Fabrication of novel poly(m-phenylene isophthalamide) hollow fiber nanofiltration membrane for effective removal of trace amount perfluorooctane sulfonate from water

Perfluorooctanoic acid-contaminated wastewater treatment by forward osmosis: Performance analysis

Perfluorooctanoic acid (PFOA) is a persistent compound, raising considerable global apprehension due to its resistance to breakdown and detrimental impacts on human health and aquatic environments. Pressure-driven membrane technologies treating PFAS-contaminated water are expensive and prone to fouling. This study presented a parametric investigation of the effectiveness of cellulose triacetate membrane in the forward osmosis (FO) membrane for removing PFOA from an aqueous solution. The study examined the influence of membrane orientation modes, feed pH, draw solution composition and concentration, and PFOA concentration on the performance of FO. The experimental results demonstrated that PFOA rejection was 99 % with MgCl2 and slightly >98 % with NaCl draw solutions due to the mechanism of PFOA binding to the membrane surface through Mg2+ ions. This finding highlights the crucial role of the draw solution's composition in PFOA treatment. Laboratory results revealed that membrane rejection of PFOA was 99 % at neutral and acidic pH levels but decreased to 95 % in an alkaline solution at pH 9. The decrease in membrane rejection is attributed to the dissociation of the membrane's functional groups, consequently causing pore swelling. The results were confirmed by calculating the average pore radius of the CTA membrane, which increased from 27.94 nm at pH 5 to 30.70 nm at pH 9. Also, variations in the PFOA concentration from 5 to 100 mg/L did not significantly impact the membrane rejection, indicating the process's capability to handle a wide range of PFOA concentrations. When seawater was the draw solution, the FO membrane rejected 99 % of PFOA concentrations ranging from 5 mg/L to 100 mg/L. The CTA FO treating PFOA-contaminated wastewater from soil remediation achieved a 90 % recovery rate and water flux recovery of 96.5 % after cleaning with DI water at 40 °C, followed by osmotic backwash. The results suggest the potential of using abundant and cost-effective natural solutions in the FO process, all without evident membrane fouling.

A Comprehensive Review of Hollow-Fiber Membrane Fabrication Methods across Biomedical, Biotechnological, and Environmental Domains

This work presents methods of obtaining polymeric hollow-fiber membranes produced via the dry-wet phase inversion method that were published in renowned specialized membrane publications in the years 2010-2020. Obtaining hollow-fiber membranes, unlike flat membranes, requires the use of a special installation for their production, the most important component of which is the hollow fiber forming spinneret. This method is most often used in obtaining membranes made of polysulfone, polyethersulfone, polyurethane, cellulose acetate, and its derivatives. Many factors affect the properties of the membranes obtained. By changing the parameters of the spinning process, we change the thickness of the membranes' walls and the diameter of the hollow fibers, which causes changes in the membranes' structure and, as a consequence, changes in their transport/separation parameters. The type of bore fluid affects the porosity of the inner epidermal layer or causes its atrophy. Porogenic compounds such as polyvinylpyrrolidones and polyethylene glycols and other substances that additionally increase the membrane porosity are often added to the polymer solution. Another example is a blend of two- or multi-component membranes and dual-layer membranes that are obtained using a three-nozzle spinneret. In dual-layer membranes, one layer is the membrane scaffolding, and the other is the separation layer. Also, the temperature during the process, the humidity, and the composition of the solution in the coagulating bath have impact on the parameters of the membranes obtained.

A novel ZIF-L/PEI thin film nanocomposite membrane for removing perfluoroalkyl substances (PFASs) from water: Enhanced retention and high flux

