Novel extractant impregnated resin for preconcentration and determination of uranium from environmental samples

Synthesis and Application of a New Polymer with Imprinted Ions for the Preconcentration of Uranium in Natural Water Samples and Determination by Digital Imaging

This work proposes the synthesis of a new polymer with imprinted ions (IIP) for the pre-concentration of uranium in natural waters using digital imaging as a detection technique. The polymer was synthesized using 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP) for complex formation, ethylene glycol dimethacrylate (EGDMA) as a crosslinking reagent, methacrylic acid (AMA) as functional monomer, and 2,2'-azobisisobutyronitrile as a radical initiator. The IIP was characterized by Fourier transform infrared spectroscopy and scanning electron microscopy (FTIR). Uranium determination was performed using digital imaging (ID), and some experimental conditions (sample pH, eluent concentration, and sampling flow rate) were optimized using a two-level full factorial design and Doelhert response surface methodology. Thus, using the optimized conditions, the system allowed the determination of uranium with detection and quantification limits of 2.55 and 8.51 µg L^-1, respectively, and a pre-concentration factor of 8.2. All parameters were determined using a 25 mL sample volume. The precision expressed as relative deviation (RSD%) was 3.5% for a solution with a concentration of 50 µg L^-1. Given this, the proposed method was used for the determination of uranium in four samples of natural waters collected in the city of Caetité, Bahia, Brazil. The concentrations obtained ranged from 35 to 75.4 μg L^-1. The accuracy was evaluated by the addition/recovery test, and the values found ranged between 91 and 109%.

Rhodamine-B dye removal using aliquat-336 modified amberlite XAD-4 resin in fixed-bed columns in series

The present work reports studies on the effective removal of Rhodamine-B (RhB) using Aliquat-336 modified Amberlite XAD-4 resin in the fixed-bed columns in series. The effect of flow rate (Q = 2 to 6 mL·min^-1), bed height (h = 3.5 to 7 cm) and initial RhB dye concentration (C_in = 10 to 20 mg·L^-1) was studied. When a single column was used, 93% RhB dye was removed in 3 h at Q = 2 mL·min^-1, C_in = 10 mg·L^-1, and h = 7 cm. When three columns in series were used, almost 100% dye was removed until 80 h. The maximum breakthrough time (142 h) and saturation time (244 h) were found by keeping Q = 2 mL·min^-1, h = 7 cm of each column and C_in = 10 mg·L^-1. Mathematical modeling of the breakthrough curves was done by using Yoon-Nelson, Clark, Wolborska, and pore diffusion models. The Clark model best fitted the experimental data. The possible interaction mechanism between Aliquat-336 and RhB dye was proposed. The column was regenerated in continuous mode using 1 M HCl solution and maintaining a flow rate of 2 mL·min^-1.

An anion exchange pretreatment method for the determination of low-level uranium in the environmental water samples

Uranium in environmental water is usually at trace or ultra-trace levels with high concentrations of background ions so that the detection of uranium often couples with pretreatment processes to lower the detection limit, and improve the selectivity and accuracy of instruments. A simple, green, effective and efficient anion exchange pretreatment method was proposed to favor the determination of low-level uranium in natural environmental water samples. To determine the applicability and obtain the optimum operating parameters, the effects of coprecipitation, pH, contact time, uranium concentration, background ions, eluent and the flow speed on the uranium recovery were investigated. The experimental results showed that the proper addition of saturated Na₂CO₃ solution for pH adjustment did not lead to uranium loss in natural water samples, and the optimum pH value for adsorption was determined from 6 to 8. The adsorption speed was improved a lot with the employment of a novel silica-supported anion exchange resin, which also showed good linear dependence in the concentration range from <0.5 μg/L to 1000 μg/L with high tolerance limits towards common background ions. The optimum eluent was determined as 1 M HNO₃, and the optimum flow speeds for adsorption and desorption were about 4.0 and 1.0 mL/min, respectively. Based on these results, a pretreatment process was finally established, which realized the quantitative recovery of uranium from six different natural water samples with the chemical yields exceeding 95% and the enrichment factors about 100 times.

Solvent impregnated resins for the treatment of aqueous solutions containing different compounds: a review

In this review paper, a complete study and analysis of the research articles dealing with the removal of various organic and inorganic pollutants using solvent impregnated resins (SIR) is carried out. The method of impregnation, characterizations of prepared resin, and regeneration techniques of different SIRs for batch and continuous fixed bed columns are presented. The effects of different operating parameters (e.g., loading of solvent on the resin, dosage of adsorbent, initial solute concentration, pH, temperature, time, ionic strength) on the separation efficiency of SIR in the batch mode are discussed. Thermodynamic parameters (change in Gibbs free energy, enthalpy, and entropy) are tabulated from the data available in the literature, and if not given, then their values are calculated and presented. The influence of parameters (flow rate, bed height, pH, concentration of the solution, etc.) on the fixed bed column performance is analyzed. Design aspects of the column are also discussed, and the dimensions of fixed bed columns for industrial applications are proposed.

Column and batch sorption investigations of nickel(II) on extractant-impregnated resin

Macroporous resin-supported reagents have been identified as potential adsorbents for removal of toxic pollutants. This article presents an experimental designed to evaluate the sorption and desorption of nickel(II) with the help of column and batch procedure using simple extractant-impregnated resin (EIR). Isonitroso-4-methyl-2-pentanone (IMP) as an extractant was impregnated on a solid support like Amberlite XAD-4 to prepare the EIR sorbent. Column experimental conditions such as pH, sample flow rate and volume, eluting solution, and interfering ions were studied to optimize the nickel(II) sorption and recovery from aqueous media. The column results suggest that the quantitative nickel(II) sorption was observed at pH 5-6, and the quantitative recovery (≥ 95%) was achieved by using 1.0 M HNO₃. The high concentrations of cations and anions (except EDTA) present in the spiked binary and multi-element mixture solution show no interferences in both quantitative sorption and recovery of nickel(II), whereas the batch experiments were performed to evaluate nickel(II) sorption behavior using the linearized and non-linearized kinetic and isotherm models. By error function analysis, the Freundlich isotherm and the pseudo-first-order kinetic model were found to describe best the experimental data obtained over the studied concentration range and sorption time, respectively. The maximum sorption capacity of nickel(II) onto the EIR sorbent was found to be ~ 81 mg/g. The mean free energy (E = 10.1 kJ/mol) determined using Dubinin-Radushkevich isotherm suggests chemical nature of nickel(II) sorption on EIR. The novelty of the EIR adsorbent lies in its potential for separation and recovery of nickel(II) at trace level in water samples of different origin.