Highly sensitive and selective fluorescent sensor for tetrabromobisphenol-A in electronic waste samples using molecularly imprinted polymer coated quantum dots

A Highly Efficient Fluorescent Turn-Off Nanosensor for Quantitative Detection of Teicoplanin Antibiotic from Humans, Food, and Water Based on the Electron Transfer between Imprinted Quantum Dots and the Five-Membered Cyclic Boronate Esters

Teicoplanin has been banned in the veterinary field due to the drug resistance of antibiotics. However, teicoplanin residue from the antibiotic abuse of humans and animals poses a threat to people's health. Therefore, it is necessary to develop an efficient way for the highly accurate and reliable detection of teicoplanin from humans, food, and water. In this study, novel imprinted quantum dots of teicoplanin were prepared based on boronate affinity-based precisely controlled surface imprinting. The imprinting factor (IF) for teicoplanin was evaluated and reached a high value of 6.51. The results showed excellent sensitivity and selectivity towards teicoplanin. The relative fluorescence intensity was inversely proportional to the concentration of teicoplanin, in the range of 1.0-17 μM. And its limit of detection (LOD) was obtained as 0.714 μM. The fluorescence quenching process was mainly controlled by a static quenching mechanism via the non-radiative electron-transfer process between QDs and the five-membered cyclic boronate esters. The recoveries for the spiked urine, milk, and water samples ranged from 95.33 to 104.17%, 91.83 to 97.33, and 94.22 to 106.67%, respectively.

Preparation of a magnetic molecularly imprinted polymer on fibrous silica nanosphere via self-polycondensation for micro solid-phase extraction of chlorpyrifos

Throughout this research, a new magnetic molecularly imprinted polymer on fibrous silica nanosphere was prepared through self-polycondensation. The selective extraction of chlorpyrifos was performed by the synthesized sorbent and as a determination system, a gas chromatography-electron capture was applied. The formation of sorbent was confirmed through the use of Fourier transform infrared spectroscopy and field emission scanning electron microscopy techniques. The parameters affecting the extraction efficacy of the proposed method were scrutinized in an optimized way. The linear range and the detection limit of the studied method were 0.003-0.3 and 0.001 ng mL-1, respectively. The relative standard deviations were 4.1-5.2 and 5.6-7.6 % for intra- and inter-day (n = 3), respectively. To assess the performance of the proposed method, some water and fruit samples were analyzed and the extraction recoveries of 83-109 % were obtained. These results revealed the method's performance in the analysis of chlorpyrifos in real samples.

Molecularly Imprinted Polymer-Based Biomimetic Systems for Sensing Environmental Contaminants, Biomarkers, and Bioimaging Applications

Molecularly imprinted polymers (MIPs), a biomimetic artificial receptor system inspired by the human body's antibody-antigen reactions, have gained significant attraction in the area of sensor development applications, especially in the areas of medical, pharmaceutical, food quality control, and the environment. MIPs are found to enhance the sensitivity and specificity of typical optical and electrochemical sensors severalfold with their precise binding to the analytes of choice. In this review, different polymerization chemistries, strategies used in the synthesis of MIPs, and various factors influencing the imprinting parameters to achieve high-performing MIPs are explained in depth. This review also highlights the recent developments in the field, such as MIP-based nanocomposites through nanoscale imprinting, MIP-based thin layers through surface imprinting, and other latest advancements in the sensor field. Furthermore, the role of MIPs in enhancing the sensitivity and specificity of sensors, especially optical and electrochemical sensors, is elaborated. In the later part of the review, applications of MIP-based optical and electrochemical sensors for the detection of biomarkers, enzymes, bacteria, viruses, and various emerging micropollutants like pharmaceutical drugs, pesticides, and heavy metal ions are discussed in detail. Finally, MIP's role in bioimaging applications is elucidated with a critical assessment of the future research directions for MIP-based biomimetic systems.