Membrane separation technology is widely recognized as an effective method for removing perfluoroalkyl substances (PFASs) in water treatment. ZIF-L, a metal-organic framework (MOF) family characterized by its mat-like cavities and leaf-like morphology, has garnered considerable interest and has been extensively employed in fabricating thin-film nanocomposite (TFN) membranes. In this study, a robust, high-performance TFN membrane to remove PFASs in a nanofiltration (NF) process was created through an interfacial polymerization approach on the surface of polysulfone (PSF), incorporating ZIF-L within the selective layer. The TFN membrane modified by adding 5 wt% ZIF-L (relative to the weight of ethylene imine polymer (PEI)) exhibits 2.3 times higher water flux (up to 47.56 L·m-2·h-1·bar-1) than the pristine thin film composite membrane (20.46 L·m-2·h-1·bar-1), and the rejection for typical PFASs were above 95 % (98.47 % for perfluorooctanesulfonic acid (PFOS) and 95.85 % for perfluorooctanoic acid (PFOA)). The effectiveness of the ZIF-L/PEI TFN membrane in retaining representative PFASs was examined under various conditions, including different pressures, feed concentrations, aqueous environments, and salt ions. Notably, the experiments demonstrated that even after contamination with humic acid (HA), >88 % of the water flux could be restored by washing. Additionally, density functional theory (DFT) calculations were employed to predict the distinct intermolecular interactions between PFASs and ZIF-L as well as PEI. These calculations provide additional insights into the interception mechanism of TFN membranes towards PFASs. Based on this study, TFN membranes incorporating MOF as nanofillers show great potential as an effective method for purifying PFASs from aqueous environments and possess superior environmental sustainability and cost-effectiveness.

Removal of per- and polyfluoroalkyl substances by nanofiltration: Effect of molecular structure and coexisting natural organic matter

This study investigates the removal efficiency of anionic, cationic, and zwitterionic per- and polyfluoroalkyl substances (PFAS) by nanofiltration (NF) in the presence of three representative natural organic matter (NOM) types: bovine serum albumin (BSA), humic acid (HA), and sodium alginate (SA). In particular, effects of PFAS molecular structure and coexisting NOM on the transmission and adsorption efficiency of PFAS during NF treatment were analyzed. The results indicate that NOM types dominate membrane fouling behavior despite the coexistence of PFAS. SA exhibits the most significant fouling propensity, resulting in maximum water flux decline. NF effectively removed both ether and precursor PFAS. The effects of the three typical NOM on the membrane-passing behavior of PFAS were consistent for all PFAS investigated. Generally, PFAS transmission decreased in the order of SA-fouled > pristine > HA-fouled > BSA-fouled, indicating that the presence of HA and BSA enhanced PFAS removal while SA declined. Furthermore, reduced PFAS transmission was observed with increased perfluorocarbon chain length or molecular weight (MW), regardless of the presence or type of the NOM. The impacts of NOM on PFAS filtration diminished when the PFAS van der Waals radius was > 4.0 Å, MW > 500 Da, polarization > 20 Å, or LogKow > 3. These findings suggest that both steric repulsion and hydrophobic interactions, especially the former, play important roles in PFAS rejection by NF. This study provides insights into the specific applicability and performance of membrane-based processes for eliminating PFAS during drinking and wastewater treatments, and highlighting the importance of coexisting NOM.

Preparation of hollow-fiber nanofiltration membranes of high performance for effective removal of PFOA and high resistance to BSA fouling

Nanofiltration (NF) process has become one of the most promising technologies to remove micro-organic combined water pollution. Developing a NF membrane material with efficient separation for perfluorooctanoic acid (PFOA) combined pollution is highly desired, this manuscript targets this unmet need specifically. In this work, hydrophilic SiO₂ nanoparticles with various contents blended with carboxylic multiwalled carbon nanotube were used to modify poly (m-phenylene isophthal amide) (SiO₂/CMWCNT/PMIA) hollow fiber NF membrane. The modified membrane with 0.1 wt% SiO₂ doping exhibits way better fouling resistance with irreversible fouling ratio decreased dramatically from 18.7% to 2.3%, and the recovery rate of water flux increases significantly from 81.2% to 97.7%. The separation experiment results had confirmed that the modified membrane could improve the rejection from 97.2% to 98.6% for perfluorooctanoic acid (PFOA) and its combined pollution with bovine serum albumin (BSA). It is clear that this reported SiO₂/CMWCNT/PMIA hollow fiber NF membrane potentially could be applied in water treatment. This research also provides a theoretical basis for efficiently removal of PFOA and its combined pollution by NF membrane.

