical practice (size of target vein, shape of anastomosis, angle of approach, distance from venous needling, trauma to the target vein) whilst at the same time this emphasises the need to carefully report the practical aspects of surgical technique in future clinical trials.