Effects of GO and MOF@GO on the permeation and antifouling properties of cellulose acetate ultrafiltration membrane

Effect of degree of polymerization on regenerated cellulose ultrafiltration membrane performance through ZnCl2/AlCl3 aqueous solvent system

The development of a direct method for preparing regenerated cellulose (RC) ultrafiltration membranes from cellulose is urgently needed. In this study, refined cotton was used as the raw material to successfully prepare RC ultrafiltration membranes at room temperature using a ZnCl2/AlCl3 solvent system combined with a nonsolvent-induced phase separation (NIPS) method. This solvent system effectively degrades cellulose, producing RC ultrafiltration membranes with varying degrees of polymerization (DP). The research results indicate that reducing the DP of cellulose significantly decreases the viscosity of the solution, facilitating the formation of an asymmetric, finger-like pore structures in the membrane. Furthermore, a decrease in DP slightly enlarges the surface pore size and significantly thickens the dense layer. At a DP of 250, the water flux of the DP250-ET membrane reached 630 L·m-2·h-1·bar-1, with a molecular weight cut-off (MWCO) of ~300 kDa, enabling efficient separation of viruses (LRV > 3.91) and IgG. The exposure of more hydroxy groups on the RC enhances the membrane's hydrophilicity, indicated by a water contact angle (WCA) of 39.5°. Compared to commercial polyethersulfone (PES) membranes, the DP250-ET membrane exhibited lower protein adsorption and excellent anti-fouling performance in practical applications (FRR > 80 %). Overall, this work confirms the significant potential of the eco-friendly ZnCl2/AlCl3 solvent system in the fabrication of RC ultrafiltration membranes, where the structure and performance of the membrane can be tailored by adjusting the DP of cellulose.

Maltodextrin-modified graphene oxide composite membrane applied to the enantioseparation of amino acids

The separation of enantiomers using chiral membranes has garnered much research interest. In this study, the enantioseparation of amino acids using chiral membranes, namely graphene oxide-ethylenediamine-maltodextrin (GO-EDA-MD) and GO-EDA-hydroxypropyl-MD (GO-EDA-HP-MD), was evaluated. HP-MD and MD were investigated as chiral selectors due to their inherent chirality. Various characterization techniques, including atomic force microscopy, Fourier transform infrared spectrometry, field emission scanning electron microscopy, water contact angle analysis, tensile properties, and thermal gravimetric analysis were employed to analyze the membrane structures. The evaluation of enantioseparation performance was conducted by employing tryptophan, phenylalanine, and tyrosine enantiomers. Optimal conditions for enantiomer separation were achived using a GO-EDA-HP-MD chiral composite (1.75 wt%), a feed concentration of 10 mg/L for each enantiomer, a separation time of 15 min, and a membrane effective surface area of 1.0 cm2. Also, the bovine serum albumin rejection was 90.0 %, and the water flux reached 37.1 L m-2 h-1. The highest enantiomeric excess (ee.%) values were 46.33 %, 76.97 %, and 73.04 % for tryptophan, phenylalanine, and tyrosine, respectively. The impact of voltage on ee.% and substance flux was also explored. This membrane was able to separate enantiomers successfully.

MOF-Based Membranes for Remediated Application of Water Pollution

Membrane separation plays a crucial role in the current increasingly complex energy environment. Membranes prepared by metal-organic framework (MOF) materials usually possess unique advantages in common, such as uniform pore size, ultra-high porosity, enhanced selectivity and throughput, and excellent adsorption property, which have been contributed to the separation fields. In this comprehensive review, we summarize various designs and synthesized strategies of free-standing MOF and composite MOF-based membranes for water treatment. Special emphases are given not only on the effects of MOF on membrane performance, removal efficiencies, and elimination mechanisms, but also on the importance of MOF-based membranes for the applications of oily and micro-pollutant removal, adsorption, separation, and catalysis. The challenges and opportunities in the future for the industrial implementation of MOF-based membranes are also discussed.

Development and Study of Novel Ultrafiltration Membranes Based on Cellulose Acetate

Recently, increasing attention of researchers in the field of membrane technology has been paid to the development of membranes based on biopolymers. One of the well-proven polymers for the development of porous membranes is cellulose acetate (CA). This paper is devoted to the study of the influence of different parameters on ultrafiltration CA membrane formation and their transport properties, such as the variation in coagulation bath temperature, membrane shrinkage (post-treatment at 80 °C), introduction to casting CA solution of polymers (polyethylene glycol (PEG), polysulfone (PS), and Pluronic F127 (PL)) and carbon nanoparticles (SWCNTs, MWCNTs, GO, and C60). The structural and physicochemical properties of developed membranes were studied by scanning electron and atomic force microscopies, Fourier-transform infrared spectroscopy, X-ray photoelectron spectroscopy, and contact angle measurements. The transport properties of developed CA-based membranes were evaluated in ultrafiltration of bovine serum albumin (BSA), dextran 110 and PVP K-90. All developed membranes rejected 90% compounds with a molecular weight from ~270,000 g/mol. It was shown that the combination of modifications (addition of PEG, PS, PL, PS-PL, and 0.5 wt% C60) led to an increase in the fluxes and BSA rejection coefficients with slight decrease in the flux recovery ratio. These changes were due to an increased macrovoid number, formation of a more open porous structure and/or thinner top selective, and decreased surface roughness and hydrophobization during C60 modification of blend membranes. Optimal transport properties were found for CA-PEG+C60 (the highest water-394 L/(m2h) and BSA-212 L/(m2h) fluxes) and CA-PS+C60 (maximal rejection coefficient of BSA-59%) membranes.

