Novel methodology for facile fabrication of nanofiltration membranes based on nucleophilic nature of polydopamine

Point-of-care dengue detection: polydopamine-modified electrode for rapid NS1 protein testing for clinical samples

Early diagnosis of dengue infection by detecting the dengue virus non-structural protein 1 (DENV-NS1) is important to the patients to initiate speedy treatment. Enzyme-linked immunosorbent assay (ELISA)-based NS1 detection and RT-PCR are time-consuming and too complex to be employed in remote areas of dengue-endemic countries. Meanwhile, those of NS1 rapid test by lateral flow assay suffer from low detection limit. Electrochemical-based biosensors using screen-printed gold electrodes (SPGEs) have become a reliable detection method to convey both ELISA's high sensitivity and rapid test portability. In this research, we developed an electrochemical biosensor for DENV-NS1 detection by employing polydopamine (PDA)-modified SPGE. The electrodeposition of PDA on the surface of SPGE serves as a bioconjugation avenue for anti-NS1 antibody through a simple and low-cost immobilization procedure. The biosensor performance was evaluated to detect DENV-NS1 protein in PBS and human serum through a differential pulse voltammetric (DPV) technique. The developed sensing platform displayed a low limit of detection (LOD) of 1.63 pg mL-1 and a wide linear range of 10 pg mL-1 to 1 ng mL-1 (R2 ∼ 0.969). The sensing platform also detected DEV-NS1 from four different serotypes in the clinical samples collected from dengue patients in India and Indonesia, with acceptable sensitivity, specificity, and accuracy values of 90.00%, 80.95%, and 87.65%, respectively. This result showcased the facile and versatile method of PDA coating onto the surface of screen-printed gold electrodes for a miniaturized point-of-care (PoC) detection device.

A Comprehensive Review of Performance of Polyacrylonitrile-Based Membranes for Forward Osmosis Water Separation and Purification Process

Polyacrylonitrile (PAN), with its unique chemical, electrical, mechanical, and thermal properties, has become a crucial acrylic polymer for the industry. This polymer has been widely used to fabricate ultrafiltration, nanofiltration, and reverse osmosis membranes for water treatment applications. However, it recently started to be used to fabricate thin-film composite (TFC) and fiber-based forward osmosis (FO) membranes at a lab scale. Phase inversion and electrospinning methods were the most utilized techniques to fabricate PAN-based FO membranes. The PAN substrate layer could function as a good support layer to create TFC and fiber membranes with excellent performance under FO process conditions by selecting the proper modification techniques. The various modification techniques used to enhance PAN-based FO performance include interfacial polymerization, layer-by-layer assembly, simple coating, and incorporating nanofillers. Thus, the fabrication and modification techniques of PAN-based porous FO membranes have been highlighted in this work. Also, the performance of these FO membranes was investigated. Finally, perspectives and potential directions for further study on PAN-based FO membranes are presented in light of the developments in this area. This review is expected to aid the scientific community in creating novel effective porous FO polymeric membranes based on PAN polymer for various water and wastewater treatment applications.

Fast preparation of a polydopamine/ceramic composite nanofiltration membrane with excellent permselectivity

Fabrication of a dense polymer/ceramic composite membrane with high permeability remains a great challenge. In this study, a highly selective polydopamine (PDA)/ceramic composite nanofiltration (NF) membrane was prepared by using an Al₂O₃ ceramic membrane with pore size of 0.1 μm as the support layer. In order to improve the membrane formation rate, KMnO₄ was introduced to oxidize the dopamine to improve the reactivity, and Na₂CO₃ was used to adjust the pH value of the dopamine solution. When the addition amount of KMnO₄ is 0.2 g L^-1 and that of Na₂CO₃ is 1 g L^-1, a functional layer can be formed within 10 min. PDA and polyethyleneimine (PEI) were added to the functional layer to adjust the selectivity of the composite membrane. The composite membrane showed a rejection of 99.7% towards Congo red dye with a high flux of 165 L (m² h bar)^-1 at ambient temperature. After 3 h treatment with Congo red, the fouling resistance of the membrane was improved compared with that of the ceramic based membrane. The surface morphology and composition of the composite membrane were also characterized with scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS), which confirmed the successful preparation of the PDA/ceramic composite membrane.

