Enhancing antifouling property of polysulfone ultrafiltration membrane by grafting zwitterionic copolymer via UV-initiated polymerization

Preparation and Adsorption Performance of Boron Adsorbents Derived from Modified Waste Feathers

This research focuses on modifying discarded feathers by grafting glycidyl methacrylate (GMA) onto their surface through thiolation, followed by an epoxy ring-opening reaction with N-methyl-D-glucamine (NMDG) to synthesize feather-based boron adsorbents. Optimization of the adsorbent preparation conditions was achieved through single-factor experiments, varying temperature, time, GMA concentration, and initiator dosage. The synthesized adsorbent (F-g-GMA-NMDG) underwent characterization using Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The adsorption behavior of the adsorbent was studied, and its boron adsorption capacity at different temperatures was determined through static adsorption kinetic curves. Analysis of adsorption isotherms, kinetics, and thermodynamics was conducted. Results indicate that the boron adsorption process by F-g-GMA-NMDG follows a pseudo-second-order model. The adsorption process is endothermic, with higher temperatures promoting adsorption efficiency. Gibbs free energy (ΔG) confirms the spontaneity of the adsorption process. Enhanced adsorption efficacy was observed under neutral and acidic pH conditions. After four cycles, the adsorbent maintained its adsorption efficiency, demonstrating its stability and potential for reuse. This study provides novel insights into both the treatment of discarded feathers and the development of boron adsorbents.

A Selective Separation Mechanism for Mono/divalent Cations and Properties of a Hollow-Fiber Composite Nanofiltration Membrane Having a Positively Charged Surface

Positively charged nanofiltration (NF) technology is considered a green and low-cost method for mono/divalent cation separation. Nevertheless, the separation rejection mechanisms of these NF membranes have yet to be extensively investigated. In this work, we fabricated a thin-film composite (TFC) hollow-fiber (HF) NF membrane with a positively charged surface via modification of the nascent interfacial polymerization layer using a branched polyethyleneimine (BPEI)/ethanol solution. Then, we extensively investigated its selective separation mechanism for mono/divalent cations. We proposed and proved that there exists a double-charged layer near the membrane surface, which helps to repel the divalent cations selectively via Donnan exclusion while promoting the fast penetration of monovalent cations. Meanwhile, the membrane skin layer is loose and hydrophilic due to the loose BPEI structure and the abundance of amine groups, as well as the changed fabrication conditions. In this way, we achieved very good mono/divalent cation selectivity and relatively high water permeance for the as-prepared HF NF membrane. We also obtained good anti-fouling, anti-scaling, and acid resistance, and long-term stability as well, which are urgently needed during practical application. Furthermore, we successfully amplified this HF NF membrane and proved that it has broad application prospects in mono/divalent cation separation.

Boron Adsorption Using NMDG-Modified Polypropylene Melt-Blown Fibers Induced by Ultraviolet Grafting

Boron is in high demand in many sectors, yet there are significant flaws in current boron resource utilization. This study describes the synthesis of a boron adsorbent based on polypropylene (PP) melt-blown fiber using ultraviolet (UV)-induced grafting of Glycidyl methacrylate (GMA) onto PP melt-blown fiber, followed by an epoxy ring-opening reaction with N-methyl-D-glucosamine (NMDG). Using single-factor studies, grafting conditions such as the GMA concentration, benzophenone dose, and grafting duration were optimized. Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD), and water contact angle were used to characterize the produced adsorbent (PP-g-GMA-NMDG). The PP-g-GMA-NMDG adsorption process was examined by fitting the data with different adsorption settings and models. The results demonstrated that the adsorption process was compatible with the pseudo-second-order model and the Langmuir model; however, the internal diffusion model suggested that the process was impacted by both extra- and intra-membrane diffusion. According to thermodynamic simulations, the adsorption process was exothermic. At pH 6, the greatest saturation adsorption capacity to boron was 41.65 mg·g^-1 for PP-g-GMA-NMDG. The PP-g-GMA-NMDG preparation process is a feasible and environmentally friendly route, and the prepared PP-g-GMA-NMDG has the advantages of high adsorption capacity, outstanding selectivity, good reproducibility, and easy recovery when compared to similar adsorbents, indicating that the reported adsorbent is promising for boron separation from water.

