Modifying ceramic membranes with in situ grown iron oxide nanoparticles and their use for oily water treatment

A comprehensive review on state-of-the-art antifouling super(wetting and anti-wetting) membranes for oily wastewater treatment

One of the most dangerous types of pollution to the environment is oily wastewater, which is produced from a number of industrial sources and can cause damage to the environment, people, and creatures. To overcome this issue, membrane technology as an advanced method has been considered for treating oily wastewater due to its stability, high removal efficiency, and simplicity in scaling up. Membrane fouling, or the accumulation of oil droplets at or within the membrane pores, compromises the efficiency of membrane separation and water flux. In the last decade, the fabrication of membranes with specific wettability to reduce fouling has received much consideration. The purpose of this article is to offer a literature overview of all fabricated anti-fouling super(wetting and anti-wetting) membranes for applicable membrane processes for the separation of immiscible and emulsified oil/water mixtures. In this review, we first explain membrane fouling and discuss methods for preventing it. Afterwards, in all membrane separation processes, including pressure-driven, gravity-driven, and thermal-driven, membranes based on the form and density of oil are categorized as oil-removing or water-removing with special wettability, and then their wettability modification with different materials is particularly discussed. Finally, the prospect of anti-fouling membrane fabrication in the future is presented.

Enhanced Antifouling in Flat-Sheet Polyphenylsulfone Membranes Incorporating Graphene Oxide-Tungsten Oxide for Ultrafiltration Applications

In this study tungsten oxide and graphene oxide (GO-WO_2.89) were successfully combined using the ultra-sonication method and embedded with polyphenylsulfone (PPSU) to prepare novel low-fouling membranes for ultrafiltration applications. The properties of the modified membranes and performance were investigated using Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), contact angle (CA), water permeation flux, and bovine serum albumin (BSA) rejection. It was found that the modified PPSU membrane fabricated from 0.1 wt.% of GO-WO_2.89 possessed the best characteristics, with a 40.82° contact angle and 92.94% porosity. The permeation flux of the best membrane was the highest. The pure water permeation flux of the best membrane showcased 636.01 L·m^-2·h^-1 with 82.86% BSA rejection. Moreover, the membranes (MR-2 and MR-P2) manifested a higher flux recovery ratio (FRR %) of 92.66 and 87.06%, respectively, and were less prone to BSA solution fouling. The antibacterial performance of the GO-WO_2.89 composite was very positive with three different concentrations, observed via the bacteria count method. These results significantly overtake those observed by neat PPSU membranes and offer a promising potential of GO-WO_2.89 on activity membrane performance.

Nanofibrous/biopolymeric membrane a sustainable approach to remove organic micropollutants: A review

Aquifers are severely polluted with organic and inorganic pollutants, posing a serious threat to the global ecological system's balance. While various traditional methods are available, the development of innovative methods for effluent treatment and reuse is critical. Polymers have recently been widely used in a variety of industry sectors due to their unique properties. Biopolymers are a biodegradable material that is also a viable alternative to synthetic polymers. Biopolymers are preferably obtained from cellulose and carrageenan molecules from various biological sources. While compared with conventional non-biodegradable polymeric materials, the biopolymer possesses unique characteristics such as renewability, cost-effectiveness, biodegradability, and biocompatibility. The improvements towards the biopolymeric (natural) membranes have also been thoroughly discussed. The use of nanofillers to stabilise and improve the effectiveness of biopolymeric membranes in the elimination of organic pollutants is one of the most recent developments. This was discovered that the majority of biopolymeric membranes technology consolidated on organic pollutants. More research should be directed toward against emerging organic/persistent organic pollutants (POP) and micropollutants. Furthermore, processes for regenerating and reusing utilized biopolymer-based carbon - based materials are emphasized.

TiO2 ceramic membrane decorated with Fe3O4-Ag composite nanoparticles for produced water treatment

This study focused on the surface modification of commercial TiO₂ membranes with Fe₃O₄ decorated silver (Ag) nanoparticles (Fe₃O₄-Ag) via chemical attachment. Firstly, the Ag concentration on Fe₃O₄ was optimized, and different composites were prepared and characterized. Secondly, the optimal composite was used to prepare novel TiO₂/Fe₃O₄-Ag ceramic membranes via surface coating through tetraethyl orthosilicate (TEOS) crosslinking. The membranes were characterized using SEM, EDX, FTIR, XRD, and contact angle. Biofouling resistance of the membranes was investigated using the Coomassie Blue dye method. The coated membranes were tested for water flux, chemical oxygen demand (COD) rejection, and biofouling resistance. Results showed that all coated membranes exhibited higher water flux. For example, the membrane with a 1.25 wt% Fe₃O₄-Ag coating showed the highest filtration flux of 1445 L/m²h (LMH) compared to the pristine membrane (379 LMH) without compromising the COD rejection. The resistance of the membrane to biofouling increased with the increase of Fe₃O₄-Ag nanoparticle concentration. The obtained results demonstrate the great potential of TiO₂/Fe₃O₄-Ag ceramic membranes for the treatment of produced water.

