Polymerization mechanism for radiation-induced grafting of styrene into alicyclic polyimide films for preparation of polymer electrolyte membranes

A Facile Way to Fabricate GO-EDA/Al2O3 Tubular Nanofiltration Membranes with Enhanced Desalination Stability via Fine-Tuning the pH of the Membrane-Forming Suspensions

Pristine graphene oxide (GO)-based membranes have proven promising for molecular and ion separation owing to efficient molecular transport nanochannels, but their separation ability in an aqueous environment is limited by the natural swelling tendency of GO. To obtain a novel membrane with anti-swelling behavior and remarkable desalination capability, we used the Al₂O₃ tubular membrane with an average pore size of 20 nm as the substrate and fabricated several GO nanofiltration ceramic membranes with different interlayer structures and surface charges by fine-tuning the pH of the GO-EDA membrane-forming suspension (pH = 7, 9, 11). The resultant membranes could maintain desalination stability, whether immersed in water for 680 h or operated under a high-pressure environment. When the pH of the membrane-forming suspension was 11, the prepared GE-11 membrane showed a rejection of 91.5% (measured at 5 bar) towards 1 mM Na₂SO₄ after soaking in water for 680 h. An increase in the transmembrane pressure to 20 bar resulted in an increase in the rejection towards the 1 mM Na₂SO₄ solution to 96.3%, and an increase in the permeance to 3.7 L·m^-2·h^-1·bar^-1. The proposed strategy in varying charge repulsion is beneficial to the future development of GO-derived nanofiltration ceramic membranes.

Non-Fluorinated Polymer Composite Proton Exchange Membranes for Fuel Cell Applications - A Review

The critical component of a proton exchange membrane fuel cell (PEMFC) system is the proton exchange membrane (PEM). Perfluorosulfonic acid membranes such as Nafion are currently used for PEMFCs in industry, despite suffering from reduced proton conductivity due to dehydration at higher temperatures. However, operating at temperatures below 100 °C leads to cathode flooding, catalyst poisoning by CO, and complex system design with higher cost. Research has concentrated on the membrane material and on preparation methods to achieve high proton conductivity, thermal, mechanical and chemical stability, low fuel crossover and lower cost at high temperatures. Non-fluorinated polymers are a promising alternative. However, improving the efficiency at higher temperatures has necessitated modifications and the inclusion of inorganic materials in a polymer matrix to form a composite membrane can be an approach to reach the target performance, while still reducing costs. This review focuses on recent research in composite PEMs based on non-fluorinated polymers. Various inorganic fillers incorporated in the PEM structure are reviewed in terms of their properties and the effect on PEM fuel cell performance. The most reliable polymers and fillers with potential for high temperature proton exchange membranes (HTPEMs) are also discussed.

High Performance Soluble Polyimides from Ladder-Type Fluorinated Dianhydride with Polymorphism

A novel rigid semi-alicyclic dianhydride 9,10-difluoro-9,10-bis(trifluoromethyl)-9,10-dihydroanthracene-2,3,6,7-tetracarboxylic acid dianhydride (8FDA) was reported, and its single crystal X-ray diffraction result revealed the existence of the polymorphic structure in this compound. The detail geometric configuration transition during the synthesized process was investigated, exhibiting a transition of from trans- to cis- when the hydroxyl groups were substituted by fluoride with diethylaminosulfur trifluoride (DAST). Compared with the dianhydride 4,4'-(Hexaflouroisopropylidene) diphthalic anhydride (6FDA) and 1S,2R,4S,5R-cyclohexanetetracarboxylic dianhydride (HPMDA), the resulting polyimide (PI) films based on 8FDA exhibited an obviously higher glass transition temperature (Tg, 401 °C) and a much lower coefficient of thermal expansion (CTE, 14 ppm K-1). This indicates that 8FDA is an ideal building block in high-performance soluble PIs with low CTE.