The Application of Metal-Organic Frameworks in Water Treatment and Their Large-Scale Preparation: A Review

Over the last few decades, there has been a growing discourse surrounding environmental and health issues stemming from drinking water and the discharge of effluents into the environment. The rapid advancement of various sewage treatment methodologies has prompted a thorough exploration of promising materials to capitalize on their benefits. Metal-organic frameworks (MOFs), as porous materials, have garnered considerable attention from researchers in recent years. These materials boast exceptional properties: unparalleled porosity, expansive specific surface areas, unique electronic characteristics including semi-conductivity, and a versatile affinity for organic molecules. These attributes have fueled a spike in research activity. This paper reviews the current MOF-based wastewater removal technologies, including separation, catalysis, and related pollutant monitoring methods, and briefly introduces the basic mechanism of some methods. The scale production problems faced by MOF in water treatment applications are evaluated, and two pioneering methods for MOF mass production are highlighted. In closing, we propose targeted recommendations and future perspectives to navigate the challenges of MOF implementation in water purification, enhancing the efficiency of material synthesis for environmental stewardship.

Droplet Manipulation on Bioinspired Slippery Surfaces: From Design Principle to Biomedical Applications

Droplet manipulation with high efficiency, high flexibility, and programmability, is essential for various applications in biomedical sciences and engineering. Bioinspired liquid-infused slippery surfaces (LIS), with exceptional interfacial properties, have led to expanding research for droplet manipulation. In this review, an overview of actuation principles is presented to illustrate how materials or systems can be designed for droplet manipulation on LIS. Recent progress on new manipulation methods on LIS is also summarized and their prospective applications in anti-biofouling and pathogen control, biosensing, and the development of digital microfluidics are presented. Finally, an outlook is made on the key challenges and opportunities for droplet manipulation on LIS.

Nanocelluloses fine-tuned polyvinylidene fluoride (PVDF) membrane for enhanced separation and antifouling

To mitigate membrane fouling and address the trade-off between permeability and selectivity, we fabricated nanocellulose (NC) fine-tuned polyvinylidene fluoride (PVDF) porous membranes (NC-PVDFs) using phase inversion method through blending NCs with varied aspect ratios, surface charges and grafted functional groups. NC-PVDF presented rougher surface (increased by at least 18.3 %), higher porosity and crystallinity compared to PVDF membrane. Moreover, cellulose nanocrystals incorporated PVDF (CNC-PVDF) elevated membrane surface charge and hydrophilicity (from 74.3° to 71.7°), while 2,2,6,6-tetramethylpiperidine-1-oxyl-oxidized cellulose nanofibers modified PVDF (TCNF-PVDF) enhanced the porosity (from 25.0 % to 40.3 %) and tensile strength (63.6 % higher than PVDF). For separation performance, NC improved flux, rejection and fouling resistance due to facilitation of phase transition thermokinetics as pore-forming agent and increased hydrophilicity at both interface and pore wall. For water flux, NC-PVDFs (139-228 L·m-2·h-1) resulted in increased permeability compared to bare PVDF. CNC-PVDF membrane exhibited the highest water flux because of improved porosity, roughness and hydrophilicity. For bovine serum albumin (BSA) rejection, the removal rates of all NC-PVDFs were all above 90 %. Notably, TCNF-PVDF exhibited the most remarkable elevation of BSA rejection (95.1 %) owing to size exclusion and charge repulsion in comparison with PVDF.

Poloxamer 407 Combined with Polyvinylpyrrolidone To Prepare a High-Performance Poly(ether sulfone) Ultrafiltration Membrane

At present, the design and fabrication of polymer membranes with high permeability and good retention ability are still huge challenges. In this study, the commercial Poloxamer 407 (Pluronic F127) is selected as a multifunctional additive, and polyvinylpyrrolidone is used as a pore-forming agent to modify the poly(ether sulfone) membrane by liquid-liquid phase conversion technology to prepare an ultrafiltration membrane with excellent performance. The hydrophobic poly(propylene oxide) segment in Poloxamer 407 guarantees that this copolymer can be firmly anchored to the poly(ether sulfone) matrix, and the hydrophilic poly(ethylene oxide) segments in Poloxamer 407 impart a stronger hydrophilic nature to the modified membrane surface. Therefore, the permeability and hydrophilicity of the modified membrane are significantly improved and the modified membrane also has good stability. When the amount of Poloxamer 407 added to the casting solution reached 0.6 g, the water flux of the modified membrane was as high as 368 L m-2 h-1, and the rejection rate of bovine serum albumin was close to 98%. In the test to isolate organic small molecule dyes, the retention rate of the modified membrane to Congo red is 94.27%. In addition, the modified membrane shows an excellent water flux recovery rate and antifouling ability. It performs well in subsequent cycle tests and long-term membrane life tests and can be used repeatedly. Our work has resulted in poly(ether sulfone) membranes with good performance, which show great potential in the treatment of biomedical wastewater and the removal of industrial organic dye wastewater, it provides ideas for the development and application of amphiphilic polymer materials.