Preparation and performance of acrylic acid grafted PES ultrafiltration membrane via plasma surface activation

A modified PES ultrafiltration membrane with excellent separation and antifouling properties was obtained after modification by remote Ar–NH3 plasma-induced acrylic acid (AA) grafting. Hydrophilic properties were characterised using water contact angle measurements. The morphology was analysed using SEM and BET measurements. Changes in the surface functional groups were determined using XPS and ATR-FTIR. The separation and antifouling properties were evaluated through a bovine serum albumin (BSA) separation experiment. The results revealed that the surface structure of the modified membrane was not destroyed, that amino groups were introduced on the surface of the PES membrane, and that AA was successfully grafted. The water contact angle decreased from 67° in the original membrane to 5 ± 0.63° in the modified membrane. The water flux increased from 30 to 93.6 L/(m2·h). The rejection rate of BSA increased from 61.5 to 93.8%, and the flux recovery rate increased from 60.0 to 92.3%.

A Biofouling Resistant Zwitterionic Polysulfone Membrane Prepared by a Dual-Bath Procedure

This study introduces a zwitterionic material to modify polysulfone (PSf) membranes formed by a dual bath procedure, in view of reducing their fouling propensity. The zwitterionic copolymer, derived from a random polymer of styrene and 4-vinylpyrridine and referred to as zP(S-r-4VP), was incorporated to the PSf solution without any supplementary pore-forming additive to study the effect of the sole copolymer on membrane-structuring, chemical, and arising properties. XPS and mapping FT-IR provided evidence of the modification. Macrovoids appeared and then disappeared as the copolymer content increased in the range 1-4 wt%. The copolymer has hydrophilic units and its addition increases the casting solution viscosity. Both effects play an opposite role on transfers, and so on the growth of macrovoids. Biofouling tests demonstrated the efficiency of the copolymer to mitigate biofouling with a reduction in bacterial and blood cell attachment by more than 85%. Filtration tests revealed that the permeability increased by a twofold factor, the flux recovery ratio was augmented from 40% to 63% after water/BSA cycles, and irreversible fouling was reduced by 1/3. Although improvements are needed, these zwitterionic PSf membranes could be used in biomedical applications where resistance to biofouling by cells is a requirement.

Fouling Prevention in Polymeric Membranes by Radiation Induced Graft Copolymerization

The application of membrane processes in various fields has now undergone accelerated developments, despite the presence of some hurdles impacting the process efficiency. Fouling is arguably the main hindrance for a wider implementation of polymeric membranes, particularly in pressure-driven membrane processes, causing higher costs of energy, operation, and maintenance. Radiation induced graft copolymerization (RIGC) is a powerful versatile technique for covalently imparting selected chemical functionalities to membranes' surfaces, providing a potential solution to fouling problems. This article aims to systematically review the progress in modifications of polymeric membranes by RIGC of polar monomers onto membranes using various low- and high-energy radiation sources (UV, plasma, γ-rays, and electron beam) for fouling prevention. The feasibility of the modification method with respect to physico-chemical and antifouling properties of the membrane is discussed. Furthermore, the major challenges to the modified membranes in terms of sustainability are outlined and the future research directions are also highlighted. It is expected that this review would attract the attention of membrane developers, users, researchers, and scientists to appreciate the merits of using RIGC for modifying polymeric membranes to mitigate the fouling issue, increase membrane lifespan, and enhance the membrane system efficiency.

