Polyethylene glycol cross-linked sulfonated polyethersulfone based filtration membranes with improved antifouling tendency

Fabrication of Ti2SnC-MAX Phase Blended PES Membranes with Improved Hydrophilicity and Antifouling Properties for Oil/Water Separation

In this research work, the Ti₂SnC MAX phase (MP) was synthesized via the reactive sintering procedure. The layered and crystalline structure of this MP was verified by SEM, HRTEM, and XRD analyses. This nano-additive was used for improvement of different features of the polyethersulfone (PES) polymeric membranes. The blended membranes containing diverse quantities of the MP (0-1 wt%) were fabricated by a non-solvent-induced phase inversion method. The asymmetric structure of the membranes with small holes in the top layer and coarse finger-like holes and macro-voids in the sublayer was observed by applying SEM analysis. The improvement of the membrane's hydrophilicity was verified via reducing the contact angle of the membranes from 63.38° to 49.77° (for bare and optimum membranes, respectively). Additionally, in the presence of 0.5 wt% MP, the pure water flux increased from 286 h to 355 L/m² h. The average roughness of this membrane increased in comparison with the bare membrane, which shows the increase in the filtration-available area. The high separation efficiency of the oil/water emulsion (80%) with an improved flux recovery ratio of 65% was illustrated by the optimum blended membrane.

Water Treatment Using High Performance Antifouling Ultrafiltration Polyether Sulfone Membranes Incorporated with Activated Carbon

Membrane fouling is a continued critical challenge for ultrafiltration membranes performance. In this work, polyether sulfone (PES) ultrafiltration (UF) membranes were fabricated via phase-inversion method by incorporating varying concentrations of APTMS modified activated carbon (mAC). The mAC was thoroughly characterized and the fabricated membranes were studied for their surface morphology, functional groups, contact angle, water retention, swelling (%) porosity, and water flux. The hydrophilicity of mAC membranes also resulted in lower contact angle and higher values of porosity, roughness, water retention as well as water flux. Also, the membranes incorporated with mAC exhibited antibacterial performance against model test strains of gram-negative Ecoil and gram-positive S. aureus. The antifouling studies based on bovine serum albumin protein (BSA) solution filtration showed that mAC membranes have better BSA flux. The higher flux and antifouling characteristics of the mAC membranes were attributed to the electrostatic repulsion of the BSA protein from the unique functional properties of AC and network structure of APTMS. The novel mAC ultrafiltration membranes developed and studied in present work can provide higher flux and less BSA rejection thus can find antifouling applications for the isolation and concentration of proteins and macromolecules.

Zwitterionic silica nanogel-modified polysulfone nanoporous membranes formed by in-situ method for water treatment

We report a simple methodology to prepare nano-porous polysulfone membranes using zwitterionic functionalized silica nanogels with high BSA protein rejection and antifouling properties. The zwitterionic silica precursor was prepared by reacting 1,3-propane sultone with 3-aminopropyl triethoxysilane under an inert atmosphere. The precursor was in situ hydrolyzed and condensed in the polysulfone nanoporous membrane network by one-pot acidic phase inversion. The prepared membranes were characterized to establish their physicochemical nature, morphology, and basic membrane properties such as permeation, rejection, and recovery. The zwitterionic membranes showed improved hydrophilicity, membrane water uptake (∼83.5%), water permeation, BSA protein rejection (>95%), and dye rejection (congo red: >52% (∼6-fold increase); methylene blue: ∼15% (∼2-fold increase)) were improved without compromising the membrane flux and fouling resistance. Overall, we report an easy fabrication method of efficient nanocomposite zwitterionic ultrafilter membranes for water treatment with excellent flux, protein separation, filtration efficiency, and antifouling behavior.