Preparation of molecularly imprinted ratiometric fluorescence sensor for visual detection of tetrabromobisphenol A in water samples

A sensitive molecularly imprinted ratiometric fluorescence sensor was constructed for the first time to visually detect tetrabromobisphenol A (TBBPA). The blue fluorescent carbon quantum dots (CQDs) were coated with SiO₂ through the reverse microemulsion method to obtain a stable internal reference signal CQDs@SiO₂. The ratiometric fluorescence sensor was finally prepared using red fluorescent CdTe QDs as the response signal in the presence of CQDs@SiO₂. When the molecularly imprinted polymers were combined with TBBPA, the fluorescence of CdTe QDs (Ex = 365 nm, Em = 665 nm) was rapidly quenched, while that of CQDs (Ex = 365 nm, Em = 441 nm) remained stable, resulting in a noticeable fluorescence color change. Moreover, the fluorescence intensity ratio (I₆₆₅/I₄₄₁)₀/(I₆₆₅/I₄₄₁) of the sensor showed a linear response to TBBPA in the concentration range 0.1 to 10 μM with a low detection limit of 3.8 nM. The prepared sensor was successfully applied to detect TBBPA in water samples. The recoveries were in the range 98.2-103%, with relative standard deviations lower than 2.5%. Furthermore, a fluorescent test strip for visual monitoring of TBBPA was constructed to streamline the procedure. The excellent results demonstrate that the prepared test strip has a broad prospect for the offline detection of pollutants.

A Highly Selective and Sensitive Fluorescent Sensor Based on Molecularly Imprinted Polymer-Functionalized Mn-Doped ZnS Quantum Dots for Detection of Roxarsone in Feeds

Roxarsone (ROX) as an organoarsenic feed additive has been widely used in livestock breeding and poultry industry, but ROX can degrade into highly toxic inorganic arsenic species in natural environments to threaten to the environment and human health. Therefore, there is a considerable interest in developing convenient, selective and sensitive methods for the detection of ROX in livestock breeding and poultry industry. In this work, a fluorescent molecularly imprinted polymer (MIPs) probe based on amino-modified Mn-ZnS quantum dots (QDs) has been developed by sol-gel polymerization for specific recognition of ROX. The synthesized MIPs-coated Mn-ZnS QDs (MIPs@Mn-ZnS QDs) have highly selective recognition sites to ROX because there are multi-interactions among the template ROX, functional monomer phenyltrimethoxysilane and the amino-functionalized QDs such as the π-π conjugating effect, hydrogen bonds. Under the optimal conditions, an obvious fluorescence quenching was observed when ROX was added to the solution, and the quenching mechanism could be explained as the photo-induced electron transfer. The MIPs@Mn-ZnS QDs sensor exhibited sensitive response to ROX in the linear range from 3.75 × 10^-8 M to 6.25 × 10^-7 M (R² = 0.9985) and the limit of detection down to 4.34 nM. Moreover, the fluorescence probe has been applied to the quantitative detection of ROX in feed samples, and the recovery was in the range of 91.9% to 108.0%. The work demonstrated that the prepared MIPs@Mn-ZnS QDs probe has a good potential for rapid and sensitive determination of ROX in complicated samples.

Boronate affinity-based template-immobilization surface imprinted quantum dots as fluorescent nanosensors for selective and sensitive detection of myricetin

In order to prepare a kind of efficient fluorescence sensors for determination of cis-diol-containing flavonoids, novel imprinted quantum dots for myricetin (Myr) were prepared based on boronate affinity-based template-immobilization surface imprinting. The obtained boronate affinity-based surface imprinted silica (imprinted APBA-functionalized CdTe QDs) was used as recognition elements. The quantum dots were used as signal-transduction materials. Under the optimum conditions, according to fluorescence quenching of imprinted APBA-functionalized CdTe QDs by Myr, the imprinting factor (IF) for Myr was evaluated to be 7.88. The result indicated that the boronate affinity functionalized quantum dots coated with imprinted silica were successfully prepared. The prepared imprinted APBA-functionalized CdTe QDs exhibited good sensitivity and selectivity for Myr. The fluorescence intensity was inversely proportional to the concentration of Myr in the 0.30-40 μM concentration range. And its detection limit was obtained to be 0.08 μM. Using the fluorescence sensors, the detection of Myr in real samples was successfully carried out, and the concentration of Myr in green tea and apple juice samples was evaluated to be 2.26 mg/g and 0.73 mg/g, respectively. The recoveries for the spiked green tea and apple juice samples were 95.2-105.0% and 91.5-111.0%, respectively. This study also provides an efficient fluorescent detection method for cis-diol-containing flavonoids in real samples.

