Precisely-controlled modification of PVDF membranes with 3D TiO2/ZnO nanolayer: enhanced anti-fouling performance by changing hydrophilicity and photocatalysis under visible light irradiation

Membrane processes enhanced by various forms of physical energy: A systematic review on mechanisms, implementation, application and energy efficiency

Membrane technologies in water and wastewater treatment have been eagerly pursued over the past decades, yet membrane fouling remains the major bottleneck to overcome. Membrane fouling control methods which couple membrane processes with online in situ application of external physical energy input (EPEI) are getting closer and closer to reality, thanks to recent advances in novel materials and energy deliverance methods. In this review, we summarized recent studies on membrane fouling control techniques that depend on (i) electric field, (ii) acoustic field, (iii) magnetic field, and (iv) photo-irradiation (mostly ultraviolet or visible light). Mechanisms of each energy input were first reported, which defines the applicability of these methods to certain wastewater matrices. Then, means of implementation were discussed to evaluate the compatibility of these fouling control methods with established membrane techniques. After that, preferred applications of each energy input to different foulant types and membrane processes in the experiment reports were summarized, along with a discussion on the trends and knowledge gaps of such fouling control research. Next, specific energy consumption in membrane fouling control and flux enhancement was estimated and compared, based on the experimental results reported in the literature. Lastly, strength and weakness of these methods and future perspectives were presented as open questions.

Facile Preparation of PVDF/CoFe2O4-ZnO Hybrid Membranes for Water Depollution

In this investigation, CoFe2O4-PVDF and CoFe2O4-ZnO-PVDF hybrid membranes were prepared using a modified phase inversion method in which a magnetic field was applied during the casting process to ensure a uniform distribution of nanomaterials on the membrane surface. Thus, better absorption of light and increased participation of nanoparticles in the photodegradation process is ensured. The influence of nanomaterials on the crystalline structure, surface morphology, and hydrophilicity properties of the PVDF membrane was investigated. The obtained results indicated that the hybrid membrane exhibited significant differences in its intrinsic properties due to the nanomaterials addition. The hydrophilicity properties of the PVDF membrane were improved by the presence of nanoparticles. The photocatalytic decomposition of aqueous Rhodamine B solution in the presence of the prepared membrane and under visible light irradiation was tested. The hybrid membrane containing CoFe2O4-ZnO on its surface exhibited a high removal rate.

Ultrathin g-C3N4 composite Bi2WO6 embedded in PVDF UF membrane with enhanced permeability, anti-fouling performance and durability for efficient removal of atrazine

A novel Bi₂WO₆-g-C₃N₄/polyvinylidene fluoride (PVDF) composite ultrafiltration (UF) membrane (BWO-CN/PVDF) was prepared by microwave hydrothermal and immersion precipitation phase transformation method. The BWO-CN/PVDF-0.10 exhibited an outstanding photocatalytic removal rate of atrazine (ATZ) (97.65 %) under the simulated sunlight and enhanced permeate flux (1356.09 L·m^-2·h^-1). The multiple optical and electrochemical detection confirmed that combining ultrathin g-C₃N₄ and Bi₂WO₆ can increase carrier separation rate and prolong its lifetime. The quenching test revealed that h⁺ and ¹O₂ were the prominent reactive species. Additionally, after a 10-cycle photocatalytic process, the BWO-CN/PVDF membrane presented remarkable reusability and durability. And it showed excellent anti-fouling performance by filtering BSA, HA, SA, and Songhua River under simulated solar irradiation. The molecular dynamic (MD) simulation showed that the combination of g-C₃N₄ and Bi₂WO₆ can enhance the interaction between BWO-CN and PVDF. This work opens up a new idea for designing and constructing a highly efficient photocatalytic membrane for water treatment.

Research progress in external field intensification of forward osmosis process for water treatment: A critical review

Forward osmosis (FO) is an emerging permeation-driven membrane technology that manifests advantages of low energy consumption, low operating pressure, and uncomplicated engineering compared to conventional membrane processes. The key issues that need to be addressed in FO are membrane fouling, concentration polarization (CP) and reverse solute diffusion (RSD). They can lead to problems about loss of draw solutes and reduced membrane lifetime, which not only affect the water treatment effectiveness of FO membranes, but also increase the economic cost. Current research has focused on FO membrane preparation and modification strategies, as well as on the selection of draw solutions. Unfortunately, these intrinsic solutions had limited success in unraveling these phenomena. In this paper, we provide a brief review of the current state of research on existing external field-assisted FO systems (including electric-, pressure-, magnetic-, ultrasonic-, light- and flow-assisted FO system), analyze their mitigation mechanisms for the above key problems, and explore potential research directions to aid in the further development of FO systems. This review aims to reveal the feasibility of the development of external field-assisted FO technology to achieve a more economical and efficient FO treatment process.