Hybrid porous material supported in a cellulose acetate polymeric membrane for the direct immersion thin-film microextraction of parabens in water

A simple and sensitive direct immersion thin-film microextraction (DI-TFME) method based on MIL-101(Cr) modified with carbon nanofibers supported in cellulose acetate (CA-MIL-101(Cr)@CNFs) polymeric membrane was developed for the extraction and preconcentration of parabens in environmental water samples. A high-performance liquid chromatography-diode array detector (HPLC-DAD) was used for the determination and quantification of methylparaben (MP) and propylparaben (PP). The factors affecting the DI-TFME performance were investigated using central composite design (CCD). The linearity of the DI-TFME/HPLC-DAD method obtained under optimal conditions was 0.04-0.04-500 µg/L with a correlation coefficient (R2) greater than 0.99, respectively. The limits of detection (LOD) and quantification (LOQ) for methylparaben were 11 ng/L and 37 ng/L; for propylparaben, they were 13 ng/L and 43 ng/L, respectively. The enrichment factors were 93.7 and 123 for methylparaben and propylparaben. The intraday (repeatability) and interday (reproducibility) precisions expressed as relative standard deviations (%RSD) were less than 5%. Furthermore, the DI-TFME/HPLC-DAD method was validated using real water samples spiked with known concentrations of the analytes. The recoveries ranged from 91.5 to 99.8%, and intraday and interday trueness values were less than ±15%. The DI-TFME/HPLC-DAD approach was effectively used for the preconcentration and quantification of parabens in river water and wastewater samples.

Preparation, characterization, and performance evaluation of composite films of polyvinyl alcohol/ cellulose nanofiber extracted from Imperata cylindrica

In recent years, production of cellulose nanofiber (CNF) from waste materials has achieved great interest owing to their renewable nature, biodegradability, high mechanical properties, economic value, and low density. Because Polyvinyl alcohol (PVA) is a synthetic biopolymer with good water solubility and biocompatibility, the composite material formed of CNF and PVA, is a sustainable way of monetizing to address environmental and economic issues. In this work pure PVA, PVA/CNF0.5, PVA/CNF1.0, PVA/CNF1.5, and PVA/CNF2.0 nanocomposite films were produced using the solvent casting approach with the addition of 0, 0.5, 1.0, 1.5, and 2.0 wt% of CNF concentrations respectively. The strongest water absorption behaviour was found as 25.82% for pure PVA membrane, followed by PVA/CNF0.5 (20.71%), PVA/CNF1.0 (10.26%), PVA/CNF1.5 (9.63%), and PVA/CNF2.0 (4.35%). The water contact angle of 53.1°, 47.8°, 43.4°, 37.7°, and 32.3° was formed between water droplet and the solid-liquid interface of pure PVA, PVA/CNF0.5, PVA/CNF1.0, PVA/CNF1.5, PVA/CNF2.0 composite films respectively. The SEM image clearly shows that a network structure like a tree form at the PVA/CNF0.5 composite film, where the sizes and number of pores are apparent. XRD analysis suggested that unique peaks found at 2θ = 17.5°, 28.1°, 33.4°, and 38° for nanocomposites indicating new crystal plane generated upon cross-linking in presence of malic acid. The maximum loss rate temperature (T_d,max) for PVA/CNF0.5, PVA/CNF1.0, PVA/CNF1.5 was determined by TG analysis to be around 273.4 °C. FTIR studies suggested that PVA/CNF0.5 composite film showed the highest peak at 1428 cm^-1 as compared to other PVA/CNF composite films representing the presence of higher crystalline band in the composite film matrix. PVA/CNF0.5 composite film was found to have a surface porosity and mean pore size of 27.35% and 0.19 μm respectively, classifying it in the MF membrane category. The maximum tensile strength (TS) of 5.27 MPa was found for PVA/CNF0.5, followed by PVA/CNF1.0, PVA/CNF1.5, pure PVA, and PVA/CNF2.0. The maximum young's modulus (111 MPa) was found for PVA/CNF1.0, followed by PVA/CNF0.5, PVA/CNF2.0, PVA/CNF1.5, and pure PVA, which could be attributed to the cyclization of the molecular structures by cross-linking. PVA/CNF0.5 exhibits greater elongation at break (21.7) than the other polymers, indicating a material's ability to undergo significant deformation before failure. Performance evaluation of the PVA/CNF0.5 composite film showed that 46.3% and 92.8% yield were found in the retentate for 200 mg/L of BSA, and 5 × 10⁷ CFU/mL respectively. However, more than 90% E. coli was retained by PVA/CNF0.5 composite film, therefore absolute rating of this membrane is 0.22 μm. The size of this composite film may be therefore considered in the range of MF.