Molecularly Imprinted Polymers (MIPs) in Sensors for Environmental and Biomedical Applications: A Review

Molecular imprinted polymers are custom made materials with specific recognition sites for a target molecule. Their specificity and the variety of materials and physical shapes in which they can be fabricated make them ideal components for sensing platforms. Despite their excellent properties, MIP-based sensors have rarely left the academic laboratory environment. This work presents a comprehensive review of recent reports in the environmental and biomedical fields, with a focus on electrochemical and optical signaling mechanisms. The discussion aims to identify knowledge gaps that hinder the translation of MIP-based technology from research laboratories to commercialization.

Morphology-dependent sensing performance of CuO nanomaterials

The morphology of nanomaterials affects their properties and further their applications. Herein, CuO nanomaterials with different morphologies are synthesized, including CuO nanostrips, nanowires and microspheres. After their characterization by means of electron microscopy and X-ray powder diffraction, these CuO nanomaterials are further mixed with graphene nanoplates (GNP) to explore their performance towards electrochemical detection of glucose and tetrabromobisphenol A (TBBPA). Among three composites, the composite of CuO nanostrips and GNP exhibits the largest active surface area, the lowest charge transfer resistance, and the highest accumulation efficiency toward TBBPA. Meanwhile, this composite based non-enzymatic sensor shows superior performance for the glucose monitoring. Since these sensors for the monitoring of both glucose and TBBPA possesses long-term stability, high reproducibility, and wide linear ranges and low detection limits, this work provides a strategy to tune the sensing performance of nanomaterials by means of tailoring the morphologies of nanomaterials.

Molecularly imprinted fluoroprobes doped with Ag nanoparticles for highly selective detection of oxytetracycline in real samples

A molecularly imprinted polymer (MIP), which is synthesized by a nanomolding process around a template, has emerged as a promising analytical tool for environmental quality monitoring and food safety test. In this work, a fluoroprobe with Ag-doped MIP nanolayer (16 nm thickness) is successfully prepared for the highly selective detection of oxytetracycline (OTC) in real samples (i.e. Yangtze River water, swine urine). In the MIP nanolayer, two functional monomers (i.e. 4-(2-acrylamidoethylcarbamoyl)-3-fluorophenylboronic acid, methacrylic acid) synergistically constitute the specific recognition sites. Meanwhile, the doped Ag enhances the detection sensitivity (with a detection limit of 5.38 nM) and accelerates the detection rate (within 2.5 min) even in real samples. Therefore, the present study paves the way for the preparation of MIP-based fluoroprobes, showing great prospects in environmental quality and food safety tests.

Imprinted Fluorescent Cellulose Membranes for the On-Site Detection of Myoglobin in Biological Media

In this work, the conjugation of molecularly imprinted polymers (MIPs) to quantum dots (QDs) was successfully applied in the assembly of an imprinted cellulose membrane [hydroxy ethyl cellulose (HEC)/MIP@QDs] for the specific recognition of the cardiac biomarker myoglobin (Myo) as a sensitive, user-friendly, and portable system with the potential for point-of-care (POC) applications. The concept is to use the MIPs as biorecognition elements, previously prepared on the surface of semiconductor cadmium telluride QDs as detection particles. The fluorescent quenching of the membrane occurred with increasing concentrations of Myo, showing linearity in the interval range of 7.39-291.3 pg/mL in a1000-fold diluted human serum. The best membrane showed a linear response below the cutoff values for myocardial infarction (23 ng/mL), a limit of detection of 3.08 pg/mL, and an imprinting factor of 1.65. The incorporation of the biorecognition element MIPs on the cellulose substrate brings an approach toward a portable and user-friendly device in a sustainable manner. Overall, the imprinted membranes display good stability and selectivity toward Myo when compared with the nonimprinted membranes (HEC/NIP@QDs) and have the potential to be applied as a sensitive system for Myo detection in the presence of other proteins. Moreover, the conjugation of MIPs to QDs increases the sensitivity of the system for an optical label-free detection method, reaching concentration levels with clinical significance.