Colloidal nanomaterials for water quality improvement and monitoring

Water is the most important resource for all kind forms of live. It is a vital resource distributed unequally across different regions of the globe, with populations already living with water scarcity, a situation that is spreading due to the impact of climate change. The reversal of this tendency and the mitigation of its disastrous consequences is a global challenge posed to Humanity, with the scientific community assuming a major obligation for providing solutions based on scientific knowledge. This article reviews literature concerning the development of nanomaterials for water purification technologies, including collaborative scientific research carried out in our laboratory (nanoLAB@UA) framed by the general activities carried out at the CICECO-Aveiro Institute of Materials. Our research carried out in this specific context has been mainly focused on the synthesis and surface chemical modification of nanomaterials, typically of a colloidal nature, as well as on the evaluation of the relevant properties that arise from the envisaged applications of the materials. As such, the research reviewed here has been guided along three thematic lines: 1) magnetic nanosorbents for water treatment technologies, namely by using biocomposites and graphite-like nanoplatelets; 2) nanocomposites for photocatalysis (e.g., TiO2/Fe3O4 and POM supported graphene oxide photocatalysts; photoactive membranes) and 3) nanostructured substrates for contaminant detection using surface enhanced Raman scattering (SERS), namely polymers loaded with Ag/Au colloids and magneto-plasmonic nanostructures. This research is motivated by the firm believe that these nanomaterials have potential for contributing to the solution of environmental problems and, conversely, will not be part of the problem. Therefore, assessment of the impact of nanoengineered materials on eco-systems is important and research in this area has also been developed by collaborative projects involving experts in nanotoxicity. The above topics are reviewed here by presenting a brief conceptual framework together with illustrative case studies, in some cases with original research results, mainly focusing on the chemistry of the nanomaterials investigated for target applications. Finally, near-future developments in this research area are put in perspective, forecasting realistic solutions for the application of colloidal nanoparticles in water cleaning technologies.

Alternative methods for cleaning membranes in water and wastewater treatment

Membrane fouling is caused by foulant deposition or adsorption through physical or chemical interactions on the membrane surface, causing the reduction of flux through the membrane. The main drawbacks of chemical agents used for cleaning are cost, damage caused on the membrane, and waste stream making the process unattractive. Alternative, methods such as ultrasound, enzymatic process, and osmotic backwashing were explored for membrane cleaning. Among all mentioned methods, micronanobubbles have been reported as a promising and emergent method for membrane surface cleaning; unfortunately, the information is limited, but preliminary studies have shown it as an efficient, cheap, and environmentally friendly technique. Other methods like electrically and vibratory-enhanced membrane cleaning also could be interesting but currently are unexplored and information is limited. PRACTITIONER POINTS: Chemical cleaning is an efficient option; however, from an environmental point of view, it is not attractive, and high concentrations could cause damage to the membrane. Micronanobubbles are an emergent and suitable technology for membrane and surface cleaning. Membrane modification and functionalization avoid membrane fast fouling, and the cleaning process is easier, but the manufacture cost could be expensive.

Recent Progress on Nanomaterial-Based Membranes for Water Treatment

Nanomaterials have emerged as the new future generation materials for high-performance water treatment membranes with potential for solving the worldwide water pollution issue. The incorporation of nanomaterials in membranes increases water permeability, mechanical strength, separation efficiency, and reduces fouling of the membrane. Thus, the nanomaterials pave a new pathway for ultra-fast and extremely selective water purification membranes. Membrane enhancements after the inclusion of many nanomaterials, including nanoparticles (NPs), two-dimensional (2-D) layer materials, nanofibers, nanosheets, and other nanocomposite structural materials, are discussed in this review. Furthermore, the applications of these membranes with nanomaterials in water treatment applications, that are vast in number, are highlighted. The goal is to demonstrate the significance of nanomaterials in the membrane industry for water treatment applications. It was found that nanomaterials and nanotechnology offer great potential for the advancement of sustainable water and wastewater treatment.

State-of-the-Art Ceramic Membranes for Oily Wastewater Treatment: Modification and Application

Membrane filtration is considered to be one of the most promising methods for oily wastewater treatment. Because of their hydrophilic surface, ceramic membranes show less fouling compared with their polymeric counterparts. Membrane fouling, however, is an inevitable phenomenon in the filtration process, leading to higher energy consumption and a shorter lifetime of the membrane. It is therefore important to improve the fouling resistance of the ceramic membranes in oily wastewater treatment. In this review, we first focus on the various methods used for ceramic membrane modification, aiming for application in oily wastewater. Then, the performance of the modified ceramic membranes is discussed and compared. We found that, besides the traditional sol-gel and dip-coating methods, atomic layer deposition is promising for ceramic membrane modification in terms of the control of layer thickness, and pore size tuning. Enhanced surface hydrophilicity and surface charge are two of the most used strategies to improve the performance of ceramic membranes for oily wastewater treatment. Nano-sized metal oxides such as TiO2, ZrO2 and Fe2O3 and graphene oxide are considered to be the potential candidates for ceramic membrane modification for flux enhancement and fouling alleviation. The passive antifouling ceramic membranes, e.g., photocatalytic and electrified ceramic membranes, have shown some potential in fouling control, oil rejection and flux enhancement, but have their limitations.