Ultralow-Fouling Zwitterionic Polyurethane-Modified Membranes for Rapid Separation of Plasma from Whole Blood

The separation of plasma from blood cells in whole blood is an essential step for many diagnostic and therapeutic applications. However, the current point-of-care plasma separation approaches have not yet satisfied the need for a rapid, high-flux, and low-cost process. Here, we report a portable, low-cost, disposable membrane-based plasma separation device that enables rapid plasma extraction from whole blood. Rapid separation of plasma can be obtained with a simple three-step operation: blood injection, separation, and plasma collection. Our device benefits from the zwitterionic polyurethane-modified cellulose acetate (PCBU-CA) membrane, which can greatly inhibit the surface fouling of blood cells and membrane flux decline. The zwitterionic coating is stable on the membrane surface during blood filtration and leads to a 60% decrease in surface fibrinogen adsorption than a nonmodified membrane surface. The ultralow-blood-fouling properties of the PCBU-CA membrane enable rapid, continuous separation of plasma: within 10 min, the device can yield 0.5-0.7 mL of plasma from 10 mL of whole blood. The extracted plasma is verified as cell-free, exhibits a low hemoglobin level, and has a high protein recovery. Our PCBU-CA membrane provides a pathway for developing a high-efficiency portable plasma separation device that can reduce the time to diagnosis, allow effective patient care, and eventually reduce hospital costs.

Fabrication of Zwitterion TiO2 Nanomaterial-Based Nanocomposite Membranes for Improved Antifouling and Antibacterial Properties and Hemocompatibility and Reduced Cytotoxicity

Although zwitterion nanomaterials exhibit outstanding antifouling property, hemocompatibility, and antibacterial activity, their poor solubility in organic solvents limits their practical applications. In the present study, natural lysine (amino acids) was surface-grafted onto one-dimensional (1D) TiO2 nanofibers (NFs) through an epoxy ring opening in which the 3-glycidyloxypropyl (dimethoxy) methyl silane was used as a coupling agent. Chemical binding and morphological studies, such as Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and transmission electron microscopy, were conducted to confirm the successful grafting of lysine onto the TiO2 NFs. The lysine-grafted TiO2 NF-polyethersulfone (PES) membrane induced electrostatic interactions and increased the surface charges from -28 to 16 mV in ζ-potential analysis. The lysine exhibited zwitterion characteristics owing to the presence of amino (cations) and carboxyl (anions) functional groups. Moreover, the modified TiO2-PES zwitterion membranes exhibited good water flux performances compared to the pristine membrane. ZT-4 membrane displayed the highest water fluxand bovine serum albumin (BSA) rejection of 137 ± 1.8 L m-2 h-1 and 94 ± 1%, respectively. The cell viability results revealed that the zwitterion PES membrane had excellent biocompatibility with peripheral blood mononuclear cells. The present work offers a convenient strategy to improve the hydrophilicity, antifouling property, and hemocompatibility of modified TiO2-PES zwitterion membranes for their biomedical and blood-contacting applications such as hemodialysis.

Antimicrobial surfaces: a review of synthetic approaches, applicability and outlook

The rapid spread of microorganisms such as bacteria, fungi, and viruses can be extremely detrimental and can lead to seasonal epidemics or even pandemic situations. In addition, these microorganisms may bring about fouling of food and essential materials resulting in substantial economic losses. Typically, the microorganisms get transmitted by their attachment and growth on various household and high contact surfaces such as doors, switches, currency. To prevent the rapid spread of microorganisms, it is essential to understand the interaction between various microbes and surfaces which result in their attachment and growth. Such understanding is crucial in the development of antimicrobial surfaces. Here, we have reviewed different approaches to make antimicrobial surfaces and correlated surface properties with antimicrobial activities. This review concentrates on physical and chemical modification of the surfaces to modulate wettability, surface topography, and surface charge to inhibit microbial adhesion, growth, and proliferation. Based on these aspects, antimicrobial surfaces are classified into patterned surfaces, functionalized surfaces, superwettable surfaces, and smart surfaces. We have critically discussed the important findings from systems of developing antimicrobial surfaces along with the limitations of the current research and the gap that needs to be bridged before these approaches are put into practice.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s10853-021-06404-0.

