Synergistic amplification of (photo)catalytic oxygen and hydrogen generation from water by thin-film polypyrrole composites

Stable and Efficient Photoinduced Charge Transfer of MnFe2O4/Polyaniline Photoelectrode in Highly Acidic Solution

Tailoring conductive polymers with inorganic photocatalysts, which provide photoinduced electron-hole generation, have significantly enhanced composites leading to excellent photoelectrodes. In this work, MnFe2O4 nanoparticles prepared by a hydrothermal method were combined with polyaniline to prepare mixed (hybrid) slurries, which were cast onto flexible FTO to prepare photoelectrodes. The resulting photoelectrodes were characterized by XRD, FESEM, HRTEM and UV-VIS. The photoelectrochemical performance was investigated by linear sweep voltammetry and chronoamperometry. The photocurrent achieved by MnFe2O4/Polyaniline was 400 μA/cm2 at 0.8 V vs. Ag/AgCl in Na2SO4 (pH = 2) at 100 mW/cm2, while polyaniline alone achieved only 25 μA/cm2 under the same conditions. The best MnFe2O4/Polyaniline displayed an incident photon-to-current conversion efficiency (IPCE) and applied bias photon-to-current efficiency (ABPE) of 60% at 405 nm wavelength, and 0.17% at 0.8 V vs. Ag/AgCl, respectively. High and stable photoelectrochemical performance was achieved for more than 900 s in an acidic environment.

Conducting-Polymer Nanocomposites as Synergistic Supports That Accelerate Electro-Catalysis: PEDOT/Nano Co3O4/rGO as a Photo Catalyst of Oxygen Production from Water

This work describes how conducting polymer nanocomposites can be employed as synergistic supports that significantly accelerate the rate of electro-catalysis. The nanocomposite PEDOT/nano-Co3O4/rGO is discussed as an example in this respect, which is specific for photo electro-catalytic oxygen (O2) generation from water using light (PEDOT = poly (3,4-ethylenedioxythiophene); rGO = reduced graphene oxide). We show that the conducting polymer PEDOT and the conductive additive rGO may be used to notably amplify the rate of O2-generation from water by the nano catalyst, Co3O4. A composite film containing the precise molar ratio 7.18 (C; PEDOT):1 (Co):5.18 (C; rGO) exhibited high photocatalytic activity (pH 12) for the oxygen evolution reaction (OER) at 0.80 V (vs. Ag/AgCl), with a current density of 1000 ± 50 μA/cm2 (including a photocurrent of 500 μA/cm2), achieved after >42 h of operation under illumination with a light of intensity 0.25 sun. By comparison, the best industrial catalyst, Pt, yielded a much lower 150 μA/cm2 under the same conditions. Oxygen gas was the sole product of the reaction.

Effect of Electrosynthesis Potential on Nucleation, Growth, Adhesion, and Electronic Properties of Polypyrrole Thin Films on Fluorine-Doped Tin Oxide (FTO)

Polypyrrole (PPy) is one of the most attractive conducting polymers for thin film applications due to its good electrical conductivity, stability, optical properties, and biocompatibility. Among the technologies in which PPy has gained prominence are optoelectronics and solar energy conversion, where transparent electrodes such as fluorine-doped tin oxide (FTO) or indium tin oxide (ITO) are frequently used. However, FTO substrates have the notable advantage that their components are widely available in nature, unlike those of ITO. Recognizing the importance that the FTO/polypyrrole system has gained in various applications, here, we studied for the first time the nucleation and growth mechanism of electro-synthesized PPy on FTO. Additionally, the effect of the synthesis potential (0.9, 1.0, 1.1, and 1.2 V vs. Ag/AgCl) on the homogeneity, adhesion, conductivity, and HOMO energy levels of PPy films was determined. From current–time transients and scanning electron microscopy, it was found that films synthesized at 0.9 and 1.0 V exhibit 3D growth with progressive nucleation (as well as lower homogeneity and higher adhesion to FTO). In contrast, films synthesized at 1.1 and 1.2 V follow 2D growth with instantaneous nucleation. It was also evident that increasing the polymerization potential leads to polymers with lower conductivity and more negative HOMO levels (versus vacuum). These findings are relevant to encourage the use of electro-synthesized PPy in thin film applications that require a high control of material properties.