Anti-Biofouling Polymers with Special Surface Wettability for Biomedical Applications

The use of anti-biofouling polymers has widespread potential for counteracting marine, medical, and industrial biofouling. The anti-biofouling action is usually related to the degree of surface wettability. This review is focusing on anti-biofouling polymers with special surface wettability, and it will provide a new perspective to promote the development of anti-biofouling polymers for biomedical applications. Firstly, current anti-biofouling strategies are discussed followed by a comprehensive review of anti-biofouling polymers with specific types of surface wettability, including superhydrophilicity, hydrophilicity, and hydrophobicity. We then summarize the applications of anti-biofouling polymers with specific surface wettability in typical biomedical fields both in vivo and in vitro, such as cardiology, ophthalmology, and nephrology. Finally, the challenges and directions of the development of anti-biofouling polymers with special surface wettability are discussed. It is helpful for future researchers to choose suitable anti-biofouling polymers with special surface wettability for specific biomedical applications.

Surface Design of Liquid Separation Membrane through Graft Polymerization: A State of the Art Review

Surface modification of membranes is an effective approach for imparting unique characteristics and additional functionalities to the membranes. Chemical grafting is a commonly used membrane modification technique due to its versatility in tailoring and optimizing the membrane surface with desired functionalities. Various types of polymers can be precisely grafted onto the membrane surface and the operating conditions of grafting can be tailored to further fine-tune the membrane surface properties. This review focuses on the recent strategies in improving the surface design of liquid separation membranes through grafting-from technique, also known as graft polymerization, to improve membrane performance in wastewater treatment and desalination applications. An overview on membrane technology processes such as pressure-driven and osmotically driven membrane processes are first briefly presented. Grafting-from surface chemical modification approaches including chemical initiated, plasma initiated and UV initiated approaches are discussed in terms of their features, advantages and limitations. The innovations in membrane surface modification techniques based on grafting-from techniques are comprehensively reviewed followed by some highlights on the current challenges in this field. It is concluded that grafting-from is a versatile and effective technique to introduce various functional groups to enhance the surface properties and separation performances of liquid separation membranes.

Superwetting materials for hydrophilic-oleophobic membrane in oily wastewater treatment

The vast amount of oily wastewater released to the environment through industrialization has worsened the water quality in recent years, posing adverse impacts on general human health. Oil emulsified in water is one of the most difficult mixtures to be treated, making it imperative for new technology to be explored to address this issue. The use of conventional water treatment such as flotation, coagulation, precipitation, adsorption, and chemical treatment have low separation efficiencies and high energy costs, and are not applicable to the separation of oil/water emulsions. Therefore, there is a demand for more efficient methods and materials for the separations of immiscible oil/water mixtures and emulsions. Superwetting materials that can repel oil, while letting water pass through have been widely explored to fit into this concern. These materials usually make use of simultaneous hydrophilic/oleophobic mechanisms to allow a solid surface to separate oily emulsion with little to no use of energy. Also, by integrating specific wettability concepts with appropriate pore scale, solid surfaces may achieve separation of multifarious oil/water mixtures namely immiscible oil/water blends and consolidated emulsions. In this review, materials used to impart superwetting in solid surfaces by focusing on superhydrophilic/superoleophobic wetting properties of the materials categorized into fluorinated and non-fluorinated surface modification are summarized. In each material, its background, mechanism, fabricating processes, and their effects on solid surface's wetting capability are elaborated in detail. The materials reviewed in this paper are mainly organic and green, suggesting the alternative material to replace the fluorine group that is widely used to achieve oleophobicity in oily wastewater treatment.

Enhancing the antifouling property of polymeric membrane via surface charge regulation

In this study, positively charged monomers were grafted onto negatively charged membranes via UV radiation to improve the antifouling/antibiofouling properties of the polymeric membrane and the stability of the modification layer. The surface properties, morphologies, antifouling and antibiofouling properties, and stability of the modified membranes were systematically characterized. Results indicated that the introduction of [2-(methacryloyloxy) ethyl] trimethylammonium chloride (MTAC) monomers onto polyethersulfone (PES)/sulfonated polyethersulfone (SPES) membranes effectively increased the surface hydrophilicity. Meanwhile, the surfaces were neutralized with ~0 mV zeta potential in pH 3-10. Moreover, the formation of a polyampholytic copolymer and the antibacterial ability of MTAC considerably improved the antibiofouling properties of the modified membranes. The MTAC-grafted PES/SPES membranes showed excellent antifouling/antibiofouling properties during the treatment of various types of wastewater, including bovine serum albumin solution, oil/water emulsion, and bacterial suspension. Therefore, this study provides a simple and effective method of constructing stable and antifouling membranes for sustainable water treatment.