Functionally-designed floatable amino-modified ZnLa layered double hydroxides/cellulose acetate beads for tetracycline removal: Performance and mechanism

The over-reliance on tetracycline antibiotics (TC) in the animal husbandry and medical field has seriously affected the safety of the ecological environment. Therefore, how to effectively treat tetracycline wastewater has always been a long-term global challenge. Here, we developed a novel polyethyleneimine (PEI)/Zn-La layered double hydroxides (LDH)/cellulose acetate (CA) beads with cellular interconnected channels to strengthen the TC removal. The results of the exploration on its adsorption properties illustrated that the adsorption process exhibited a favorable correlation with the Langmuir model and the pseudo-second-order kinetic model, namely monolayer chemisorption. Among the many candidates, the maximum adsorption capacity of TC by 10 %PEI-0.8LDH/CA beads was 316.76 mg/g. Apart from that, the effects of pH, interfering species, actual water matrix and recycling on the adsorption of TC by PEI-LDH/CA beads were also analyzed to verify their superior removal capability. The potential for industrial-scale applications was expanded through fixed-bed column experiments. The proven adsorption mechanisms mainly included electrostatic interaction, complexation, hydrogen bonding, n-π EDA effect and cation-π interaction. The self-floating high-performance PEI-LDH/CA beads exploited in this work provided fundamental support for the practical application of antibiotic-based wastewater treatment.

Large-Area Fabrication of Ultrathin Metal-Organic Framework Membranes

Metal-organic framework (MOF)-based membranes, featuring potential molecular sieving effects and therefore capable of surmounting the ubiquitous trade-off between membrane selectivity and permeability, hold great promise for multitudinous chemical separations. Nevertheless, it remains highly challenging for the large-area fabrication of ultrathin MOF membranes with variable thickness, great homogeneity, and preferential orientation. Herein, this work reports the facile fabrication of ultrathin (down to 20 nm) NUS-8 membranes in large-area (>200 cm² ) yet with great homogeneity and texture along (00l) direction due to the superior solution processability of the as-synthesized NUS-8 nanosheets. The resultant NUS-8 membranes with good adhesion properties and certain flexibility exhibit excellent rejections (>98% for Mg²⁺ and Al³⁺ , and dyes with molecular weights larger than 585.5 g mol^-1 ) toward aqueous separation of various metal ions and dyes at modest permeance (1-3.2 L m^-2 h^-1 bar^-1 ) due to the well-aligned structures. Such separation performance outstands among polymetric membranes, thin-film composite membranes, mixed matrix membranes, and other MOF membranes reported in the literature. The separation mechanism is reasonably discussed based on the experimental and theoretical results. This study opens up novel perspectives for preparing ultrathin and large-area MOF membranes using the solution processability of MOFs.

Engineering Metal-Organic-Framework (MOF)-Based Membranes for Gas and Liquid Separation

Separation is one of the most energy-intensive processes in the chemical industry, and membrane-based separation technology contributes significantly to energy conservation and emission reduction. Additionally, metal-organic framework (MOF) materials have been widely investigated and have been found to have enormous potential in membrane separation due to their uniform pore size and high designability. Notably, pure MOF films and MOF mixed matrix membranes (MMMs) are the core of the "next generation" MOF materials. However, there are some tough issues with MOF-based membranes that affect separation performance. For pure MOF membranes, problems such as framework flexibility, defects, and grain orientation need to be addressed. Meanwhile, there still exist bottlenecks for MMMs such as MOF aggregation, plasticization and aging of the polymer matrix, poor interface compatibility, etc. Herein, corresponding methods are introduced to solve these problems, including inhibiting framework flexibility, regulating synthesis conditions, and enhancing the interaction between MOF and substrate. A series of high-quality MOF-based membranes have been obtained based on these techniques. Overall, these membranes revealed desired separation performance in both gas separation (e.g., CO2, H2, and olefin/paraffin) and liquid separation (e.g., water purification, organic solvent nanofiltration, and chiral separation).

Advances in Application of Cellulose-MOF Composites in Aquatic Environmental Treatment: Remediation and Regeneration

Metal organic frameworks (MOFs) have gained remarkable interest in water treatment due to their fascinating characteristics, such as tunable functionality, large specific surface area, customizable pore size and porosity, and good chemical and thermal stability. However, MOF particles tend to easily agglomerate in nanoscale, thus decreasing their activity and processing convenience. It is necessary to shape MOF nanocrystals into maneuverable structures. The in situ growth or ex situ incorporation of MOFs into inexpensive and abundant cellulose-family materials can be effective strategies for the stabilization of these MOF species, and therefore can make available a range of enhanced properties that expand the industrial application possibilities of cellulose and MOFs. This paper provides a review of studies on recent advances in the application of multi-dimensional MOF-cellulose composites (e.g., aerogels, membranes, and bulk materials) in wastewater remediation (e.g., metals, dyes, drugs, antibiotics, pesticides, and oils) and water regeneration by adsorption, photo- or chemocatalysis, and membrane separation strategies. The advantages brought about by combining MOFs and cellulose are described, and the performance of MOF-cellulose is described and compared to its counterparts. The mechanisms of relative MOF-cellulose materials in processing aquatic pollutants are included. Existing challenges and perspectives for future research are proposed.

A critical review on graphene oxide membrane for industrial wastewater treatment

An important way to promote the environmental industry's goal of carbon reduction is to promote the recycling of resources. Membrane separation technology has unique advantages in resource recovery and advanced treatment of industrial wastewater. However, the great promise of traditional organic membrane is hampered by challenges associated with organic solvent tolerance, lack of oxidation resistance, and serious membrane fouling control. Moreover, the high concentrations of organic matter and inorganic salts in the membrane filtration concentrate also hinder the wider application of the membrane separation technology. The emerging cost-effective graphene oxide (GO)-based membrane with excellent resistance to organic solvents and oxidants, more hydrophilicity, lower membrane fouling, better separation performance has been expected to contribute more in industrial wastewater treatment. Herein, we provide comprehensive insights into the preparation and characteristic of GO membranes, as well as current research status and problems related to its future application in industrial wastewater treatment. Finally, concluding remarks and future perspectives have been deduced and recommended for the GO membrane separation technology application for industrial wastewater treatment, which leads to realizing sustainable wastewater recycling and a nearly "zero discharge" water treatment process.