Indirect competitive-structured electrochemical immunosensor for tetrabromobisphenol A sensing using CTAB-MnO2 nanosheet hybrid as a label for signal amplification

Tetrabromobisphenol A (TBBPA) is a kind of brominated flame retardant that is usually added to products to reduce their flame retardancy. However, its extensive use has resulted in their residues being found in the environment, which is very harmful. Herein, an indirect competitive immunosensor has been established for TBBPA detection based on the signal amplification system. Pd nanospheres in situ reduced on the surface of MnO₂ nanosheet hybrid (MnO₂/Pd) was used as the label for the secondary antibody through the Pd-N bond, and gold-toluidine blue composite was loaded onto MWCNTs (MWCNTs/Au-TB), which functioned as the platform for the immunosensor. The spherical structure of Pd had abundant catalytic active sites, which enhanced the catalytic activity of MnO₂/Pd as the label, hence amplifying the signal response. Besides, MWCNTs/Au-TB improved electron transfer and produced a strong signaling pathway for immobilizing antigens through the Au-NH₂ bond, which can specifically recognize primary antibodies to improve sensitivity. The immunosensor had a linear concentration range of 0-81 ng/mL, a low detection limit of 0.17 ng/mL (S/N = 3), with good stability, selectivity, and reproducibility based on the above advantages. Additionally, the acceptable accuracy and recoveries (recoveries, 92-124%; CV, 3.3-8.8%) in the real water sample analysis indicated that this strategy is promising for emerging pollutant analysis.

Ion-Imprinted Polymer Modified with Carbon Quantum Dots as a Highly Sensitive Copper(II) Ion Probe

Fluorescence analysis technology and ion imprinting technology are combined to prepare a copper ion fluorescence sensor. Carbon quantum dots (CQDs), with a quantum yield of 79%, were synthesized by a hydrothermal process using citric acid as the carbon source. The prepared CQDs, acting as the fluorophore, were grafted onto the surface of an SBA-15 mesoporous molecular sieve by an amidation reaction. Then, the fluorescent sensor CQDs@Cu-IIP was prepared using a surface imprinting technique with the modified SBA-15 as the substrate, copper ions as a template, tetraethoxysilane as the crosslinker, and 3-aminopropyl-3-ethoxysilane as the functional monomers. The sensor showed strong fluorescence from CQDs and high selectivity due to the presence of Cu(II)-IIP. After the detection conditions were optimized, the fluorescence intensity of the sensor had good linearity with Cu(II) concentration in a linear range of 0.25-2 mg/L and 3-10 mg/L. This CQDs@Cu-IIP was applied to the determination of traces Cu(II) in real water samples and good recoveries of 99.29-105.42% were obtained. The present study provides a general strategy for fabricating materials based on CQDs for selective fluorescence detection of heavy metals.

Molecularly imprinted polymer-capped wrinkled silica-quantum dot hybrid particles for fluorescent determination of tetra bromo bisphenol A