A Review on Removal and Destruction of Per- and Polyfluoroalkyl Substances (PFAS) by Novel Membranes

Per- and Polyfluoroalkyl Substances (PFAS) are anthropogenic chemicals consisting of thousands of individual species. PFAS consists of a fully or partly fluorinated carbon–fluorine bond, which is hard to break and requires a high amount of energy (536 kJ/mole). Resulting from their unique hydrophobic/oleophobic nature and their chemical and mechanical stability, they are highly resistant to thermal, chemical, and biological degradation. PFAS have been used extensively worldwide since the 1940s in various products such as non-stick household items, food-packaging, cosmetics, electronics, and firefighting foams. Exposure to PFAS may lead to health issues such as hormonal imbalances, a compromised immune system, cancer, fertility disorders, and adverse effects on fetal growth and learning ability in children. To date, very few novel membrane approaches have been reported effective in removing and destroying PFAS. Therefore, this article provides a critical review of PFAS treatment and removal approaches by membrane separation systems. We discuss recently reported novel and effective membrane techniques for PFAS separation and include a detailed discussion of parameters affecting PFAS membrane separation and destruction. Moreover, an estimation of cost analysis is also included for each treatment technology. Additionally, since the PFAS treatment technology is still growing, we have incorporated several future directions for efficient PFAS treatment.

Membrane-based technologies for per- and poly-fluoroalkyl substances (PFASs) removal from water: Removal mechanisms, applications, challenges and perspectives

Water purification from per- and poly-fluoroalkyl substances (PFASs), as a group of persistent and mobile fluoro-organic contaminants, is receiving increasing attention worldwide due to the ubiquitous presence of these highly toxic compounds. To reduce the risk of exposure of human life to PFASs and their dispersion in the environment, various techniques, primarily based on membrane technologies, have been rapidly developed. Here we critically review and analyze the current state-of-the-art of membrane-based techniques for PFASs removal, including direct membrane filtrations, adsorption-based membranes, and hybrid membrane processes. Membranes performance, treatment efficiencies, characteristic parameters and mechanisms for PFASs removal are discussed in detail. We highlight and discuss advantages and limitations, as well as challenges and prospects of individual membrane-based PFASs treatments, pointing towards the practical and sustainable application of these technologies.

Nanofiltration for drinking water treatment: a review

In recent decades, nanofiltration (NF) is considered as a promising separation technique to produce drinking water from different types of water source. In this paper, we comprehensively reviewed the progress of NF-based drinking water treatment, through summarizing the development of materials/fabrication and applications of NF membranes in various scenarios including surface water treatment, groundwater treatment, water reuse, brackish water treatment, and point of use applications. We not only summarized the removal of target major pollutants (e.g., hardness, pathogen, and natural organic matter), but also paid attention to the removal of micropollutants of major concern (e.g., disinfection byproducts, per- and polyfluoroalkyl substances, and arsenic). We highlighted that, for different applications, fit-for-purpose design is needed to improve the separation capability for target compounds of NF membranes in addition to their removal of salts. Outlook and perspectives on membrane fouling control, chlorine resistance, integrity, and selectivity are also discussed to provide potential insights for future development of high-efficiency NF membranes for stable and reliable drinking water treatment.

Advances and Applications of Hollow Fiber Nanofiltration Membranes: A Review

Hollow fiber nanofiltration (NF) membranes have gained increased attention in recent years, partly driven by the availability of alternatives to polyamide-based dense separation layers. Moreover, the global market for NF has been growing steadily in recent years and is expected to grow even faster. Compared to the traditional spiral-wound configuration, the hollow fiber geometry provides advantages such as low fouling tendencies and effective hydraulic cleaning possibilities. The alternatives to polyamide layers are typically chemically more stable and thus allow operation and cleaning at more extreme conditions. Therefore, these new NF membranes are of interest for use in a variety of applications. In this review, we provide an overview of the applications and emerging opportunities for these membranes. Next to municipal wastewater and drinking water processes, we have put special focus on industrial applications where hollow fiber NF membranes are employed under more strenuous conditions or used to recover specific resources or solutes.

Thermal insulation fibers with a Kevlar aerogel core and a porous Nomex shell

Kevlar aerogel fibers which inherit the aerogel's brilliant properties of low density, high porosity and large surface area are promising candidates for thermal insulation applications in textiles. To enhance the mechanical strength of Kevlar aerogel fibers, an extra Nomex shell was introduced by a simple coaxial-wet-spinning approach. The resultant coaxial fibers were observed to have a Kevlar aerogel core and a porous Nomex shell. Besides, there also formed an air gap between the core and the shell. This multi-layered coaxial structure with numerous pores inside contributes to the excellent thermal insulation performance of the fibers and their fabrics. The temperature differences between the hot plate and the outer surface of the fabrics were measured to be as high as 80 °C when exposed to a temperature of 300 °C. In addition, these fibers also performed well in thermal stability, and almost did not decompose before 380 °C. Not only that, the breaking strength of the Nomex shell can be up to twice that of the Kevlar core, resulting in a significant improvement in the fiber's mechanical strength. It can be envisaged that the developed coaxial fibers with excellent thermal insulation and endurance properties as well as improved mechanical strength may have broad prospects for thermal insulation at high temperatures.