High-performance photocatalytic membranes for water purification in relation to environmental and operational parameters

Growing technologies, increasing population and environmental pollution lead to severe contamination of water and require advanced water treatment technologies. These aspects lead to the need to purify water with advanced smart materials. This paper reviews the recent advances (during the last 5 years) in photocatalytic composite membranes used for water treatment. For this purpose, the authors have reviewed the main materials used in the development of (photocatalytic membranes) PMs, environmental and operational factors affecting the performance of photocatalytic membranes, and the latest developments and applications of PMs in water purifications. The composite photocatalytic membranes show good performance in the removal and degradation of pollutants from water.

Antifouling catalytic mixed-matrix membranes based on polyethersulfone and composition-optimized Zn-Cu-Fe-O CWAO catalyst under dark ambient conditions

Besides photocatalysts, novel catalytic wet-air oxidation (CWAO) catalysts capable of operating under mild conditions are a potential candidate to fabricate antifouling filtration membranes. This study optimized the CWAO catalyst consisting of three metal oxide components (ZnO, CuO, and Fe₃O₄) and used it to fabricate composite membranes with PES (polyethersulfone). The catalyst was characterized by methods such as FTIR, BET, XRD, UV-Vis DRS, XPS, ESR. The activity of the catalyst and the composite membranes was tested by the Acid Yellow 42 (AY42) degradation experiments in both cases with and without hydrogen peroxide at room conditions with air aeration. The pure water fluxes of composite membranes were also investigated based on a vacuum filtration system. The major degradation pathways of AY42 by the catalyst were proposed from the DFT (Density Functional Theory) and NBO (Natural Bond Orbital) calculations. The results showed that the optimal catalyst has molar ratios of Zn, Cu, and Fe metal ions of 0.05, 0.588, and 0.362, respectively, with AY42 decomposition efficiency of 88% in 3 h. The main factors affecting the catalytic efficiency of the CWAO catalyst determined from the trapping experiment were e^- and O₂. The results from different materials characterization methods have demonstrated the successful synthesis of the catalyst with a high surface area (103.5 m²/g) and small pore diameters (∼10 nm). The AY42 degradation of composite membranes was stable over five repeated cycles with over 70% efficiency. The pure water fluxes of composite membranes have also been significantly improved and are proportional to catalyst contents.

Catalytic and Physicochemical Evaluation of a TiO2/ZnO/Laccase Biocatalytic System: Application in the Decolorization of Azo and Anthraquinone Dyes

A TiO₂/ZnO oxide system was proposed as a support for the immobilization of laccase from Trametes versicolor (LTV). The obtained TiO₂/ZnO/LTV biocatalytic system was then applied in the decolorization/degradation of C.I. Reactive Black 5 and C.I. Acid Green 25 dyes. The efficiency of immobilization was evaluated based on catalytic properties (Bradford method, oxidation reaction of 2,2-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid)) and physicochemical (spectroscopic, porous, electrokinetic) analysis. The immobilization process was carried out with high performance (99.4%). Immobilized laccase retained about 40% of its activity in the whole analyzed temperature range and after 10 reaction cycles. Immobilization efficiency was also indirectly confirmed by the presence of characteristic functional groups (–C–H and –C–O), nitrogen and carbon on the TiO₂/ZnO/LTV biocatalytic surface, identified by spectroscopic analyses. The increase in the surface area to 126 m²/g, change of isoelectric point (2.0) and zeta potential ranges (from +12.0 to −20.0 mV) after the immobilization process were also observed. The results show that the designed biocatalytic system enables the removal of acid dyes (C.I. Reactive Black 5 and C.I. Acid Green 25) with high efficiency (99% and 70%, respectively). Mass spectroscopy analysis indicated possible degradation products formed by the cleavage of N=N and C–N bonds.