Progress for Co-Incorporation of Polydopamine and Nanoparticles for Improving Membranes Performance

Incorporating polydopamine has become a viable method for membrane modification due to its universality and versatility. Fillers in their different categories have been confirmed as effective elements to improve the properties of membranes such as hydrophilicity, permeability, mechanical strength, and fouling resistance. Thus, this paper mainly highlights the recent studies that have been carried out using polydopamine and nanomaterial fillers simultaneously in modifying the performance of different membranes such as ultrafiltration, microfiltration, nanofiltration, reverse osmosis, and forward osmosis membranes according to the various modification methods. Graphene oxide nanoparticles have recently attracted a lot of attention among different nanoparticles used with polydopamine, due to their impressive characteristics impacts on enhancing membrane hydrophilicity, mechanical strength, and fouling resistance. Thus, the incorporation techniques of graphene oxide nanoparticles and polydopamine for enhancing membranes have been highlighted in this work. Moreover, different studies carried out on using polydopamine as a nanofiller for optimizing membrane performance have been discussed. Finally, perspectives, and possible paths of further research on mussel-inspired polydopamine and nanoparticles co-incorporation are stated according to the progress made in this field. It is anticipated that this review would provide benefits for the scientific community in designing a new generation of polymeric membranes for the treatment of different feed water and wastewater based on adhesive mussel inspired polydopamine polymer and nanomaterials combinations.

Development of Novel Composite Membranes in Water/Wastewater Treatment

Composite membranes have attracted significant attention due to their flexibility in having more than one layer, with many materials being used to form the membrane [...]

A Facile Co-Deposition Approach to Construct Functionalized Graphene Quantum Dots Self-Cleaning Nanofiltration Membranes

In this study, a novel photocatalytic self-cleaning nanofiltration (NF) membrane was fabricated by constructing aspartic acid-functionalized graphene quantum dots (AGQDs) into the polydopamine/polyethyleneimine (PDA/PEI) selective layer via the co-deposition method. The chemical composition, microstructure, and hydrophilicity of the prepared membranes were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), attenuated total reflection (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), and water contact angle (WCA). Meanwhile, the effects of PEI molecular weight and AGQDs concentration on NF membrane structures and separation performance were systematically investigated. The photocatalytic self-cleaning performance of the PDA/PEI/AGQDs membrane was evaluated in terms of flux recovery rate. For constructing high-performance NF membranes, it is found that the optimal molecular weight of PEI is 10,000 Da, and the optimal concentration of AGQDs is 2000 ppm. The introduction of hydrophilic AGQDs formed a more hydrophilic and dense selective layer during the co-deposition process. Compared with the PDA/PEI membrane, the engineered PDA/PEI/AGQDs NF membrane has enhanced water flux (55.5 LMH·bar^-1) and higher rejection (99.7 ± 0.3% for MB). In addition, the PDA/PEI/AGQDs membrane exhibits better photocatalytic self-cleaning performance over the PDA/PEI membrane (83% vs. 69%). Therefore, this study provides a facile approach to construct a self-cleaning NF membrane.

Naturally Extracted Hydrophobic Solvent and Self-Assembly in Interfacial Polymerization

Pharmaceutical, chemical, and food industries are actively implementing membrane nanofiltration modules in their processes to separate valuable products and recover solvents. Interfacial polymerization (IP) is the most widely used method to produce thin-film composite membranes for nanofiltration and reverse osmosis processes. Although membrane processes are considered green and environmentally friendly, membrane fabrication has still to be further developed in such direction. For instance, the emission of volatile solvents during membrane production in the industry has to be carefully controlled for health reasons. Greener solvents are being proposed for phase-separation membrane manufacture. For the IP organic phase, the proposition of greener alternatives is in an early stage. In this work, we demonstrate the preparation of a high-performing composite membrane employing zero vapor pressure and naturally extracted oleic acid as the IP organic phase. Its long hydrophobic chain ensures intrinsic low volatility and acid monomer dissolution, while the polar head induces a unique self-assembly structure during the film formation. Membranes prepared by this technique were selective for small molecules with a molecular weight cutoff of 650 g mol^-1 and a high permeance of ∼57 L m^-2 h^-1 bar^-1.

