New promising polymer for organic solvent nanofiltration: Oxidized poly (arylene sulfide sulfone)

Research progress on the surface modification of carbon fiber

Carbon fiber (CF) has high strength, high modulus, and excellent high-temperature resistance and chemical stability; therefore, it is used in diverse fields. However, due to the lack of active functional groups on the surface of CF and surface defects generated during the preparation of CF, the wettability of the fiber surface is poor, which seriously affects the interface performance between the fiber and a resin matrix. In recent years, extensive research has been conducted on the surface modification of CF. In this review, studies on the surface modification of CF are summarized, including the various methods utilized, such as dry modification, wet modification, and nanomodification, as well as their current application status. As interest in this material increases, high-performance CFs will likely play an important role in many fields in the future.

Ni-Catalyzed Hydrosulfonylation of Alkenes with Aromatic Iodides and K2S2O5

Hydrosulfonylation of alkenes with readily available aromatic iodides via a SO2-insetion strategy is presented. The combination of non-noble Ni catalysis with (iPr)3SiH as the final reductant enables the efficient formation of aryl and heteroaryl sulfinate intermediates, which undergo Michael-type additions to electron-deficient alkenes for initiating the hydrosulfonylation process. Moreover, the superiority of this protocol is demonstrated by broad substrate scope and good functional group compatibility.

New Strategy for Improvement of Interfacial Interactions between Poly(arylene sulfide sulfone) and Carbon Fiber by Grafting Polymeric Chains via Thiol-Ene Click Chemistry

A simple and efficient strategy for enhancing the interfacial interaction in carbon fiber-reinforced poly(arylene sulfide sulfone) (CF/PASS) composites by grafting polymeric chains via thiol-ene click chemistry is reported here. Simultaneously, three thiol compounds and carbon nanotubes were grafted on CFs to explore the reaction between the CF and thiol groups. X-ray photoelectron spectroscopy, Raman spectroscopy, and normalized temperature-dependent IR spectroscopy results confirm the successful grafting of three thiol compounds, carbon nanotubes, and polymer chains. Similarly, obvious changes on the CF surface can be seen before and after modification via scanning electron microscopy, such as grafted nanotubes and polymeric resin, and the increase in the modulus gradient and interfacial thickness of CF/PASS can be clearly seen via atomic force microscopy. All the results of micro and macro tests on mechanical properties indicate that connecting low molecular weight thiol-terminated PASS (HS-LPASS) onto CFs enhances the interfacial property and mechanical performance of CF/PASS to a greater extent. The interfacial shear strength, interlaminar shear strength, and tensile strength of CF@HS-LPASS-reinforced PASS (CF@HS-LPASS/PASS) increase significantly by 38.5, 43.6, and 24.4%, respectively. All the results demonstrate that thiol-ene click reactions can be used for CF modification; furthermore, in the presence of external stress, the grafted polymeric interphase can act as a "bridge layer" to improve the stress transfer efficiency.

Improve the Interfacial Properties between Poly(arylene sulfide sulfone) and Carbon Fiber by Double Polymeric Grafted Layers Designed on a Carbon Fiber Surface

Double polymeric grafted layer is constructed by two steps of chemical reaction, in which two polymers had been used, respectively polydopamine (PDA) film and modified PASS (NH₂-PASS) resin containing amine group, as the interphase in carbon fiber reinforced poly(arylene sulfide sulfone) (PASS) composite (CF/PASS) to work on enhancing the interfacial property. All the test results of chemical components and chemical structures on the carbon fiber surface show that the double polymeric grafted layer was constructed successfully with PDA and NH₂-PASS chains. And obvious characteristics of thin PDA film and a polymer layer can be clearly seen in the morphology of modified carbon fiber. In addition to this, the obvious interphase and change in the thickness of interphase have been observed in the modulus distribution images of CF/PASS. The final superb performance is achieved by PASS composites with a double polymeric grafted layer, 27.2% and 198.6% superior to the original PASS composite for IFSS and ILSS, respectively. Moreover, the result also indicates that constructing a double polymeric grafted layer on a carbon fiber surface is a promising technique to modify carbon fiber for processing high-performance advanced thermoplastic composites and is more environmental friendly as well as convenient.

Atom-Economical, Catalyst-Free Hydrosulfonation of Densely Functionalized Alkenes: Access to Oxindole Containing Sulfones

An atom-economical hydrosulfonation of densely functionalized alkenes under catalyst-free conditions is described. Alkenes possessing hydroxy-oxindole moiety underwent hydrosulfonation on treatment with arylsulfinic acids in green media to afford the resulting...

High-performance filter membrane composed of oxidized Poly (arylene sulfide sulfone) nanofibers for the high-efficiency air filtration

In this study, a novel, oxidized poly (arylene sulfide sulfone) (O-PASS) nanofibrous membrane filter was successfully fabricated for the effective removal of particulate matter. PASS was electrospun into a nanofibrous membrane with an average nanofiber diameter of 0.31 µm and basis weight of 3 g/m². These specifications were chosen as they showed high particulate matter removal efficiency (99.98%), low pressure drop (68 Pa), and high quality factor Q_F (0.125 Pa^-1). In addition, the filtration mechanism of the PASS nanofibrous membrane was intuitively revealed by simulating the intercepted particular distributions and motion paths of particles. After a simple oxidation treatment, the O-PASS nanofibrous membrane was successfully built up. The microstructure and morphology showed little change compared with the PASS nanofiber, but the oxidation treatment significantly improved the mechanical properties of the membrane from 1.51 MPa to 4.92 MPa. More importantly, the O-PASS nanofibrous membrane still exhibited high removal efficiency after high temperature, acid, alkali, or organic solvent treatments. Overall, O-PASS nanofibrous membranes are promising high-performance filter materials with high temperature and corrosion resistance.