Photocatalytic self-cleaning properties of m-phenylene isophthalamide membranes enhanced by immobilization of GO-ZnO-Ag for dye wastewater disposal

Drawing self-cleaning technology into polymer membranes offers an extensive solution to overcome the membrane fouling obstacle. Herein, the GO-ZnO-Ag nano-hybrid particles with photocatalytic activity prepared via the microwave hydrothermal method were immobilized in poly(m-phenylene isophthalamide) (PMIA) membranes. Not only was the thorny issue in catalyst recovery avoided, but also the satisfactory photocatalytic self-cleaning performance of the polymer membrane was awarded. GO and noble metal silver nanoparticles (AgNPs) acted as a conductive electron transfer carrier and an electron host, respectively, which hindered the recombination rate of excited electrons and holes on ZnO under UV light. The UV-driven PMIA membrane photodegradation rates of MB and Cr(VI) were up to 97.2% and 94.3%, respectively, at 150 min on photodegradation kinetics. Also, MB was completely degraded at 180 min. For MB and Cr(VI) mix solutions, their degradation efficiencies were 78.1% and 71%, respectively. The BSA rejection rate of the modified polymer membrane was 93.8%, and the water flux was 408.8 (L·m−2·h−1). Permeability was maintained at a high level after repeated use. Therefore, the newly designed PMIA/GO-ZnO-Ag series membranes could expand the application of polymers in wastewater disposal industry.

Mussel-Inspired Immobilization of Photocatalysts with Synergistic Photocatalytic-Photothermal Performance for Water Remediation

The serious problem of pharmaceutical and personal care product pollution places great pressure on aquatic environments and human health. Herein, a novel coating photocatalyst was synthesized by adhering Ag-AgCl/WO₃/g-C₃N₄ (AWC) nanoparticles on a polydopamine (PDA)-modified melamine sponge (MS) through a facile layer-by-layer assembly method to degrade trimethoprim (TMP). The formed PDA coating was used for the anchoring of nanoparticles, photothermal conversion, and hydrophilic modification. TMP (99.9%; 4 mg/L) was removed in 90 min by the photocatalyst coating (AWC/PDA/MS) under visible light via a synergistic photocatalytic-photothermal performance route. The stability and reusability of the AWC/PDA/MS have been proved by cyclic experiments, in which the removal efficiency of TMP was still more than 90% after five consecutive cycles with a very little mass loss. Quantitative structure-activity relationship analysis revealed that the ecotoxicities of the generated intermediates were lower than those of TMP. Furthermore, the solution matrix effects on the photocatalytic removal efficiency were investigated, and the results revealed that the AWC/PDA/MS still maintained excellent photocatalytic degradation efficiency in several actual water and simulated water matrices. This work develops recyclable photocatalysts for the potential application in the field of water remediation.

Universal Intraductal Surface Antifouling Coating Based on an Amphiphilic Copolymer

Surface modification on the inner wall of medical or industrial polymeric catheters with a high length/diameter ratio is highly desired. Herein, a universal and facile method based on an amphiphilic copolymer was developed to immobilize an intraductal surface antifouling coating for a variety of polymeric catheters. A fouling-repelled thin layer was formed by swelling-driven adsorption via directly perfusing an amphiphilic copolymer [polyvinylpyrrolidone-polydimethylsiloxane-polyvinylpyrrolidone (PVP-PDMS-PVP)] solution into catheters. In this copolymer, hydrophobic PDMS was embedded into a shrinking cross-linked network of catheters; also, PVP segments migrated to the surface under driving water to form a hydrophilic antifouling coating. Moreover, because of the coordination between I₂ and pyrrolidone of PVP, the copolymer-modified intraductal surface was then infused with aqueous I₂ to form the PVP-I₂ complex, endowing this coating with bactericidal activity. Notably, diverse catheters with arbitrary shapes (circular, rectangular, triangular, and hexagonal) and different components (silicone, polyurethane, and polyethylene) were also verified to work using this interfacial interpenetration strategy. The findings in this work provide a new avenue toward facile and universal fabrication of intraductal surface antifouling catheters, creating a superior option for decreasing the consumable costs in industrial production and alleviating the pain of replacing catheters for patients.

Ongoing progress on novel nanocomposite membranes for the separation of heavy metals from contaminated water

Membranes, as the primary separation element of membrane-based processes, have greatly attracted the attention of researchers in several water treatment applications, including wastewater treatment, water purification, water disinfection, toxic and non-toxic chemical molecules, heavy metals, among others. Today, the removal of heavy metals from water has become challenging, in which chemical engineers are approaching new materials in membrane technologies. Therefore, the current review elucidates the progress of using different concepts of membranes and potential novel materials for such separations, identifying that polymeric membranes can exhibit a removal efficiency from 77 up to 99%; while novel nanocomposite membranes are able to offer complete removal of heavy metals (up to 100%), together with unprecedented permeation rates (from 80 up to 1, 300 L m^-2 h^-1). Thereby, the review also addresses the highlighted literature survey of using polymeric and nanocomposite membranes for heavy metal removal, highlighting the relevant insights and denoted metal uptake mechanisms. Moreover, it gives up-to-date information related to those novel nanocomposite materials and their contribution to heavy metals separation. Finally, the concluding remarks, future perspectives, and strategies for new researchers in the field are given according to the recent findings of this comprehensive review.