Facile preparation of pH-sensitive biocompatible alginate beads havening layered double hydroxide supported metal-organic framework for controlled release from doxorubicin to breast cancer cells

In the present study, a pH-sensitive controlled drug delivery system was prepared from alginate beads impregnated with AlCu layered double hydroxides (LDH) supported copper metal-organic framework (Alg-DOX-Cu MOF-LDH beads) for controlled release from doxorubicin (DOX) to breast cancer cells. The physicochemical properties of Alg-DOX-Cu MOF-LDH beads were determined by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), field emission scanning electron microscopy (FE-SEM), and Zeta potential. The in vitro release studies showed that the Alg-DOX-Cu MOF-LDH beads had more controlled drug release than the DOX-Cu MOF-LDH and in vitro release of DOX from both carriers showed pH-response release behavior. The kinetic adsorption studies also confirmed that the drug release from the DOX-Cu MOF-LDH and Alg-DOX-Cu MOF-LDH beads well obey the Korsmeyer-Peppas model. Meanwhile, in vitro cytotoxicity and DAPI tests on L929 (non-cancerous cells) and MCF-7 (human breast cancer cells) clearly showed that the prepared AlCu LDH and Cu MOF-LDH systems had good biocompatibility. Whereas, Alg-DOX-Cu MOF-LDH beads had higher cytotoxicity effects as a result of the controlled release of DOX to MCF-7 cells. These results suggested that the Alg-DOX-Cu MOF-LDH beads can be used as an excellent drug delivery system for cancer therapy and other biomedical applications.

Chitosan-based hollow nanofiber membranes with polyvinylpyrrolidone and polyvinyl alcohol for efficient removal and filtration of organic dyes and heavy metals

Due to their large specific surface area and numerous diffusion channels, hollow fibers are widely used in wastewater treatment. In this study, we successfully synthesized a chitosan (CS)/polyvinylpyrrolidone (PVP)/polyvinyl alcohol (PVA) hollow nanofiber membrane (CS/PVP/PVA-HNM) via coaxial electrospinning. This membrane demonstrated remarkable permeability and adsorption separation. Specifically, the CS/PVP/PVA-HNM had a pure water permeability of 4367.02 L·m^-2·h^-1·bar^-1. The hollow electrospun nanofibrous membrane exhibited a continuous interlaced nanofibrous framework structure with the extraordinary advantages of high porosity and high permeability. The rejection ratios of CS/PVP/PVA-HNM for Cu²⁺, Ni²⁺, Cd²⁺, Pb²⁺, malachite green (MG), methylene blue (MB) and crystal violet (CV) were 96.91 %, 95.29 %, 87.50 %, 85.13 %, 88.21 %, 83.91 % and 71.99 %, and the maximum adsorption capacities were 106.72, 97.46, 88.10, 87.81, 53.45, 41.43, and 30.97 mg·g^-1, respectively. This work demonstrates a strategy for the synthesis of hollow nanofibers, which provides a novel concept for the design and fabrication of highly efficient adsorption separation membranes.

Surface Engineering of a Bioartificial Membrane for Its Application in Bioengineering Devices

Membrane technology is playing a crucial role in cutting-edge innovations in the biomedical field. One such innovation is the surface engineering of a membrane for enhanced longevity, efficient separation, and better throughput. Hence, surface engineering is widely used while developing membranes for its use in bioartificial organ development, separation processes, extracorporeal devices, etc. Chemical-based surface modifications are usually performed by functional group/biomolecule grafting, surface moiety modification, and altercation of hydrophilic and hydrophobic properties. Further, creation of micro/nanogrooves, pillars, channel networks, and other topologies is achieved to modify physio-mechanical processes. These surface modifications facilitate improved cellular attachment, directional migration, and communication among the neighboring cells and enhanced diffusional transport of nutrients, gases, and waste across the membrane. These modifications, apart from improving functional efficiency, also help in overcoming fouling issues, biofilm formation, and infection incidences. Multiple strategies are adopted, like lysozyme enzymatic action, topographical modifications, nanomaterial coating, and antibiotic/antibacterial agent doping in the membrane to counter the challenges of biofilm formation, fouling challenges, and microbial invasion. Therefore, in the current review, we have comprehensibly discussed different types of membranes, their fabrication and surface modifications, antifouling/antibacterial strategies, and their applications in bioengineering. Thus, this review would benefit bioengineers and membrane scientists who aim to improve membranes for applications in tissue engineering, bioseparation, extra corporeal membrane devices, wound healing, and others.