A fluorescent probe has been developed for tetra bromo bisphenol A (TBBPA) detection based on molecularly imprinted polymers (MIPs) combined with wrinkled silica nanoparticles (WSNs) and CdTe quantum dot (QD) hybrid particles. The WSNs with large pore sizes were employed as a structural support platform for QD embedding, and MIPs were synthesized on the surface of QD-embedded WSNs. The synthetic procedure was characterized using transmission electron microscopy, Brunauer-Emmett-Teller measurements, X-ray photoelectron spectrometry, Fourier transform infrared spectroscopy, and zeta potential analysis. The MIP-capped wrinkled silica-QD hybrid particles (WSNs-QDs-MIPs) possessed an adsorption capacity of 96.5 mg g^-1 with an imprinting factor of 7.9 towards TBBPA. Under the optimum incubation conditions, the fluorescence intensity (λ_ex = 340 nm, λ_em = 605 nm) was quenched in proportion to added TBBPA in the range 0.025 to 5 μM with a limit of detection of 5.4 nM. The developed probe was successfully applied to the detection of TBBPA in plastic electronic waste samples and the results of this method agreed with those obtained using high-performance liquid chromatography. This method presented a satisfactory selectivity, stability, and reproducibility indicating its potential as a promising probe for TBBPA detection.

Nanohybrid magnetic composite optosensing probes for the enrichment and ultra-trace detection of mafenide and sulfisoxazole

Nanohybrid magnetic optosensing probes were designed and fabricated to enrich and detect ultra-trace levels of mafenide and sulfisoxazole simultaneously. The probes combined the high affinity of MIL-101 and the sensitivity of graphene quantum dots (GQDs) and cadmium telluride quantum dots (CdTe QDs) with the selectivity and rapid separation provided by a magnetic molecularly imprinted polymer (MMIP). Since the MIL101-MMIP-GQD and MIL101-MMIP-CdTe QD probes produced high fluorescence emission intensities at 435 and 572 nm, respectively, mafenide and sulfisoxazole could be simultaneously detected. Quantitative analysis was based on fluorescence quenching produced by binding between target molecules and imprinted recognition cavities. In the optimal experimental condition, emission intensity was quenched linearly with increasing analyte concentration from 0.10 to 25.0 μg L^-1. Limit of detection was 0.10 μg L^-1 for mafenide and sulfisoxazole. The developed optosensor was applied to detect ultra-trace amounts of mafenide and sulfisoxazole in bovine milk. Recoveries of mafenide and sulfisoxazole in spiked bovine milk ranged from 80.4 to 97.9% with RSDs <5% and the analysis results agreed well with HPLC analysis. The proposed probes provided excellent sensitivity, selectivity, ease and convenience of use.

Simultaneous fluorescence determination of bisphenol A and its halogenated analogs based on a molecularly imprinted paper-based analytical device and a segment detection strategy

Bisphenol A (BPA) and its halogenated analogs tetrabromobisphenol A (TBBPA) and tetrachlorobisphenol A (TCBPA) are common environmental contaminants and a method for their simultaneous determination is urgently needed. A paper-based analytical device (PAD) was prepared using a metal-organic framework of UiO-66-NH₂ coated with molecularly imprinted polymers (MIPs) using TBBPA as a template. The maximum adsorption capacity was 120.94 mg g^-1 and the imprinting factor was 4.07. The selective recognition ability of this PAD enabled the effective separation of TBBPA, TCBPA and BPA based on paper chromatography. Subsequently, the PAD cut into segments were used individually to determine the presence of target chemicals using a highly sensitive fluorescent method. Under ultraviolet light irradiation, UiO-66-NH₂ acts as a photocatalyst to produce reactive oxygen species (ROS) that degrade TBBPA, TCBPA or BPA in the imprinted cavities and the fluorescent signal of 2',7'-dichlorodihydrofluorescein diacetate (H₂DCFDA) added as a ROS probe enabled the indirect determination of target chemicals. This method could determine BPA and its halogenated analogs in dust samples simultaneously with detection limits ranging from 0.14 to 0.30 ng g^-1. The intraday relative standard deviation (RSD) was ≤6.8% and interday RSD was ≤8.1%. The recoveries ranged from 91.0 to 105.6% with RSD values that were ≤7.5%. The results stemmed from this method were consistent with those obtained from LC-MS/MS. It is an environmentally-friendly approach due to the degradation of target pollutants and possesses many advantages such as high selectivity, low cost and easy-to-fabrication.