Selective removal of toxic organic dyes using Trӧger base-containing sulfone copolymers made from a metal-free thiol-yne click reaction followed by oxidation

Three copolymers TCP1–3 bearing Trӧger's base (TB) units intercalated with various thioether groups were synthesized using a catalyst-free thiol-yne click reaction. TCP1–3 display excellent solubility in common organic solvents allowing for their structural, and photophysical characterization. The thioether groups in TCP1–3 were selectively oxidized into their respective sulfone derivatives under mild oxidation reaction conditions affording the postmodified copolymers TCP4–6. Investigation of organic dye uptake from water by TCP1–6 proved their efficiency as selective adsorbents removing up to 100% of the cationic dye methylene blue (MEB) when compared to anionic dyes, such as Congo red (CR), methyl orange (MO) and methyl blue (MB). The sulfone-containing copolymers TCP4–6 display superior and faster MEB removal efficiencies with respect to their corresponding synthons TCP1–3.

Copolymers TCP1–3 with Trӧger's base units and aryl thioether groups were made via a click reaction. Selective oxidation of the thioethers into sulfone groups afforded TCP4–6 which display up to 100% removal efficiency of methylene blue from water.

Segregated poly(arylene sulfide sulfone)/graphene nanoplatelet composites for electromagnetic interference shielding prepared by the partial dissolution method

Segregated conductive polymer composites have been proved to be outstanding electromagnetic interference shielding (EMI) materials at low filler loadings. However, due to the poor interfacial adhesion between the pure conductive filler layers and segregated polymer granules, the mechanical properties of the segregated composites are usually poor, which limit their application. Herein, a simple and effective approach, the partial dissolution method, has been proposed to fabricate segregated poly(arylene sulfide sulfone) (PASS)/graphene nanoplatelet (GNP) composites with superior EMI shielding effectiveness (SE) and high tensile strength. Morphology examinations revealed that the GNPs were restricted in the dissolved outer layer by the undissolved cores, and there was a strong interaction between the PASS/GNP layer and the pure PASS core. The resultant PASS/GNP composites showed excellent electrical conductivity (60.3 S m^-1) and high EMI SE (41 dB) with only 5 wt% GNPs. More notably, the tensile strength of the PASS/GNPs prepared by partial dissolution reached 36.4 MPa, presenting 136% improvement compared to that of the conventional segregated composites prepared by mechanical mixing. The composites also exhibited high resistance to elevated temperatures and chemicals owing to the use of the special engineering polymer PASS as a matrix.

Functionalized poly(arylene ether sulfone) containing hydroxyl units for the fabrication of durable, superhydrophobic oil/water separation membranes

The stability of superhydrophobicity is crucial for the long-term application of an oil/water separation membrane in harsh environments such as high temperatures and various aggressive solvents. However, achieving such a stable superhydrophobic membrane remains a challenge. In this study, high performance fibrous oil/water separation membranes with a highly stable superhydrophobicity were fabricated by designing a functional polymer containing hydroxyl units. The reaction of hydroxy groups in poly(arylene ether sulfone) with octadecyltrichlorosilane (OTS) produces stable covalent interactions, which greatly enhance the stability of OTS on the PAES-OH (polyarylene ether sulfone containing hydroxy units) fibrous membrane fabricated by electrospinning, thus improving the stability of superhydrophobicity of the membrane. The stability of the OTS layer was characterized by FT-IR, SEM and water contact angle measurement. The results suggest that OTS is highly stable on a PAES-OH membrane, while OTS on a polyethersulfone (PES) fibrous membrane is detached from the fiber during ultrasonic cleaning. The obtained membrane is superhydrophobic, with a water contact angle (CA) as high as 159.2° and a threshold sliding angle (TSA) as low as 7.8° even after ultrasonic cleaning for 3 h. In addition, the oil/water separation experiments indicate that this membrane has an excellent performance in the separation of oil from oil/water mixtures, and oil/water emulsions: the gravity driven flux is 7260-8720 L (m2 h)-1 and the water rejection is over 99%. This study provides a new approach for fabricating oil/water separation membranes with highly stable superhydrophobic properties from the perspective of designing new polymers.

Tailoring the Performance of Organic Solvent Nanofiltration Membranes with Biophenol Coatings

This study reports a systematic investigation of fine-tuning the filtration performance of nanofiltration membranes with biophenol coatings to produce solvent-resistant membranes with 390-1550 g mol-1 molecular weight cutoff (MWCO) and 0.5-40 L m-2 h-1 bar-1 permeance. Six kinds of inexpensive, commercial biophenols (dopamine, tannic acid, vanillyl alcohol, eugenol, morin, and quercetin) were subjected to identical oxidant-promoted polymerization to coat six kinds of loose asymmetric membrane supports: polyimide (PI), polyacrylonitrile (PAN), polysulfone (PSf), polyvinylidene difluoride (PVDF), polybenzimidazole (PBI), and polydimethylsiloxane (PDMS). The coatings were characterized by Fourier-transform infrared spectroscopy (FTIR), and the morphologies were characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The long-term stability of 42 membranes were tested in 12 organic solvents, including emerging green solvents MeTHF and Cyrene. The biophenol coatings led to tighter membranes with a decrease in MWCO of 12-79% at a penalty of a 22-92% permeance decrease in acetone.