Integrated photocatalysis-adsorption-membrane separation in rotating reactor for synergistic removal of RhB

A synergistic system of integrated photocatalysis-adsorption-membrane separation in a rotating reactor was designed. The composite membrane was prepared via filtration process under vacuum, and it was composed of graphene oxide (GO) acted as the separation membrane, activated carbon (AC) as the adsorbent and Ag@BiOBr as the photocatalyst, respectively. In this Ag@BiOBr/AC/GO membrane system, rotation of the membrane could avoid the light-shielding effect from organic color pollutants to achieve the complete removal of pollutants. More importantly, the synergistic effect among photocatalysis, adsorption and membrane separation in rotating reactor was significant for the efficient removal of rhodamine B (RhB). In the Ag@BiOBr/AC/GO composite membrane, GO membrane layer could reject the organic molecular by the assistance of AC layer with efficient adsorption capacity, and Ag@BiOBr at outer layer could photodegrade the organics under visible light irradiation. The photocatalysis process could solve the problem of membrane fouling and adsorption could assist GO membrane for stopping the permeation of pollutants. Meanwhile, GO membrane was not only beneficial for catalyst recovery, but also could concentrate the pollutants via the membrane separation to accelerate the photocatalytic degradation. At the same time, both the photocatalysis degradation and membrane separation could promote the adsorption ability of AC. This synergistic system showed the significant potential for the practical application in the future.

Reversible filtration redox of methylene blue in dimethylsulfoxide by manganese oxide loaded carbonaceous nanofibrous membrane through Fenton-like oxidation

The reversible redox of methylene blue in organic solvents was highly attractive, yet was rarely reported. In this study, we realized the continuous filtration redox of methylene blue (MB) in dimethylsulfoxide (DMSO) through Fenton-like oxidization by using MnO₂ loaded carbonaceous nanofibrous membrane (cPAN-MnO₂). The carbonaceous nanofibrous membrane (cPAN) was fabricated through electrospun of polyacrylonitrile and subsequent carbonization. The obtained cPAN nanofibrous membrane showed excellent stability in polar DMSO. MnO₂ can be readily coated on cPAN nanofibers through an in situ redox reaction between cPAN and potassium permanganate. The fabricated cPAN-MnO₂ membrane exhibited instantaneous reduction property towards MB in DMSO during a gravity-driven continuous filtration process. Interestingly, MB reduction was initiated by a typical Fenton-like oxidization, where hydroxyl radicals were firstly generated from hydrogen peroxide catalyzed by MnO₂ in DMSO. Then hydroxyl radicals attacked DMSO to further produce methyl radicals, which resulted in the reduction of MB. In addition, MB reduction process in DMSO was reversible. Our study provides a novel strategy for continuous redox of MB in polar organic solvent and might give new ideas for MB applications.

Drawing on Membrane Photocatalysis for Fouling Mitigation

Photocatalysis is an effective and environmentally friendly approach for degrading organic pollutants, particularly in scenarios where sunlight can be utilized as the energy source. Opportunities are emerging to apply materials and methods from photocatalytic pollutant degradation to address the challenge of fouling. Membrane fouling, attributed to organic foulants, is a prevalent problem for all membrane-based technologies and represents a major deleterious impact on membrane performance. Integration of tactics developed in photocatalysis more broadly to membranes reveals new strategies for membrane fouling control-an approach taken by an increasing number of researchers. This review summarizes key developments in photocatalytic materials and methods in water treatment and presents recent progress in the development of processes for photocatalytic alleviation of membrane fouling, including photocatalyst design and modification strategies aimed at enhancing photocatalytic efficiency, as well as different configurations of photocatalysis-membrane systems (PMS). Perspectives on future research and development opportunities for photocatalytic membrane fouling control are also provided.