Wetting Transition of Ionic Substrate by Modulating Surface Charge Distribution

Surface wettability regulation plays a crucial role in antifouling and related applications. For regulating surface wettability, one of the effective approaches is to modulate the surface charge distribution. Herein, we report a theoretical study for unraveling the mechanistic relation between surface charge distribution and ionic substrate wettability. Specifically, acetonitrile liquids at ambient condition in contact with various ionic substrates are considered. At different surface charge distributions, the interfacial thermodynamic properties are investigated by means of molecular density functional theory. We find that the variation of the spatial interval among the discrete charges strongly alters the substrate-acetonitrile interaction and leads to an oscillation in the interfacial tension, indicating that the substrate can be tuned from a solvophobic one to a solvophilic one. This trend can be further enhanced by increasing the charge quantity. The underlying mechanisms are extensively discussed and expatiated. Our work provides theoretical guidance to engineer and regulate surface wettability.

Recent Development of Polyolefin-Based Microporous Separators for Li-Ion Batteries: A Review

Secondary Li-ion batteries have been paid attention to wide-range applications of power source for the portable electronics, electric vehicle, and electric storage reservoir. Generally, lithium-ion batteries are comprised of four components including anode, cathode, electrolyte and separator. Although separators do not take part in the electrochemical reactions in a lithium-ion (Li-ion) battery, they conduct the critical functions of physically separating the positive and negative electrodes to prevent electrical short circuit while permitting the free flow of lithium ions through the liquid electrolyte that fill in their open porous structure. Hence, the separator is directly related to the safety and the power performance of the battery. Among a number of separators developed thus far, polyethylene (PE) and polypropylene (PP) porous membrane separators have been the most dominant ones for commercial Li-ion batteries over the decades because of their superior properties such as cost-efficiency, good mechanical strength and pore structure, electrochemical stability, and thermal shutdown properties. However, there are main issues for vehicular storage, such as nonpolarity, low surface energy and poor thermal stability, although the polyolefin separators have proven dependable in portable applications. Hence, in this review, we decide to provide an overview of the types of polyolefin microporous separators utilized in Li-ion batteries and the methods employed to modify their surface in detail. The remarkable results demonstrate that extraordinary properties can be exhibited by mono- and multilayer polyolefin separators if they are modified using suitable methods and materials.

Nano/microplastics in water and wastewater treatment processes - Origin, impact and potential solutions

The presence of nano and microplastics in water has increasingly become a major environmental challenge. A key challenge in their detection resides in the relatively inadequate analytical techniques available preventing deep understanding of the fate of nano/microplastics in water. The occurrence of nano/microplastics in water and wastewater treatment plants poses a concern for the quality of the treated water. Due to their broad but small size and diverse chemical natures, nano/microplastics may travel easily along water and wastewater treatment processes infiltrating remediation processes at various levels, representing operational and process stability challenges. This review aims at presenting the current understanding of the fate and impact of nano/microplastics through water and wastewater treatment plants. The formation and fragmentation mechanisms, physical-chemical properties and occurrence of nano/microplastics in water are correlated to the interactions of nano/microplastics with water and wastewater treatment plant processes and potential solutions to limit these interactions are comprehensively reviewed. This critical analysis offers new strategies to limit the number of nano/microplastics in water and wastewater to keep water quality up to the required standards and reduce threats on our ecosystems.

