Flexible cationic side chains for enhancing the hydroxide ion conductivity of olefinic-type copolymer-based anion exchange membranes: An experimental and theoretical study

Low Pt loading for high-performance fuel cell electrodes enabled by hydrogen-bonding microporous polymer binders

A key challenge for fuel cells based on phosphoric acid doped polybenzimidazole membranes is the high Pt loading, which is required due to the low electrode performance owing to the poor mass transport and severe Pt poisoning via acid absorption on the Pt surface. Herein, these issues are well addressed by design and synthesis of effective catalyst binders based on polymers of intrinsic microporosity (PIMs) with strong hydrogen-bonding functionalities which improve phosphoric acid binding energy, and thus preferably uphold phosphoric acid in the vicinity of Pt catalyst particles to mitigate the adsorption of phosphoric acid on the Pt surface. With combination of the highly mass transport microporosity, strong hydrogen-bonds and high phosphoric acid binding energy, the tetrazole functionalized PIM binder enables an H₂-O₂ cell to reach a high Pt-mass specific peak power density of 3.8 W mg_Pt^-1 at 160 °C with a low Pt loading of only 0.15 mg_Pt cm^-2.

Influence of Membrane Fouling and Reverse Salt Flux on Membrane Impedance of Forward Osmosis Microbial Fuel Cell

The forward osmosis membrane (FO membrane) is an emerging wastewater treatment technology in bioelectricity generation, organic substrate removal and wastewater reclamation. Compared with traditional membrane materials, the FO membrane has a more uniform water content distribution and internal solution concentration distribution. In the past, it was believed that one of the important factors restricting power generation was membrane fouling. This study innovatively constructed a mass transfer model of a fouling membrane. Through the analysis of the hydraulic resistance coefficient and the salt mass transfer resistance coefficient, the driving force and the tendency of reverse salt flux during membrane fouling were determined by the model. A surprising discovery was that the fouling membrane can also achieve efficient power generation. The results showed that the hydraulic resistance coefficient of the fouling membrane increased to 4.97 times the initial value, while the salt mass transfer resistance coefficient did not change significantly. Meanwhile, membrane fouling caused concentration polarization in the FO membrane, which enhanced the reverse trend of salt, and the enhancement effect was significantly higher than the impact of the water flux decline caused by membrane pollution. This will make an important contribution to research on FO membrane technology as sustainable membrane technology in wastewater treatment.

Computational Approaches to Alkaline Anion-Exchange Membranes for Fuel Cell Applications

Anion-exchange membranes (AEMs) are key components in relatively novel technologies such as alkaline exchange-based membrane fuel cells and AEM-based water electrolyzers. The application of AEMs in these processes is made possible in an alkaline environment, where hydroxide ions (OH^-) play the role of charge carriers in the presence of an electrocatalyst and an AEM acts as an electrical insulator blocking the transport of electrons, thereby preventing circuit break. Thus, a good AEM would allow the selective transport of OH^- while preventing fuel (e.g., hydrogen, alcohol) crossover. These issues are the subjects of in-depth studies of AEMs-both experimental and theoretical studies-with particular emphasis on the ionic conductivity, ion exchange capacity, fuel crossover, durability, stability, and cell performance properties of AEMs. In this review article, the computational approaches used to investigate the properties of AEMs are discussed. The different modeling length scales are microscopic, mesoscopic, and macroscopic. The microscopic scale entails the ab initio and quantum mechanical modeling of alkaline AEMs. The mesoscopic scale entails using molecular dynamics simulations and other techniques to assess the alkaline electrolyte diffusion in AEMs, OH^- transport and chemical degradation in AEMs, ion exchange capacity of an AEM, as well as morphological microstructures. This review shows that computational approaches can be used to investigate different properties of AEMs and sheds light on how the different computational domains can be deployed to investigate AEM properties.

New block poly(ether sulfone) based anion exchange membranes with rigid side-chains and high-density quaternary ammonium groups for fuel cell application

We report a series of novel poly(ether sulfone) based anion exchange membranes (AEMs) with relatively good stability due to their rigid side-chains and heterocyclic quaternary ammonium groups. The AEMs show appropriate performance in AEM fuel cells.