A novel PVDF-TiO2@g-C3N4 composite electrospun fiber for efficient photocatalytic degradation of tetracycline under visible light irradiation

A novel composite electrospun fiber with high photocatalytic efficiency, good stability, strong hydrophobicity, good pollution resistance, and easy separation and recovery was synthesized. The TiO₂@g-C₃N₄ (TCN) with special core-shell structure (5-10 nm shell) facilitated the separation of photogenerated electron-holes and had high photocatalytic performance. The poly (vinylidene fluoride) (PVDF) electrospun fiber immobilized with TCN was successfully fabricated (PVDF-TCN) with uniform distribution and size of nanofibers by using electrospinning, which was used for degrading tetracycline under visible-light irradiation (> 400 nm). A special rougher surface of electrospun fiber obtained by washing of sacrificial PVP increased the specific surface area, which became more conducive to the adhesion of the catalyst. The water contact angle and FTIR results demonstrated that the electrospun fiber became extremely hydrophilic after adding TCN catalyst, which could effectively mitigate the fiber pollution. The PVDF-TCN-0.2g electrospun fiber exhibited excellent photocatalytic performance and the degradation efficiency of tetracycline was up to 97% in 300 min under visible-light irradiation. The mechanism of PVDF-TCN electrospun fiber degradation of tetracycline in the photocatalytic process was also proposed. In addition, the PVDF-TCN-0.2g exhibited a stable activity after 4 cycles experiments since the degradation efficiency remained about 90%. Therefore, we believed this study provided a new strategy in catalyst immobilization and wastewater treatment.

Aquatic environment remediation by atomic layer deposition-based multi-functional materials: A review

Water pollution still poses significant threats to the ecosystem and human health today. The adsorption, advanced oxidation and membranes filtration have been extensively investigated and utilized for aquatic contaminants remediation, and their efficiency is closely correlated with the advanced materials design and fabrication (e.g. adsorbents, catalysts and membranes). Thanks to uniform deposition, three-dimensional conformity and process controllability, the atomic layer deposition (ALD) has emerged as a promising strategy for fabrication of these multifunctional materials, arising their successful application in aquatic contaminants remediation. Therefore, a timely review on ALD-based water treatment materials is highly important to summarize the current opportunity and elucidate unaddressed problems in this field. Herein, in this review, the advantages of ALD process, the superiority of ALD-based materials and the corresponding decontamination performance were analyzed comprehensively, highlighting key advantages offered by this technology.

Immobilization techniques of a photocatalyst into and onto a polymer membrane for photocatalytic activity

This article reviews the various techniques of immobilizing a photocatalyst into and onto the polymer membrane for pollutant removal and as a problem solver in handling suspended photocatalyst issues from the previous literature. A particular focus is given to the preparation of mixed matrix membranes and deposition techniques for photocatalytic degradation in applications for wastewater treatment. Advantages and disadvantages in this application are evaluated. Various operating conditions during the process are presented. About 90 recently published studies (2008–2020) are reviewed. From the literature, it was found that TiO₂ is the most favoured photocatalyst that is frequently used in photocatalytic water treatment. Dry–wet co-spinning and sputtering techniques emerged as the promising technique for immobilizing a uniformly distributed photocatalyst within the polymeric membrane, and exhibited excellence pollutant removal. In general, the technical applicability is the key factor in selecting the best photocatalyst immobilizing technique for water treatment. Finally, the scope of various techniques that have been reviewed may provide potential for future photocatalytic study.

This article reviews the various techniques of immobilizing a photocatalyst into and onto the polymer membrane for pollutant removal and as a problem solver in handling suspended photocatalyst issues from the previous literature.

Novel strategy for membrane biofouling control in MBR with CdS/MIL-101 modified PVDF membrane by in situ visible light irradiation