Managing and treating per- and polyfluoroalkyl substances (PFAS) in membrane concentrates

Per- and polyfluoroalkyl substances (PFAS), which are present in many waters, have detrimental impacts on human health and the environment. Reverse osmosis (RO) and nanofiltration (NF) have shown excellent PFAS separation performance in water treatment; however, these membrane systems do not destroy PFAS but produce concentrated residual streams that need to be managed. Complete destruction of PFAS in RO and NF concentrate streams is ideal, but long-term sequestration strategies are also employed. Because no single technology is adequate for all situations, a range of processes are reviewed here that hold promise as components of treatment schemes for PFAS-laden membrane system concentrates. Attention is also given to relevant concentration processes because it is beneficial to reduce concentrate volume prior to PFAS destruction or sequestration. Given the costs and challenges of managing PFAS in membrane concentrates, it is critical to evaluate both established and emerging technologies in selecting processes for immediate use and continued research.

Influences of microwave irradiation on performances of membrane filtration and catalytic degradation of perfluorooctanoic acid (PFOA)

Perfluorooctanoic Acid (PFOA), one of the common per- and poly fluorinated alkylated substances (PFASs), is increasingly detected in the environment due to the diverse industrial applications and high resistance to degradation processes. This study evaluated degradation of PFOA in microwave-assistant catalytic membrane filtration, a process that integrates microwave catalytic reactions into a ceramic membrane filtration. First, water permeation of the pristine and catalyst-coated membranes were examined under the influence of microwave irradiation to analyse the impacts of the coating layer and water temperature increase on permeate flux, which were well interpreted by the Carman-Kozeny and Hagen-Posieulle (non-slipping and slit-like) models. Then, the PFOA removal was first assessed in a continuous filtration mode with and without microwave irradiation. Our results show that PFOA first adsorbed on membrane and catalyst materials, and then fully penetrated the membrane filter after reaching adsorption equilibrium. Under microwave irradiation (7.2 W·cm^-2), approximate 65.9% of PFOA (25 μg·L^-1) in the feed solution was degraded within a hydraulic time of 2 min (at the permeate flow rate of 43 LMH) due to the microwave-Fenton like reactions. In addition, low flow rates and moderate catalyst coating densities are critical for optimizing PFOA removal. Finally, potential degradation mechanisms of PFOA were proposed through the analysis of degradation by-products (e.g., PFPeA). The findings may provide new insight into the development of reactive membrane-enabled systems for destruction of refractory PFAS.

Water Treatment: Are Membranes the Panacea?

Alongside the rising global water demand, continued stress on current water supplies has sparked interest in using nontraditional source waters for energy, agriculture, industry, and domestic needs. Membrane technologies have emerged as one of the most promising approaches to achieve water security, but implementation of membrane processes for increasingly complex waters remains a challenge. The technical feasibility of membrane processes replacing conventional treatment of alternative water supplies (e.g., wastewater, seawater, and produced water) is considered in the context of typical and emerging water quality goals. This review considers the effectiveness of current technologies (both conventional and membrane based), as well as the potential for recent advancements in membrane research to achieve these water quality goals. We envision the future of water treatment to integrate advanced membranes (e.g., mixed-matrix membranes, block copolymers) into smart treatment trains that achieve several goals, including fit-for-purpose water generation, resource recovery, and energy conservation.