Surface Antifouling Modification on Polyethylene Filtration Membranes by Plasma Polymerization

Surface modification on microporous polyethylene (PE) membranes was facilitated by plasma polymerizing with two hydrophilic precursors: ethylene oxide vinyl ether (EO1V) and diethylene oxide vinyl ether (EO2V) to effectively improve the fouling against mammalian cells (Chinese hamster ovary, CHO cells) and proteins (bovine serum albumin, BSA). The plasma polymerization procedure incorporated uniform and pin-hole free ethylene oxide-containing moieties on the filtration membrane in a dry single-step process. The successful deposition of the plasma polymers was verified by Fourier-transform infrared (FTIR), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) analyses. Water contact angle measurements and permeation experiments using cell and protein solutions were conducted to evaluate the change in hydrophilicity and fouling resistance for filtrating biomolecules. The EO1V and EO2V plasma deposited PE membranes showed about 1.45 fold higher filtration performance than the pristine membrane. Moreover, the flux recovery reached 80% and 90% by using deionized (DI) water and sodium hydroxide (NaOH) solution, indicating the efficacy of the modification and the good reusability of the modified PE membranes.

Antifouling Membranes Prepared from Polyethersulfone Grafted with Poly(ethylene glycol) Methacrylate by Radiation-Induced Copolymerization in Homogeneous Solution

To synthesize evenly grafted copolymers, gamma radiation of homogeneous solutions was employed to graft poly(ethylene glycol) methacrylate (PEGMA) onto polyethersulfone (PES). The grafting was verified by Fourier transform infrared spectroscopy, and the degrees of grafting (DGs) were determined by elementary analysis. The PES-g-polyPEGMA copolymers with different DGs were obtained by changing the monomer concentration. Membranes were cast from pristine PES, PES/PEG blends, and PES-g-polyPEGMA with different DGs, respectively, via nonsolvent-induced phase separation. Results from water contact angle measurements and scanning electron microscopy analysis indicated that increasing DGs led to PES-g-polyPEGMA membranes with increasing hydrophilicity and porousness. Filtration experimental results showed that increasing DGs without adding pore-forming agents caused PES-g-polyPEGMA membranes with higher permeability. Compared with PES/PEG membranes with analogous permeation characteristics, in which PEG is added as a pore-forming agent, PES-g-polyPEGMA membranes exhibited superior antifouling properties.

Designs of Zwitterionic Interfaces and Membranes

Zwitterionic materials are the latest generation of materials for nonfouling interfaces and membranes. They outperform poly(ethylene glycol) derivatives because they form tighter bonds with water molecules and can trap more water molecules. This feature article summarizes our laboratory's fundamental developments related to the functionalization of interfaces and membranes using zwitterionic materials. Our molecular designs of zwitterionic polymers and copolymers, sulfobetaine-based, carboxybetaine-based, or phosphobetaine-based, are first reviewed. Then, the strategies used to functionalize surfaces/membranes by coating, grafting onto, grafting from, or in situ modification are examined and discussed, and the third part of this article shifts the focus to key applications of zwitterionic materials. Finally, some potential future directions for molecular designs, functionalization processes, and applications are presented.

A substrate-independent ultrathin hydrogel film as an antifouling and antibacterial layer for a microfiltration membrane anchored via a layer-by-layer thiol-ene click reaction

Herein, a substrate-independent ultrathin hydrogel film was constructed on a microfiltration membrane through layer-by-layer (LbL) thiol-ene click chemistry to improve the antifouling and antibacterial properties. In our strategy, ene-functionalized dopamine was synthesized and coated onto a model substrate (polyethersulfone membrane) to introduce double bonds as anchoring sites for the hydrogel film; thiol-functionalized poly[oligo(ethylene glycol)mercaptosuccinate] (POEGMS) and ene-functionalized P(SBMA-co-AA) were synthesized as hydrogel precursors. The membrane was alternately immersed in the precursor solutions to form the ultrathin hydrogel film. Finally, Ag nanoparticles (AgNPs) were loaded into the hydrogel layer by adsorption and reduction procedures. By coating the hydrogel films, the loaded AgNPs could kill almost all the contacting bacteria and the bacteria in the surroundings, and the enhanced hydrophilicity of the modified membrane could effectively prevent the attachment of the bacteria. The membrane flux showed no significant decrease, the rejection ratio of BSA increased from 51% to 89%, and the F_RR increased from 36% to 90%. Moreover, the improvement of the hemocompatibility was confirmed by the decline in the plasma protein adsorption, prolonged clotting times, low hemolysis ratio, and prevention of platelet adhesion. Compared with that of other techniques for attaching hydrogel films, the main advantage of the current technique is that the hydrogel film thickness could be well controlled within the nanometer range; thus, it could significantly improve the antifouling and antibacterial properties of the membrane, but without compromising its permeability. Another advantage is that it is versatile for various substrates such as PVDF, PAN, and CA. This study opens up a facile and versatile route for anchoring ultrathin hydrogel film onto polymeric membranes to achieve excellent antifouling, antibacterial and hemocompatible properties.