Novel control strategies for membrane biofouling with eco-friendly photocatalytic technology are critically needed in practical operation of membrane bioreactors (MBRs). In this study, a metal-organic frameworks (MOF) based photocatalytic membrane was firstly applied in an anammox MBR for a long-term biofouling control, where bacteria were inactivated and foulants were degraded simultaneously, with environmentally friendly and renewable visible light energy. By physicochemical characterization, the synthesized photocatalyst of CdS/MIL-101 showed superior visible-light photocatalytic ability, and the 1 wt% CdS/MIL-101 modified membrane C2 showed enhanced hydrophilicity and water permeability compared with the pristine membrane C0. In the long-term operation of anammox MBRs under waterproof lights irradiation, the filtration cycles of C2 (25-26 d) were obviously extended compared with C0 (10-14 d), while their average total nitrogen removal efficiencies were comparable up to 84%, indicating an excellent biofouling alleviation effect by using C2 with a satisfactory nitrogen removal performance maintained. By analysis of the biofilm on the fouled membranes, the organic foulants (especially extracellular polymeric substances) were degraded, and the live bacteria were inactivated effectively by the photocatalytic reactions of CdS/MIL-101 on C2. In the antimicrobial tests against model bacteria, C2 exhibited remarkable antimicrobial effect against both Gram-negative and Gram-positive bacteria with visible light irradiation by destruction of cell integrity with the inhibition rate of 92% for Escherichia coli and 95% for Staphylococcus aureus, respectively. In the model foulants (bovine serum albumin, sodium alginate, and humic acid) filtration tests, C2 showed higher antifouling capabilities, lower flux declining rates, and higher foulants rejection rates under visible light irradiation compared with C0. The reactive species of ·OH, e^- and h⁺ generated on C2 were verified to play the predominant role in the anti-biofouling processes by simultaneous bacteria inactivation and foulants degradation. The findings offer a novel insight into the biofouling controlling in MBRs by simultaneous bacteria inactivation and foulants degradation with an eco-friendly method.

Efficient removal of mercury ions with MoS2-nanosheet-decorated PVDF composite adsorption membrane

The exploitation of a new adsorbent with a high adsorption performance and recyclability is of great practical significance for the treatment of wastewater containing mercury ions. In this study, a novel membrane adsorbent was fabricated by blending MoS₂ nanosheets into a PVDF polymer matrix (P-PVDF/MoS₂) followed by non-solvent-induced phase conversion. This material was able to bind mercury ions and was not affected by the solution ionic strength, co-existing anions, or interfering heavy metal ions. The optimal pH range for mercury ion elimination was 4.5-6.0, and P-PVDF/MoS₂ exhibited a maximum adsorption capacity of 578 mg g^-1. The pseudo-second-order adsorption kinetics and Langmuir isotherm models best described the adsorption process. The adsorption mechanism was mainly monolayer chemisorption, for which the S groups were the major active sites. Furthermore, the membrane could be removed from the aqueous solution easily using tweezers, and the removal efficiency of mercury ions remained over 90% after ten cycles. This study suggests that the inexpensive and recyclable P-PVDF/MoS₂ membranes can be used for the efficient removal of heavy metal ions from wastewater at a large scale.

Photocatalytic study of nanocomposite membrane modified by CeF3 catalyst for pharmaceutical wastewater treatment

Cerium fluoride (CeF₃) nanoparticles (NPs) were synthesized and applied in polysulfone (PS) membrane fabricated by phase inversion method. The produced nanocomposite membranes (PS/CeF₃) with different contents of CeF3 NPS (0.25%, 0.5%, 0.75% and 1% w/w) were used to treat pharmaceutical wastewaters. The membranes were characterized by FESEM, EDX, XRD, FTIR, porosity, and water contact angle analyses. Evaluation of the characteristics and performance of the nanocomposite membranes confirmed that utilizing photocatalytic CeF₃ NPs in membrane structure could effectively decompose organic contaminants in pharmaceutical wastewaters. It also improves the hydrophilicity and antifouling ability of membrane during filtration especially, in the presence of UV irradiation. The permeate flux of the PS membrane increased from 35.1 to 63.77 l/m²h by embedding 0.75% of CeF₃ NPs in membrane structure due to the porosity enhancement from 71.36-78.42% and the decrease in contact angle from 62.9º to 53.73º. Moreover, the flux decline of PS/CeF₃-0.75% membrane under UV irradiation was from 63.6 to 46.1 l/m²h that considerably lower than that of the neat PS membrane (from 34.7 to 4.9). On the other hand, the degradation efficiency of PS/CeF₃-0.75% membrane was more than 97%, and COD removed was more than 65% while they were 75% and 31%, respectively for the nascent PS membrane. Therefore, applying the appropriate amount of CeF₃ NPs in PS membranes not only greatly increased the permeate flux but also significantly enhanced the degradation efficiency and COD removal. This indicates that nanocomposite membranes can be confidently applied for pharmaceutical wastewater treatment UV irradiation.

