An efficient method to capture the impact of total knee replacement on a variety of simulated patient types: A finite element study

Stress distribution patterns during the gait cycle in patients with anterior femoral notching following total knee replacement

Background

Anterior femoral notching (AFN) is a severe complication of total knee replacement (TKR), which in a percentage of patients may lead to fractures after surgery. The purpose of this study was to investigate the stress distribution in patients with AFN and the safety depth of AFN during the gait cycle.

Methods

We performed a finite element (FE) analysis to analyse the mechanics around the femur during the gait cycle in patients with AFN. An adult volunteer was selected as the basis of the model. The TKR models were established in the 3D reconstruction software to simulate the AFN model during the TKR process, and the 1 mm, 2 mm, 3 mm, 4 mm, and 5 mm AFN models were established, after which the prosthesis was assembled. Three key points of the gait cycle (0°, 22°, and 48°) were selected for the analysis.

Results

The stress on each osteotomy surface was stable in the 0° phase. In the 22° phase, the maximum equivalent stress at 3 mm was observed. In the 48° phase, with the increase in notch depth, each osteotomy surface showed an overall increasing trend, the stress range was more extended, and the stress was more concentrated. Moreover, the maximum equivalent force value (158.3 MPa) exceeded the yield strength (115.1 MPa) of the femur when the depth of the notch was ≥ 3 mm.

Conclusions

During the gait cycle, if there is an anterior femoral cortical notch ≥ 3 mm, the stress will be significantly increased, especially at 22° and 48°. The maximum equivalent stress exceeded the femoral yield strength and may increase the risk of periprosthetic fractures.

Optimum stem length for mitigation of periprosthetic fracture risk following primary total knee arthroplasty: a finite element study

PURPOSE

Due to age-related changes to the material properties and thinning of the cortical bone structure, older patients with osteoporosis may be at greater risk of femoral fracture following total knee arthroplasty. This study investigates whether there is a potential role for stemmed prostheses in such scenarios to help mitigate peri-implant fracture risk, and if so what should the optimum stem length be to balance surgical bone loss with reduced fracture risk.

METHODS

Finite element models of the distal femur implanted with four different implant types: a posterior stabilising implant, a total stabilising implant with short stem (12 mm × 50 mm), a TS implant with medium stem (12 mm × 75 mm), and a TS implant with long stem (12 mm × 100 mm), were developed and analysed in this study. Osteoporotic properties were applied to the implanted femurs and the periprosthetic stresses and strains of each were recorded.

RESULTS

All stem lengths examined were found to lead to a reduction in periprosthetic stress in comparison with a primary stemless implant, with short-, medium-, and long-stemmed implants leading to an 11, 26, and 29% reduction in stress, respectively.

CONCLUSION

The results of this study show that periprosthetic stress and therefore fracture risk in old osteoporotic patients may be reduced through the use of stemmed femoral components. Of the three stems investigated, a medium-length stem is found to represent the best balance between bone preservation at the time of surgery and reduction in periprosthetic stress following implantation.

Computational modelling of motion at the bone-implant interface after total knee arthroplasty: The role of implant design and surgical fit

BACKGROUND

Aseptic loosening, osteolysis, and infection are the most commonly reported reasons for revision total knee arthroplasty (TKA). This study examined the role of implant design features (e.g. condylar box, pegs) and stems in resisting loosening, and also explored the sensitivity of the implants to a loose surgical fit due to saw blade oscillation.

METHODS

Finite element models of the distal femur implanted with four different implant types: cruciate retaining (CR), posterior stabilising (PS), total stabilising (TS) with short stem (12mm×50mm), and a total stabilising (TS) with long stem (19mm×150mm) were developed and analysed in this study. Two different fit conditions were considered: a normal fit, where the resections on the bone exactly match the internal profile of the implant, and a loose fit due to saw blade oscillation, characterised by removal of one millimetre of bone from the anterior and posterior surfaces of the distal femur. Frictional interfaces were employed at the bone-implant interfaces to allow relative motions to be recorded.

RESULTS

The results showed that interface motions increased with increasing flexion angle and loose fit. Implant design features were found to greatly influence the surface area under increased motion, while only slightly influencing the values of peak motion. Short uncemented stems behaved similarly to PS implants, while long canal filling stems exhibited the least amount of motion at the interface under any fit condition.

CONCLUSION

In conclusion, long stemmed prostheses appeared less susceptible to surgical cut errors than short stemmed and stemless implants.