Toward Antibiofouling PVDF Membranes

Membranes for biologically and biomedically related applications must be bioinert, that is, resist biofouling by proteins, human cells, bacteria, algae, etc. Hydrophobic materials such as polysulfone, polypropylene, or poly(vinylidene fluoride) (PVDF) are often chosen as matrix materials but their hydrophobicity make them prone to biofouling, which in turn limits their application in biological/biomedical fields. Here, we designed PVDF-based membranes by precipitation from the vapor phase and zwitterionized them in situ to reduce their propensity to biofouling. To achieve this goal, we used a copolymer containing phosphorylcholine groups. An in-depth physicochemical characterization revealed not only the controlled presence of the copolymer in the membrane but also that bicontinuous membranes could be formed. Membrane hydrophilicity was greatly improved, resulting in the mitigation of a variety of biofoulants: the attachment of Stenotrophomonas maltophilia, Streptococcus mutans, and platelets was reduced by 99.9, 99.9, and 98.9%, respectively. Besides, despite incubation in a plasma platelet-poor medium, rich in plasma proteins, a flux recovery ratio of 75% could be measured while it was only 40% with a hydrophilic commercial membrane of similar structure and physical properties. Similarly, the zwitterionic membrane severely mitigated biofouling by microalgae during their harvesting. All in all, the material/process combination presented in this work leads to antibiofouling porous membranes with a large span of potential biomedically and biologically related applications.

Physical Processes in Polymeric Filters Used for Dialysis

The key physical processes in polymeric filters used for the blood purification include transport across the capillary wall and the interaction of blood cells with the polymer membrane surface. Theoretical modeling of membrane transport is an important tool which provides researchers with a quantification of the complex phenomena involved in dialysis. In the paper, we present a dense review of the most successful theoretical approaches to the description of transport across the polymeric membrane wall as well as the cell⁻polymer surface interaction, and refer to the corresponding experimental methods while studying these phenomena in dialyzing filters.

Designs of Zwitterionic Interfaces and Membranes

Zwitterionic materials are the latest generation of materials for nonfouling interfaces and membranes. They outperform poly(ethylene glycol) derivatives because they form tighter bonds with water molecules and can trap more water molecules. This feature article summarizes our laboratory's fundamental developments related to the functionalization of interfaces and membranes using zwitterionic materials. Our molecular designs of zwitterionic polymers and copolymers, sulfobetaine-based, carboxybetaine-based, or phosphobetaine-based, are first reviewed. Then, the strategies used to functionalize surfaces/membranes by coating, grafting onto, grafting from, or in situ modification are examined and discussed, and the third part of this article shifts the focus to key applications of zwitterionic materials. Finally, some potential future directions for molecular designs, functionalization processes, and applications are presented.

Preparation and characterization of PSF/PEI/CaCO3 nanocomposite membranes for oil/water separation

Ultrafiltration (UF) is one of the significant advanced processes for oily wastewater treatment due to its clear advantages, for instance, ease in operation and efficient separation. The main drawback of these processes is the fouling problem and many researchers' effort on fabrication of high-performance membranes with higher hydrophilicity and antifouling properties. In this study, flat-sheet polysulfone (PSF)/polyethylenimine (PEI)/CaCO₃ nanocomposite membranes were prepared by phase inversion method for oil/water emulsion separation. Structural properties of membranes were characterized by SEM, FT-IR, contact angle, tensile strength, and atomic force microscopy analysis. Increasing the CaCO₃ nanoparticle loading exhibited the increased the water flux and BSA rejection. PSF/PEI/10 wt% CaCO₃ nanocomposite membranes have 145 L/m² h water flux at 2 bar with a contact angle of 84° and with 92% BSA rejection. All prepared CaCO₃ nanocomposite membranes reached similar oil rejections at above 90%. Besides the higher water flux and oil removal efficiencies, 10 wt% of CaCO₃ nanoparticle-blended PSF membranes has notable antifouling capacity with the highest flux recovery ratio (FRR) and lowest flux decay ratio (DR) values. The results showed that there is a great potential to use PSF/PEI/CaCO₃ nanocomposite membranes for the treatment of oil water emulsions with higher permeability and antifouling capacity.