Surface modification of nanofiltration membranes to improve the removal of organic micropollutants: Linking membrane characteristics to solute transmission

Surface modification of nanofiltration (NF) membranes has great potential to improve the removal of organic micropollutants (OMs) by NF membranes. This study used polydopamine (PDA) as a model coating to comprehensively link the changes in membrane properties with the changes in transmission of 34 OMs. The membrane characterization demonstrated that a thicker, denser, and more hydrophilic PDA coating can be achieved by increasing the PDA deposition time from 0.5 to 4 hours. Overall, the transmissions of target OMs were reduced by PDA-coated NF membranes compared to unmodified NF membranes. The neutral hydrophobic compounds showed lower transmissions for longer PDA coating (PDA4), while the neutral hydrophilic compounds tended to show lower transmissions for shorter PDA coating (PDA0.5). To explain this, competing effects provided by the PDA coatings are proposed including sealing defects, inducing cake-enhanced concentration polarization in the coating layer for neutral hydrophilic compounds, and weakened hydrophobic adsorption for neutral hydrophobic compounds. For charged compounds, PDA4 with the greatest negative charge among the PDA-coated membranes showed the lowest transmission. Depending on the molecular size and hydrophilicity of the compounds, the transmission of OMs by the PDA4 coating could be reduced by 70% with only a 26.4% decline in water permeance. The correlations and mechanistic insights provided by this work are highly useful for designing membranes with specific surface properties via surface modification to improve the removal of OMs without compromising water production.

Thin-film nanocomposite NF membrane with GO on macroporous hollow fiber ceramic substrate for efficient heavy metals removal

The ceramic membrane has been widely used in the wastewater treatment based on the chemical resistance and superior separation performance. A robust and defect-free thin-film nanocomposite (TFN) nanofiltration (NF) membrane on the macroporous hollow fiber ceramic (HFC) substrate was novelly developed for heavy metals removal. Before interfacial polymerization (IP), the aqueous solution of graphene oxide (GO) grafted with ethylenediamine (EDA) was deposited on the HFC substrate by vacuum filtration. Then, a thin polyamide (PA) film was fabricated by EDA and 1,3,5-trimesoyl chloride (TMC), followed by heat treatment. The effects of GO content and EDA concentration on the performance of the NF membrane have been systematically investigated. The results showed that when the GO content was 0.015 mg·mL^-1 and the EDA concentration was 0.75 wt.%, the as-prepared eGO₃/PA-HFC membrane had a rejection rate of 94.12% for MgCl₂ and a pure water flux of 18.03 L·m^-2·h^-1. Additionally, the removal ability of eGO₃/PA-HFC membranes for heavy metal ions was satisfactory (93.33%, 92.73%, 90.45% and 88.35% for Zn²⁺, Cu²⁺, Ni²⁺ and Pb²⁺, respectively). The study explored further that it was efficient and stable for heavy metal ions removal during 30 h in the simulated tap water and mining wastewater, which indicated that the eGO/PA-HFC membrane has great application potential in wastewater treatment.

Polydopamine Functionalized Graphene Oxide as Membrane Nanofiller: Spectral and Structural Studies