Performance Evaluation and Kinetic Analysis of Photocatalytic Membrane Reactor in Wastewater Treatment

The objectives of the current study are to assess and compare the performance of a developed photocatalytic membrane reactor (PMR) in treating industrial waste (e.g., organic dye waste) against membrane distillation. The current PMR is composed of a feed tank, which is a continuous stirred photocatalytic reactor containing slurry Titanium dioxide (TiO₂) particles that are activated by using ultraviolet lamp irradiation at a wavelength of 365 nm, and a poly-vinylidene flouride (PVDF) membrane cell. The experimental setup was designed in a flexible way to enable both separate and integrated investigations of the photocatalytic reactor and the membrane, separately and simultaneously. The experimental work was divided into two phases. Firstly, the PVDF membrane was fabricated and characterized to examine its morphology, surface charge, and hydrophobicity by using a scanning electron microscope, surface zeta potential, and contact angle tests, respectively. Secondly, the effects of using different concentrations of the TiO₂ photocatalyst and feed (e.g., dye concentration) were examined. It is found that the PMR can achieve almost 100% dye removal and pure permeate is obtained at certain conditions. Additionally, a kinetic analysis was performed and revealed that the photocatalytic degradation of dye follows a pseudo-first-order reaction.

Functional catalytic membrane development: A review of catalyst coating techniques

Catalytic membranes combine catalytic activity with conventional filtration membranes, thus enabling diverse attractive benefits into the conventional membrane filtration processes, such as easy catalyst reuse, antifouling, anti-microbial, and enhancing process efficiency. Up to date, tremendous progresses have been made on functional catalytic membrane preparation and applications, which significantly advances the competitiveness of membrane technologies in process industries. The present article provides a critical and holistic overview of the current state of knowledge on existing catalyst coating techniques for functional catalytic membrane development. Based on coating mechanisms, the techniques are generally categorized into physical and chemical surface coating routes. For each technique, we first introduce fundamental principle, followed by a critical discussion of their applications with representative case studies. Advantages and drawbacks are also emphasized for different surface coating technologies. Finally, future perspectives are highlighted to provide deep insights into their future developments.

Araneose Ti3+ self-doping TiO2/SiO2 nanowires membrane for removal of aqueous MB under visible light irradiation

Araneose Ti³⁺ self-doped TiO₂/SiO₂ nanowires (RTiO₂/SiO₂) were prepared and anchored onto a polyethersulfone (PES) membrane. Careful characterizations and measurements indicated a covalent grafting of SiO₂ onto reduced TiO₂ (RTiO₂) through Ti-O-Si linkages, acquiring uniformed RTiO₂/SiO₂ nanowires of almost complete anatase and benign hydrophilicity. The RTiO₂/SiO₂-based PES membrane showed a significantly enhanced visible light-driven degradation rate of methylene blue (MB) (90.7%), compared with that on bare PES (11.1%) and PES-RTiO₂ (59.6%) membranes. The residual MB in filtered water was less than 5% after reusing three times. The normalized permeate flux of the modified membrane was 0.83, and the transmembrane pressure only increased by 0.4 MPa under irradiation of visible light. The improved performance of the PES-RTiO₂/SiO₂ was attributed to efficient intercept of MB molecular, light harvesting of visible light, and separation of charge carriers on araneose RTiO₂/SiO₂ nanowires.

In-Situ Surface Modification of Terpinen-4-ol Plasma Polymers for Increased Antibacterial Activity

Surface modification of thin films is often performed to enhance their properties. In this work, in situ modification of Terpinen-4-ol (T4) plasma polymer is carried out via simultaneous surface functionalization and nanoparticle immobilization. Terpinen-4-ol plasma polymers surface were decorated with a layer of ZnO nanoparticles in an oxygen plasma environment immediately after polymer deposition. A combination of hydrophilic modification and ZnO nanoparticle functionalization of the T4 polymer surface led to an enhancement in antibacterial properties by factor of 3 (from 0.75 to 0.25 CFU.mm-2). In addition, ZnO nanoparticle-modified coatings demonstrated improved UV absorbing characteristics in the region of 300-400 nm by 60% relative to unmodified coatings. The ZnO modified coatings were transparent in the visible region of 400-700 nm. The finding points towards the potential use of ZnO nanoparticle-modified T4 plasma polymers as optically transparent UV absorbing coatings.