Membrane Surface Modification via In Situ Grafting of GO/Pt Nanoparticles for Nitrate Removal with Anti-Biofouling Properties

Nanofiltration processes for the removal of emerging contaminants such as nitrate are a focus of attention of research works as an efficient technique for providing drinking water for people. Polysulfone (PSF) nanofiltration membranes containing graphene oxide (GO)/Pt (0, 0.25, 0.5, 0.75, 1 wt%) nanoparticles were generated with the phase inversion pathway. The as-synthesized samples were characterized by FTIR, SEM, AFM, and contact angle tests to study the effect of GO/Pt on hydrophilicity and antibacterial characteristics. The results conveyed that insertion of GO/Pt dramatically improved the biofouling resistance of the membranes. Permeation experiments indicated that PSF membrane embracing 0.75 wt% GO/Pt nanoparticles had the highest nitrate flux and rejection ability. The membrane's configuration was simulated using OPEN-MX simulating software indicating membranes maintaining 0.75 wt% of GO/Pt nanoparticles revealed the highest stability, which is well in accordance with experimental outcomes.

Zeolitic imidazolate framework (ZIF-8) modified cellulose acetate NF membranes for potential water treatment application

In this study, cellulose acetate (CA)-based nanofiltration membranes, modified with zeolitic imidazole framework-8 (ZIF-8) particles, were prepared with various ZIF-8 contents (0, 0.1, 0.25, 0.5, 1 and 2 wt%), to obtain membranes with improved flux and filtration performance by combining advantages of CA polymer and ZIF-8 metal-organic frameworks. Removal efficiency studies were carried out with bovine serum albumin and two different dyes, along with antifouling performance evaluation. Results of experiments disclosed that as the ZIF-8 ratio increased, the contact angle values decreased. With ZIF-8 addition, the pure water flux of the membranes increased. Besides, the flux recovery ratio value was approximately 85 % for the bare CA membrane, while it increased to above 90 % by blending ZIF-8. Also, in all ZIF-8 doped membranes, a fouling decrease was observed. Importantly, it was observed that the dye removal efficiency increased with the addition of ZIF-8 particles from 95.2 to 97.7 % for Reactive Black 5 dye.

Review on Metal-Organic Framework Classification, Synthetic Approaches, and Influencing Factors: Applications in Energy, Drug Delivery, and Wastewater Treatment

Metal ions or clusters that have been bonded with organic linkers to create one- or more-dimensional structures are referred to as metal-organic frameworks (MOFs). Reticular synthesis also forms MOFs with properly designated components that can result in crystals with high porosities and great chemical and thermal stability. Due to the wider surface area, huge pore size, crystalline nature, and tunability, numerous MOFs have been shown to be potential candidates in various fields like gas storage and delivery, energy storage, catalysis, and chemical/biosensing. This study provides a quick overview of the current MOF synthesis techniques in order to familiarize newcomers in the chemical sciences field with the fast-growing MOF research. Beginning with the classification and nomenclature of MOFs, synthesis approaches of MOFs have been demonstrated. We also emphasize the potential applications of MOFs in numerous fields such as gas storage, drug delivery, rechargeable batteries, supercapacitors, and separation membranes. Lastly, the future scope is discussed along with prospective opportunities for the synthesis and application of nano-MOFs, which will help promote their uses in multidisciplinary research.

Cellulose acetate based sustainable nanostructured membranes for environmental remediation

Membrane-based gas separation has a great potential for reducing environmentally hazardous carbon dioxide (CO₂) gas. The polymeric membranes developed for CO₂ capturing have some limitations in their selectivity and permeability. There is a need to overcome these issues and developed such membranes having high-performance CO₂ capture with cost-effectiveness. The present study aimed to synthesize mixed matrix membranes (MMMs) having improved properties CO₂ adsorption performance and stability than that of pure polymer. Further, the effect on CO₂ adsorption by increasing the filler concentration in MMMs was investigated. The MMMs were synthesized by incorporating (1-5 wt%) Cu-MOF-GO composites as filler into cellulose-acetate (CA) polymer matrix by adopting the solution casting method. The performance of MMMs was studied by changing the Cu-MOF-GO composite concentration (1-5 wt%) in the polymer matrix at 45 °C up to 15 bar. Morphological analysis by using SEM confirms that by increasing the concentration of Cu-MOF-GO more than 3% will result in their agglomeration in MMM. The successful incorporation of MOF within the polymer matrix of MMMs was confirmed through the presence of functional groups using FTIR and Raman spectroscopy. XRD analysis revealed that pure CA changes its semi-crystalline behaviour into crystalline by the addition of Cu-MOF-GO. The maximum tensile stress and strain rate of MMMs was 45.1 N/mm² and 12.8%. In addition, with an increase in (4-5 wt%) Cu-MOF-GO concentration the hydrophilicity of MMMs decreases. The maximum uptake rate of CO₂ was 1.79 mmol/g and 7.98 wt% at 15 bar. The adsorption results conclude that Cu-MOF-GO composite and CA-based MMM can be effective for CO₂ capture.