High-degree functionalization of graphene oxide (GO) nanoparticles (NPs) using polydopamine (PDA) was conducted to produce polydopamine functionalized graphene oxide nanoparticles (GO-PDA NPs). Aiming to explore their potential use as nanofiller in membrane separation processes, the spectral and structural properties of GO-PDA NPs were comprehensively analyzed. GO NPs were first prepared by the oxidation of graphite via a modified Hummers method. The obtained GO NPs were then functionalized with PDA using a GO:PDA ratio of 1:2 to obtain highly aminated GO NPs. The structural change was evaluated using XRD, FTIR-UATR, Raman spectroscopy, SEM and TEM. Several bands have emerged in the FTIR spectra of GO-PDA attributed to the amine groups of PDA confirming the high functionalization degree of GO NPs. Raman spectra and XRD patterns showed different crystalline structures and defects and higher interlayer spacing of GO-PDA. The change in elemental compositions was confirmed by XPS and CHNSO elemental analysis and showed an emerging N 1s core-level in the GO-PDA survey spectra corresponding to the amine groups of PDA. GO-PDA NPs showed better dispersibility in polar and nonpolar solvents expanding their potential utilization for different purposes. Furthermore, GO and GO-PDA-coated membranes were prepared via pressure-assisted self-assembly technique (PAS) using low concentrations of NPs (1 wt. %). Contact angle measurements showed excellent hydrophilic properties of GO-PDA with an average contact angle of (27.8°).

Poly(Homopiperazine-Amide) Thin-Film Composite Membrane for Nanofiltration of Heavy Metal Ions

The development of membrane-based technologies for the treatment of wastewater streams and resources containing heavy metal ions is in high demand. Among various technologies, nanofiltration (NF) membranes are attractive choices, and the continuous development of novel materials to improve the state-of-the-art NF membranes is highly desired. Here, we report on the synthesis of poly(homopiperazine-amide) thin-film composite (HTFC)-NF membranes, using homopiperazine (HP) as a monomer. The surface charge, hydrophilicity, morphology, cross-linking density, water permeation, solute rejection, and antifouling properties of the fabricated NF membranes were evaluated. The fabricated HTFC NF membranes demonstrated water permeability of 7.0 ± 0.3 L/(m2 h bar) and rejected Na2SO4, MgSO4, and NaCl with rejection values of 97.0 ± 0.6, 97.4 ± 0.5, and 23.3 ± 0.6%, respectively. The membranes exhibit high rejection values of 98.1 ± 0.3 and 96.3 ± 0.4% for Pb2+ and Cd2+ ions, respectively. The fouling experiment with humic acid followed by cross-flow washing of the membranes indicates that a flux recovery ratio (FRR) of 96.9 ± 0.4% can be obtained.

Surface modification of polypropylene membrane for the removal of iodine using polydopamine chemistry

The development of stable and effective iodine removal systems would be highly desirable in addressing environmental issues relevant to water contamination. In the present research, a novel iodine adsorbent was synthesized by self-polymerization of dopamine (PDA) onto inert polypropylene (PP) membrane. This PP/PDA membrane was thoroughly characterized and its susrface propeties was analyzed by various analytical techniques indcluding field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), Brunauer-Emmett-Teller (BET) and Barrett-Joyner-Halenda (BJH), contact angle, and surface free energy measurement. The PP/PDA membranes were subsequently used for batchwise removal of iodine at different temperatures (25-70 °C), pH (2-7), and surface areas (1-10 cm²) to understand the underlying adsorption phenomena and to estimate the membrane capacity for iodine uptake. The increase in temperature and pH both led to higher adsorption of iodine. The present approach showed a removal efficiency of over 75% for iodine using 10 cm² PP/PDA membrane (18.87 m² g^-1) within 2 h at moderate temperatures (∼50 °C) and pH > 4, about 15 fold compared to the PP control membrane. The adsorption kinetics and isotherms were well fitted to the pseudo-second-order kinetic and Langmuir isotherm models (R² > 0.99). This adsorbent can be recycled and reused at least six times with stable iodine adsorption. These findings were attributed to the homogenous monolayer adsorption of the iodide on the surface due to the presence of catechol and amine groups in the PP/PDA membrane. This study proposes an efficient adsorbent for iodine removal.