Fabrication of hierarchical layer-by-layer membrane as the photocatalytic degradation of foulants and effective mitigation of membrane fouling for wastewater treatment

A polyvinylidene fluoride plate sheet membrane coated 3D TiO₂/poly (sodium styrenesulfonate) (PSS) photocatalyst layers were fabricated via dip-coating layer-by-layer (LbL) assembly. Cationic TiO₂ and anionic PSS were alternately stacked on the support membrane via electrostatic interactions. The obtained modified membrane with (TiO₂/PSS)₇ exhibited optimal versatility under ultraviolet light irradiation in both dead-end and membrane reactor, which showed superior Lanasol Blue 3R (LB) removal rate to membrane filtration and biodegradation. The modified membranes (MM) exhibited good performance in terms of photocatalytic activity of foulant degradation and mitigation of membrane fouling in a membrane reactor. The obtained MM with (TiO₂/PSS)₇ exhibited optimal versatility under ultraviolet light irradiation in both dead-end and membrane reactors and superior Lanasol Blue 3R removal rate in membrane filtration and biodegradation. The MM (TiO₂/PSS)₇ possessed excellent antifouling properties by using bovine serum albumin (BSA), as evidenced by the extended Derjaguin-Landau-Verwey-Overbeek theory. Additionally, the TiO₂/PSS membrane showed good self-cleaning ability, and the foulants on the membrane surface could be degraded using ultraviolet light irradiation.

Highly Efficient Purification of Multicomponent Wastewater by Electrospinning Kidney-Bean-Skin-like Porous H-PPAN/rGO-g-PAO@Ag+/Ag Composite Nanofibrous Membranes

Due to the complexity of harmful wastewater components, environmental and multifunctional materials are required for sewage purification. In this paper, a novel kidney-bean-skin-like hydrophilic porous polyacrylonitrile/reduced graphene oxide-g-poly(amidoxime)-loaded Ag⁺ (H-PPAN/rGO-g-PAO@Ag⁺/Ag) composite nanofiber membrane was fabricated by combining electrospinning and hydrolysis methods. The spinning solution was pumped at a rate of 0.4 mL/h with the voltage set at a constant value of 23 kV. Then, some of the -CN groups switched to hydrophilic -COOH groups via a hydrolysis method, which acts as a linker of GO-g-PAN, Ag⁺, and the polyacrylonitrile (PAN) matrix. A further step of chelation and thermal treatment were used for generating Schottky junctions between rGO-g-PAO@Ag⁺ and Ag. After five-cycle tests, it exhibited outstanding mechanical properties ensuring the filtration and purification performance of the H-PPAN/rGO-g-PAO@Ag⁺/Ag composite nanofiber membrane (i.e., the tensile strength was still 7.21 MPa, and the elongation was 61.53%) for simulated wastewater. The methods of thermal treatment and high-pressure Hg lamp irradiation promoted the reduction of GO to rGO and Ag⁺ to Ag particles, which endows the final product H-PPAN/rGO-g-PAO@Ag⁺/Ag with excellent photocatalytic and bactericidal properties. Its catalytic efficiency for dyes benzoic acid (BA), Rhodamine B (RhB), methylene blue (MB), and methyl orange (MO) was up to 99.8, 98, 95, and 91%. The antibacterial rate was 100% against Escherichia coli and 99% against Staphylococcus aureus. More importantly, the photocatalytic and antibacterial PAN-based nanofiber membrane can be simply scaled up, which provides the membrane with great potential in highly efficient wastewater treatment and augmenting water supply.

Evaluation of self-cleaning performance of the modified g-C3N4 and GO based PVDF membrane toward oil-in-water separation under visible-light

Photocatalytic membranes (PMs), coupling of membrane filtration and photocatalysis, have exhibited the potential for application in the wastewater treatment. In this study, we firstly adopted the supramolecular aggregates of melamine (M), cyanuric acid (C), and urea (U) in specific dimethyl sulfoxide (DMSO) as precursors to prepare carbon nitride MCU-C₃N₄ with high photocatalytic performance, and a kind of novel-designed photocatalytic membrane was prepared via filtrating the mixture of graphene oxide (GO) nanosheets and MCU-C₃N₄ on PVDF membrane supports, and then crosslinked using glutaraldehyde (GA) to construct a steady coating on the GO/MCU-C₃N₄/PVDF membrane. GO/MCU-C₃N₄/PVDF composite membrane exhibited higher permeation flux than that of GO/PVDF membrane and exhibited excellent separation performance for oil-in-water emulsion. A visible light-driven self-cleaning four-stage filtration by a self-built dead-end filtration system was carried out to evaluate membrane antifouling property, and GO/MCU-C₃N₄/PVDF membrane (M2) possessed higher flux recovery ratio (FRR) (∼92.36%) and lower irreversible fouling resistance (R_ir) ratio (∼8%) under 30min visible-light irradiation, maintaining relatively higher FRR (>72%) during 4 cycling of four-stage filtrating experiments. GO/MCU-C₃N₄/PVDF PMs are equipped with high permeation flux, separation performance, anti-fouling property and stability, indicating potential application in water treatment.