Surface molecular imprinting on carbon microspheres for fast and selective adsorption of perfluorooctane sulfonate

Perfluorooctane sulfonate (PFOS) is a persistent organic pollutant with high biological and chemical stability. It is important to develop fast and selective adsorption method for PFOS wastewater treatment. In this study, novel molecularly imprinted polymer (MIP) for PFOS adsorption was prepared. To obtain rapid adsorption kinetics, the MIP has been designed as the surface polymer using the carbon microsphere as carrier (MIP-CMSs). To ensure high adsorption selectivity to the template, two monomers with different functional structures, namely methacryloyloxyethyl trimethyl ammonium chloride (DMC) and 2-(trifluoromethyl)acrylic acid (TFMA), were employed as bi-functional monomers. The structure and morphology of MIP-CMSs were characterized using field emission scanning electron microscopy with the energy dispersive spectrometer, transmission electron microscopy, and Fourier transformation infrared spectroscopy. Based on the adsorption experiments, it was concluded that MIP-CMSs had specific binding property for PFOS on acidic condition. The adsorption equilibrium time was 1h, while the adsorption capacity was 75.99 mg g^-1 at pH 3. Coexistence with contaminants with different structures had little influence on the selectivity for PFOS. The spent MIP-CMSs could be regenerated by the methanol and acetic acid mixed solution. The electrostatic interaction and molecular size played important roles in recognizing the target compound in the adsorption process.

Recent developments in polyfluoroalkyl compounds research: a focus on human/environmental health impact, suggested substitutes and removal strategies

Between the late 1940s and early 1950s, humans manufactured polyfluoroalkyl compounds (PFCs) using electrochemical fluorination and telomerisation technologies, whereby hydrogen atoms are substituted by fluorine atoms, thus conferring unnatural and unique physicochemical properties to these compounds. Presently, there are wide ranges of PFCs, and owing to their bioaccumulative properties, they have been detected in various environmental matrices and in human sera. It has thus been suggested that they are hazardous. Hence, this review aims at highlighting the recent development in PFC research, with a particular focus on perfluorooctanoate (PFOA) and perfluorooctane sulfonate (PFOS), the most studied and predominantly found PFCs in various environmental matrices, although recent reports have included perfluorobutane sulfonate (PFBS), which was previously regarded as innocuously harmless, when compared to its counterparts, PFOA and PFOS. As such, proper investigations are thus required for a better understanding of short-chain PFC substitutes, which have been suggested as suitable replacements to long-chained PFCs, although these substitutes have also been suggested to pose various health risks comparable to those associated with long-chain PFCs. Similarly, several novel technologies, such as PFC reduction using zero-valent iron, including removal at point of use, adsorption and coagulation, have been proposed. However, regardless of how efficient removers some of these techniques have proven to be, short-chain PFCs remain a challenge to overcome for scientists, in this regard.

Efficient treatment of perfluorohexanoic acid by nanofiltration followed by electrochemical degradation of the NF concentrate

The present study was aimed at the development of a strategy for removing and degrading perfluorohexanoic acid (PFHxA) from industrial process waters at concentrations in the range 60-200 mg L^-1. The treatment train consisted of nanofiltration (NF) separation followed by electrochemical degradation of the NF concentrate. Using a laboratory-scale system and working in the total recirculation mode, the DowFilm NF270 membrane provided PFHxA rejections that varied in the range 96.6-99.4% as the operating pressure was increased from 2.5 to 20 bar. The NF operation in concentration mode enabled a volume reduction factor of 5 and increased the PFHxA concentration in the retentate to 870 mg L^-1. Results showed that the increase in PFHxA concentration and the presence of calcium sulfate salts did not induce irreversible membrane fouling. The NF retentate was treated in a commercial undivided electrochemical cell provided with two parallel flow-by compartments separated by bipolar boron doped diamond (BDD) electrode, BDD counter anode, and counter cathode. Current densities ranging from 20 to 100 A m^-2 were examined. The electrochemical degradation rate of PFHxA reached 98% and was accompanied by its efficient mineralization, as the reduction of total organic carbon was higher than 95%. Energy consumption, which was 15.2 kWh m^-3 of treated NF concentrate, was minimized by selecting operation at 50 A m^-2. While most of the previous research on the treatment of perfluoroalkyl substances (PFASs) focused on the removal of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS), these compounds have been phased out by chemical manufacturers. Our findings are relevant for the treatment of PFHxA, which appears to be one of the present alternatives to long-chain PFASs thanks to its lower bioaccumulative potential than PFOA and PFOS. However, PFHxA also behaves as a persistent pollutant. Moreover, our results highlight the potential of combining membrane separation and electrochemical oxidation for the efficient treatment of PFAS-impacted waters.

Study on the structural design and performance of novel braid-reinforced and thermostable poly(m-phenylene isophthalamide) hollow fiber membranes

Novel braid-reinforced (BR) PMIA hollow fiber membranes showing excellent mechanical property and thermal stability were fabricated.