Elucidation of Titanium Dioxide Nucleation and Growth on a Polydopamine-Modified Nanoporous Polyvinylidene Fluoride Substrate via Low-Temperature Atomic Layer Deposition

Interfaces combining polydopamine (PDA) and nanoparticles have been widely utilized for fabricating hybrid colloidal particles, thin films, and membranes for applications spanning biosensing, drug delivery, heavy metal detection, antifouling membranes, and lithium ion batteries. However, fundamental understanding of the interaction between PDA and nanoparticles is still limited, especially the impact of PDA on nanoparticle nucleation and growth. In this work, PDA is used to generate functional bonding sites for depositing titanium dioxide (TiO₂) via atomic layer deposition (ALD) onto a nanoporous polymer substrate for a range of ALD cycles (<100). The resulting hybrid membranes are systematically characterized using water contact angle, scanning electron microscopy, atomic force microscopy, nitrogen adsorption and desorption, and X-ray photoelectron spectroscopy (XPS). An intriguing nonlinear relationship was observed between the number of ALD cycles and changes in surface properties (water contact angle and surface roughness). Together with XPS study, those changes in surface properties were exploited to probe the nanoparticle nucleation and growth process on complex PDA-coated porous polymer substrates. Molecular level understanding of inorganic and polymer material interfaces will shed light on fine-tuning nanoparticle-modified polymeric membrane materials.

A novel nanofiltration membrane inspired by an asymmetric porous membrane for selective fractionation of monovalent anions in electrodialysis

The present study describes the synthesis of new nanofiltration membranes inspired by asymmetric porous membranes used as monovalent anion selective membranes for electro-membrane separation.

Quantitative fabrication, performance optimization and comparison of PEG and zwitterionic polymer antifouling coatings

A versatile fabrication and performance optimization strategy of PEG and zwitterionic polymer coatings is developed on the sensor chip of surface plasma resonance (SPR) instrument. A random copolymer bearing phosphorylcholine zwitterion and active ester side chains (PMEN) and carboxylic PEG coatings with comparable thicknesses were deposited on SPR sensor chips via amidation coupling on the precoated polydopamine (PDA) intermediate layer. The PMEN coating showed much stronger resistance to bovine serum albumin (BSA) adsorption than PEG coating at very thin thickness (∼1nm). However, the BSA resistant efficacy of PEG coating could exceed that of PMEN due to stronger steric repelling effect when the thickness increased to 1.5∼3.3nm. Interestingly, both the PEG and PMEN thick coatings (≈3.6nm) showed ultralow fouling by BSA and bovine plasma fibrinogen (Fg). Moreover, changes in the PEG end group from -OH to -COOH, protein adsorption amount could increase by 10-fold. Importantly, the optimized PMEN and PEG-OH coatings were easily duplicated on other substrates due to universal adhesion of the PDA layer, showed excellent resistance to platelet, bacteria and proteins, and no significant difference in the antifouling performances was observed. These detailed results can explain the reported discrepancy in performances between PEG and zwitterionic polymer coatings by thickness. This facile and substrate-independent coating strategy may benefit the design and manufacture of advanced antifouling biomedical devices and long circulating nanocarriers.

STATEMENT OF SIGNIFICANCE

Prevention of biofouling is one of the biggest challenges for all biomedical applications. However, it is very difficult to fabricate a highly hydrophilic antifouling coating on inert materials or large devices. In this study, PEG and zwitterion polymers, the most widely investigated polymers with best antifouling performance, are conveniently immobilized on different kinds of substrates from their aqueous solutions by precoating a polydopamine intermediate layer as the universal adhesive and readily re-modifiable surface. Importantly, the coating fabrication and antifouling performance can be monitored and optimized quantitatively by a surface plasma resonance (SPR) system. More significantly, the SPR on-line optimized coatings were successfully duplicated off-line on other substrates, and supported by their excellent antifouling properties.

Surface modification of piperazine-based nanofiltration membranes with serinol for enhanced antifouling properties in polymer flooding produced water treatment

A facile membrane modification method with serinol to improve the membrane performance in the advanced treatment of polymer flooding produced water.

Bio-inspired Ni2+-polyphenol hydrophilic network to achieve unconventional high-flux nanofiltration membranes for environmental remediation

A Ni²⁺-polyphenol network was synthesized as a hydrophilic coating to achieve highly efficient nanofiltration membranes with an unconventional high flux for dye wastewater remediation.