Preparation, characterization, and performance of PES/GO woven mixed matrix nanocomposite forward osmosis membrane for water desalination

Mixed matrix woven forward osmosis (MMWFO) membranes made of polyethersulfone (PES)/graphene oxide nanosheets (GO NSs) were made by inserting varying wt% ratios of GO NSs (zero to 0.1 wt%) into the PES matrix. A coated woven fabric material was used to cast the membrane polymer solution. The physical characteristics and chemical structures of the produced PES/GO MMWFO membranes were studied, including contact angle, hydrophilicity, porosity, tortuosity, function groups, chemical and crystallographic structures, nanomorphologies, and surface roughness. The performance of the prepared PES/GO FO membranes for water desalination was evaluated in terms of pure water flux (J w), reverse salt flux (J s), and salt rejection (SR). The hydrophilicity and porosity of the FO membrane improved with the addition of GO NSs, as did water permeability due to the development of multiple skin-layer structures with greater GO NS loading. These GO NSs establish shortcut pathways for water molecules to move through, reducing support layer tortuosity by three times, lowering support layer structural features, and minimizing internal concentration polarization (ICP). The PES/0.01 wt% GO MMWFO membrane with a total casting thickness of 215 μm and 1 M NaCl concentration had the best performance, with the highest J w (114.7 LMH), lowest J s (0.03 GMH), and lowest specific reverse solute flux (J s/J w = 0.00026 g L-1), as well as a more favorable structural parameter (S = 149 μm). The performance of our optimized membrane is significantly better than that of the control woven commercial cellulose triacetate (CTA) FO membrane under optimal FO conditions. As the NaCl concentration increased from 0.6 to 2 M, J w increased from 105 to 127 LMH which is much higher than the J w of the commercial one (7.2 to 15 LMH). Our FO membranes have an SR of 99.2%@0.65 M NaCl, which is significantly greater than that of the CTA membrane.

Cross-linked laminar graphene oxide membranes for wastewater treatment and desalination: A review

Two-dimensional (2D) lamellar graphene oxide (GO) membranes are emerging as attractive materials for molecular separation in water treatment because of their single atomic thickness, excellent hydrophilicity, large specific surface areas, and controllable properties. To yet, commercialization of GO laminar membranes has been hindered by their propensity to swell in hydrated conditions. Thus, chemical crosslinking of GO sheets with the polymer matrix is used to improve GO membrane hydration stability. This review focuses on pertinent themes such as how chemical crosslinking improves the hydration stability, separation performance, and antifouling properties of GO membranes.

The Growth of Metal–Organic Frameworks in the Presence of Graphene Oxide: A Mini Review

Integrated metal–organic frameworks (MOFs) with graphene oxide (GO) have aroused huge interest in recent years due to their unique properties and excellent performance compared to MOFs or GO alone. While a lot of attention has been focused on the synthesis methodologies and the performance analysis of the composite materials in recent years, the fundamental formation/crystallization mechanism(s) is (are) still not fully understood. Ascribed to the distinctive structural and functional properties of GO, the nucleation and crystallization process of MOFs could be altered/promoted, forming MOF/GO composite materials with different nanostructures. Furthermore, the MOF’s parental structure could also influence how the GO and MOF bond together. Thus, this short review attempted to provide critical and indepth discussions of recent research results with a particular focus on the factors that influence the directional growth of parent MOFs in the presence of graphene oxide. Due to the unique structure and enhanced properties, the derived MOF/GO composites have a wide range of applications including gas separation, electrochemistry, and photocatalysis. We hope this review will be of interest to researchers working on MOF design, crystal structure control (e.g., orientation), and composite materials development.

Cellulose acetate in fabrication of polymeric membranes: A review

Developing biodegradable polymers to fabricate filtration membranes is one of the main challenges of membrane science and technology. Cellulose acetate (CA) membranes, due to their excellent film-forming property, high chemical and mechanical stability, high hydrophilicity, eco-friendly, and suitable cost, are extensively used in water and wastewater treatment, gas separation, and energy generation purposes. The CA is one of the first materials used to fabricate filtration membranes. However, in the last decade, the possibility of modification of CA to improve permeability and stability has attracted the researcher's attention again. This review is focused on the properties of cellulose derivatives and especially CA membranes in the fabrication of polymeric separation membranes in various applications such as filtration, gas separation, adsorption, and ion exchange membranes. Firstly, a brief introduction of CA properties and used molecular weights in the fabrication of membranes will be presented. After that, different configurations of CA membranes will be outlined, and the performance of CA membranes in several applications and configurations as the main polymer and as an additive in the fabrication of other polymer-based membranes will be discussed.

Emerging advances and current applications of nanoMOF-based membranes for water treatment

Metal-organic frameworks (MOFs) are significantly tunable materials that can be exploited in a wide range of applications. In recent years, a large number of studies have been focused on synthesizing nano-scale MOFs (nanoMOFs), thus taking advantage of these unique materials in various applications, especially those that are only possible at nano-scale. One of the technologies where nanoMOF materials occupy a central role is the membrane technology as one of the most efficient separation techniques. Therefore, numerous reports can be found on the enhancement of the physicochemical properties of polymeric membranes by using nanoMOFs, leading to remarkably improved performance. One of the most considerable applications of these nanoMOF-based membranes is in water treatment systems, because freshwater scarcity is now an undeniable crisis facing humanity. In this in-depth review, the most prominent synthesis and post-synthesis methods for the fabrication of nanoMOFs are initially discussed. Afterwards, different nanoMOF-based composite membranes such as thin-film nanocomposites (TFN) and mixed-matrix membranes (MMM) and their various fabrication methods are reviewed and compared. Then, the impacts of using MOFs-based membranes for water purification through growing metal-organic frameworks crystals on the support materials and utilization of metal-organic frameworks as fillers in mixed matrix membrane (MMM) are highlighted. Finally, a summary of pros and cons of using nanoMOFs in membrane technology for water treatment purposes and clear future prospects and research potentials are presented.