Highly fouling-resistant brominated poly(phenylene oxide) membranes using surface grafted diethylenetriamine

Composite BPPO/DETA ultrafiltration membranes show decreased membrane fouling and enhanced protein rejection with very high flux recovery ratios.

Zwitterionic fibrous polypropylene assembled with amphiphatic carboxybetaine copolymers for hemocompatible blood filtration

The present study serves three main functions. First, it presents a novel random copolymer, made of octadecyl acrylate hydrophobic blocks and 2-(dimethylamino)ethyl methacrylate hydrophilic groups, and it zwitterionic form. Second, random copolymer and zwitterionic random copolymer, OmDn and Z-OmDn, are used to modify polypropylene membranes by evaporation coating. Our investigations unveil that this method leads to sufficiently stable self-assembling provided a minimum number of hydrophobic repeat units of 77, which also corresponds to a hydrophobic degree of 74%. Third, antifouling and hemocompatible properties of membranes are thoroughly investigated using all types of blood cells separately, as well as challenging membranes against whole blood in static and dynamic conditions. Membranes modified with zwitterionic copolymer containing 26% of zwitterionic groups are shown to be highly antifouling and hemocompatible, for a coating density as low as 0.2mg/cm(2). Their application in a specially designed blood filtration module enabled to almost totally inhibit blood cells interactions with membrane material, as well as to importantly reduce platelet activation in the permeate (2.5-fold reduction).

STATEMENT OF SIGNIFICANCE

The design of new zwitterionic copolymer material is proposed and demonstrated in this study. It was showed that hydrophobicoctadecyl acrylate segments can be introduced in the zwitterioniccarboxybetaine polymer chain with a well-controlled random sequence. Stable, efficient, and effective surface zwitterionization of hydrophobic polypropylene are obtained via grafting onto approach by evaporation-induced self-assembling coating. In the perspective of potential application, hemocompatible blood filtration was demonstrated with the excellent results of non-activated platelets obtained.

SUMMARY OF IMPACTS

DESIGN

New zwitterionicmaterial, amphiphatic carboxybetaine copolymers.

DEVELOPMENT

Evaporation-induced self-assembling grafting.

APPLICATION

Hemocompatible blood filtration.

Fabrication and evaluation of polymeric membranes for blood dialysis treatments using functionalized MWCNT based nanocomposite and sulphonated-PES

The use of polyethersulfone based membranes for dialysis therapy is increasing, but the poor bio-compatibility of the PES membrane can raise severe blood reactions affecting the rate of morbidity and mortality of hemodialysis (HD) patients.

Enhanced hydrophilic and antifouling polyacrylonitrile membrane with polydopamine modified silica nanoparticles

Hydrophilic and antifouling polydopamine modified silica nanoparticles-polyacrylonitrile membranes were fabricated for water purification applications. High dispersion and better compatibility of modified nanoparticles with polyacrylonitrile was observed.

Layer by layer assembly of sulfonic poly(ether sulfone) as heparin-mimicking coatings: scalable fabrication of super-hemocompatible and antibacterial membranes

In this study, super-hemocompatible and antibacterial polymeric membranes with surface coated nanofilms were fabricated by LBL assembly of water-soluble heparin-mimicking polymer and quaternized chitosan.

Ag-nanogel blended polymeric membranes with antifouling, hemocompatible and bactericidal capabilities

A highly efficient, universal and convenient protocol is reported to fabricate antifouling, hemocompatible, and bactericidal membranes by physically blending of antifouling nanogels and in situ silver nanoparticles immobilization.