Biomechanical evaluation of opening-wedge high tibial osteotomy with composite materials using finite-element analysis

Effect of surface matching mismatch of focal knee articular prosthetic on tibiofemoral contact stress using finite element analysis

Aims

Focal knee arthroplasty is an attractive alternative to knee arthroplasty for young patients because it allows preservation of a large amount of bone for potential revisions. However, the mechanical behaviour of cartilage has not yet been investigated because it is challenging to evaluate in vivo contact areas, pressure, and deformations from metal implants. Therefore, this study aimed to determine the contact pressure in the tibiofemoral joint with a focal knee arthroplasty using a finite element model.

Methods

The mechanical behaviour of the cartilage surrounding a metal implant was evaluated using finite element analysis. We modelled focal knee arthroplasty with placement flush, 0.5 mm deep, or protruding 0.5 mm with regard to the level of the surrounding cartilage. We compared contact stress and pressure for bone, implant, and cartilage under static loading conditions.

Results

Contact stress on medial and lateral femoral and tibial cartilages increased and decreased, respectively, the most and the least in the protruding model compared to the intact model. The deep model exhibited the closest tibiofemoral contact stress to the intact model. In addition, the deep model demonstrated load sharing between the bone and the implant, while the protruding and flush model showed stress shielding. The data revealed that resurfacing with a focal knee arthroplasty does not cause increased contact pressure with deep implantation. However, protruding implantation leads to increased contact pressure, decreased bone stress, and biomechanical disadvantage in an in vivo application.

Conclusion

These results show that it is preferable to leave an edge slightly deep rather than flush and protruding.

Homogeneous material models can overestimate stresses in high tibial osteotomy: A finite element analysis

Although widely used numerical models can assess the stability of lateral hinges in high tibial osteotomy (HTO) and may provide acceptable results in comparative studies, accurate stress prediction may not be possible due to simplified homogeneous models of the bone. The present study aimed to investigate the effect of a heterogeneous versus four homogeneous models on the results of stress and force. Each of the four homogenized FE models utilized the same elastic modulus of 16,700 MPa for the cortical while employing a single elastic modulus varying from 155 to 5000 MPa for the cancellous. In heterogeneous model, the modulus of each element was assigned using the bone density. It was found that stresses at the hinge in homogeneous models were higher than those in the heterogeneous model. The maximum principal stress (MPS) was 437 MPa for the heterogeneous model while that was 2179, 2351, 2581, and 2637 MPa for the homogeneous models with the elastic moduli of 155, 500, 2130, and 5000 MPa, respectively. Also, the opening force was 150 N for the heterogeneous model significantly lower than 649-1534 N range predicted for the homogeneous models. The use of a homogeneous model in the FE analysis of HTO overestimated the stresses and force. Thus, in addition to casting doubt on the use of a single modulus in the numerical analysis of HTO, Future HTO studies can use our results as a benchmark for comparison purposes and highlight the use of patient-specific bone density - elastic modulus relation in simulation.

Hinge location and apical drill holes in opening wedge high tibial osteotomy: A finite element analysis

At the time of medial opening wedge high tibial osteotomy (HTO) to realign the lower limb and offload medial compartment knee osteoarthritis, unwanted fractures can propagate from the osteotomy apex. The aim of this study was to use finite element (FE) analysis to determine the effect of hinge location and apical drill holes on cortical stresses and strains in HTO. A monoplanar medial opening wedge HTO was created above the tibial tuberosity in a composite tibia. Using the FE method, intact lateral hinges of different widths were considered (5, 7.5, and 10 mm). Additional apical drill holes (2, 4, and 6 mm diameters) were then incorporated into the 10 mm hinge model. The primary outcome measure was the maximum principal strain in the cortical bone surrounding the hinge axis. Secondary outcomes included the force required for osteotomy opening, minimum principal strain, and mean cortical bone stresses (maximum principal/minimum principal/von Mises). Larger intact hinges (10 mm) were associated with higher cortical bone maximum principal strain and stress, lower minimum principal strain/stress, and required greater force to open. Lateral cortex strain concentrations were present in all scenarios, but extended to the joint surface with the 10 mm hinge. Apical drill holes reduced the mean cortical bone maximum principal strain adjacent to the hinge axis: 2 mm hole 6% reduction; 4 mm 35% reduction; and 6 mm 55% reduction. Incorporating a 4-mm apical drill hole centered 10 mm from the intact lateral cortex maintains a cortical bone hinge, minimizes cortical bone strains and reduces the force required to open the HTO; thus improving control.

Biomechanical aspects of the posteromedial split in bicondylar tibial plateau fractures-a finite-element investigation

PURPOSE

To gain principal insight into fixation techniques of a posteromedial split fragment in bicondylar tibial plateau fractures.

METHODS

A computer simulation was performed, applying the finite-element method (FEM) to compare four methods of fixation of the posteromedial split fragment: lateral plate (model 1), lateral plate and kickstand screw (model 2), lateral plate and two antero-posterior lag screws (model 3), and lateral and posteromedial plate (model 4). The displacement of the fragment and material stresses in implants and bone under 2500 N axial load were analyzed.

RESULTS

Maximal displacement of the posteromedial split fragment of 2.8 mm was found with a sole lateral plate. An added kickstand screw decreased the displacement to 1.46 mm. Added lag screws improved stability by a factor 4, with a maximal displacement of 0.76 mm. The double-plate configuration revealed 0.27 mm, a decrease of the displacement by a factor 10 compared to model 1. An additional analysis of posteromedial fragment displacements with osteoporotic bone, simulated by dividing the elastic modulus of the bone by a factor 2, turned out to be of relevant impact. For model 1, the calculations did not converge. The influence of bone quality was found to be 70% in model 2, 60% in model 3, and 40% in model 4.

CONCLUSIONS

The results indicate that the additional fixation of a posteromedial split fracture by plate osteosynthesis might be advantageous in bicondylar tibial plateau fractures treated with lateral plating. This might be even more important in patients with low bone quality.

Biomechanical effect of a lateral hinge fracture for a medial opening wedge high tibial osteotomy: finite element study

BACKGROUND

This study aimed to investigate the biomechanical effect on the Takeuchi classification of lateral hinge fracture (LHF) after an opening wedge high tibial osteotomy (HTO).

METHODS

We performed an FE simulation for type I, type II, and type III in accordance with the Takeuchi classification. The stresses on the bone and plate, wedge micromotion, and forces on ligaments were evaluated to investigate stress-shielding effect, plate stability, and biomechanical change, respectively, in three different types of LHF HTO and with the HTO without LHF model (non-LHF) models.

RESULTS

The greatest stress-shielding effect and wedge micromotion were observed in type II LHF (distal portion fracture). The type II and type III (lateral plateau fracture) models exhibited a reduction in ACL force and an increase in PCL force compared with the HTO without LHF model. However, the type I (osteotomy line fracture) and HTO without LHF models did not exhibit a significant biomechanical effect. This study demonstrates that Takeuchi type II and type III LHF models provide unstable structures compared with the type I and HTO without LHF models.

CONCLUSIONS

HTO should be performed while considering a medial opening wedge HTO to avoid a type II and type III LHF as a potential complication.