Enhanced water flux and bacterial resistance in cellulose acetate membranes with quaternary ammoniumpropylated polysilsesquioxane

An enhanced water flux and anti-fouling nanocomposite ultrafiltration membrane based on quaternary ammoniumpropylated polysilsesquioxane (QAPS)/cellulose acetate (QAPS@CA) was fabricated by in situ sol-gel processing via phase inversion followed by quaternization with methyl iodide (CH₃I). Membrane characterizations were performed based on the contact angle, FTIR, SEM, and TGA properties. Membrane separation performance was assessed in terms of pure water flux, rejection, and fouling resistance. The 7%QAPS@CA nanocomposite membrane showed an increased wettability (46.6° water contact angle), water uptake (113%) and a high pure water permeability of ∼370 L m^-2 h^-1 bar^-1. Furthermore, the 7%QAPS@CA nanocomposite membrane exhibited excellent bactericidal properties (∼97.5% growth inhibition) against Escherichia coli (E. coli) compared to the bare CA membrane (0% growth inhibition). The 7%QAPS@CA nanocomposite membrane can be recommended for water treatment and biomedical applications.

Application of polysaccharide-based metal organic framework membranes in separation science

Polysaccharide/MOF composite membranes have captured the interests of many researchers during decontamination of polluted environments. Their popularity can be attributed to the relatively high chemical and thermal stabilities of these composite membranes. Chitosan is among the polysaccharides extensively used during the synthesis of hybrid membranes with MOFs. The applications of chitosan/MOF composite membranes in separation science are explored in detail in this paper. Researchers have also synthesised mixed matrix membranes of MOFs with cellulose and cyclodextrin that have proved to be effective during separation of a variety of materials. The uses of cellulose/MOF and cyclodextrin/MOF membranes for the removal of environmental pollutants are discussed in this review. In addition, the challenges associated with the use of these mixed matrix membranes are explored in this current paper.

Recent advances in dual-filler mixed matrix membranes

Mixed matrix membranes (MMMs) have been widely developed as an attractive solution to overcome the drawbacks found in most polymer membranes, such as permeability-selectivity trade-off and low physicochemical stability. Numerous fillers based on inorganic, organic, and hybrid materials with various structures including porous or nonporous, and two-dimensional or three-dimensional, have been used. Demanded to further improve the characteristics and performances of the MMMs, the use of dual-filler instead of a single filler has then been proposed, from which multiple effects could be obtained. This article aims to review the recent development of MMMs with dual filler and discuss their performances in diverse potential applications. Challenges in this emerging field and outlook for future research are finally provided.

Recent advances in metal-organic framework membranes for water treatment: A review

Among many separation membranes reported to date, the favorable polymer affinity and unique physio-chemical performances of metal-organic frameworks (MOFs) including ultra-high surface area, regular and highly controlled porosity have drawn widespread attention in industrial and academic communities. In this comprehensive review, the developmental timeline of MOF containing membranes for water treatment were clarified. The removal efficiencies, elimination mechanisms, as well as possible influencing factors of various MOF containing membranes that applied to water treatment were systematically summarized. The excellent removal performances of MOF containing membranes for various pollutants were determined by the size-exclusion, π-π stacking interaction, electrostatic interaction, hydrogen bonding and so on. Since the progress of engineered MOF containing membranes for practical wastewater treatment applications lags, we further analyzed the potential environmental application of MOF containing membranes from four aspects (stability of MOFs, antifouling performance of membranes, compatibility between MOF fillers and polymer matrix, dispersity of MOF nanoparticles in matrix), hoping to provide some meaningful insights.

Bimetallic Ag-Zn-BTC/GO composite as highly efficient photocatalyst in the photocatalytic degradation of reactive yellow 145 dye in water

Ag_x-Zn_100-x-BTC/GO composites (BTC: benzene-1,3,5-tricarboxylic, GO: graphene oxide) with different Ag/Zn molar ratios were synthesized using microwave-assisted hydrothermal treatment. The Ag_x-Zn_100-x-BTC/GO exhibited excellent photocatalytic performance in the reactive yellow 145 dye (RY-145) degradation under irradiation of visible light with nearly 100% of RY-145 removal after 35 min, as compared to Zn-BTC/GO and Ag-BTC/GO. Reactive oxygen species scavenging assays have shown that the holes (h⁺) and superoxide radical anion (O₂^-•) play a primary role in RY-145 degradation. Based on the band structure of materials, the Z-scheme photocatalytic mechanism was suggested. The effect of catalyst dosage, pH and dye concentration on the efficiency of photocatalytic activity of bimetallic Ag₅₀-Zn₅₀-BTC/GO was also investigated. The improvement in photocatalytic activity of bimetallic Ag₅₀-Zn₅₀-BTC/GO could be given by the synergism of (i) absorption of visible light confirmed by UV-Vis diffuse reflectance spectra; (ii) the increased lifetime as evidenced by photoluminescence spectra and transient photocurrent response; (iii) the increased oxygen vacancy defects as confirmed by X-ray photoelectron spectroscopy results. The degradation pathway of RY-145 dye was also predicted based on liquid chromatography-mass spectrometer analysis. The removed chemical oxygen demand, biological oxygen demand, total organic carbon outcomes indicated the high mineralization ability for RY-145 degradation over Ag₅₀-Zn₅₀-BTC/GO.