MIPs for commercial application in low-cost sensors and assays - An overview of the current status quo

Molecularly imprinted polymers (MIPs) have emerged over the past few decades as interesting synthetic alternatives due to their long-term chemical and physical stability and low-cost synthesis procedure. They have been integrated into many sensing platforms and assay formats for the detection of various targets, ranging from small molecules to macromolecular entities such as pathogens and whole cells. Despite the advantages MIPs have over natural receptors in terms of commercialization, the striking success stories of biosensor applications such as the glucose meter or the self-test for pregnancy have not been matched by MIP-based sensor or detection kits yet. In this review, we zoom in on the commercial potential of MIP technology and aim to summarize the latest developments in their commercialization and integration into sensors and assays with high commercial potential. We will also analyze which bottlenecks are inflicting with commercialization and how recent advances in commercial MIP synthesis could overcome these obstacles in order for MIPs to truly achieve their commercial potential in the near future.

Advances in Biomimetic Systems for Molecular Recognition and Biosensing

Understanding the fundamentals of natural design, structure, and function has pushed the limits of current knowledge and has enabled us to transfer knowledge from the bench to the market as a product. In particular, biomimicry―one of the crucial strategies in this respect―has allowed researchers to tackle major challenges in the disciplines of engineering, biology, physics, materials science, and medicine. It has an enormous impact on these fields with pivotal applications, which are not limited to the applications of biocompatible tooth implants, programmable drug delivery systems, biocompatible tissue scaffolds, organ-on-a-chip systems, wearable platforms, molecularly imprinted polymers (MIPs), and smart biosensors. Among them, MIPs provide a versatile strategy to imitate the procedure of molecular recognition precisely, creating structural fingerprint replicas of molecules for biorecognition studies. Owing to their affordability, easy-to-fabricate/use features, stability, specificity, and multiplexing capabilities, host-guest recognition systems have largely benefitted from the MIP strategy. This review article is structured with four major points: (i) determining the requirement of biomimetic systems and denoting multiple examples in this manner; (ii) introducing the molecular imprinting method and reviewing recent literature to elaborate the power and impact of MIPs on a variety of scientific and industrial fields; (iii) exemplifying the MIP-integrated systems, i.e., chromatographic systems, lab-on-a-chip systems, and sensor systems; and (iv) closing remarks.

Development and application of fluorescence sensor and test strip based on molecularly imprinted quantum dots for the selective and sensitive detection of propanil in fish and seawater samples

Molecularly imprinted quantum dots (MIP-QDs) were successfully synthesized via reversed-phase microemulsion and used as the specific recognition element and signal probe of a fluorescence sensor or test strip to achieve the highly sensitive detection of propanil. The physical-chemical characteristics and excellent selectivity of MIP-QDs were elucidated. Under optimized parameters, the MIP-QDs had good linearity at the propanil concentration range of 1.0 μg/L to 20.0 × 10³ μg/L by fluorescence quenching. The developed MIP-QD-based fluorescence sensor showed good recoveries ranging from 87.2 % to 112.2 %, and the relative standard deviation was below 6.0 % for the fish and seawater samples. In addition, the limits of detection (LODs) for fish and seawater were 0.42 μg/kg and 0.38 μg/L, respectively. The fluorescence test strip developed on the basis of the MIP-QDs also displayed satisfactory recoveries of 90.1 %-111.1 %, and the LOD for propanil in the seawater sample was 0.6 μg/L. The proposed fluorescence sensor and test strip were successfully used in propanil determination in environment and aquatic products.

Molecularly imprinted polymer containing fluorescent graphene quantum dots as a new fluorescent nanosensor for detection of methamphetamine

A novel fluorescent nanosensor based on graphene quantum dots embedded within molecularly imprinted polymer (GQDs@MIP) was developed for detection and determination of methamphetamine (METH). The resulting GQDs@MIP nanocomposite exhibited higher methamphetamine selectivity in comparison with corresponding non-imprinted polymer (GQDs@NIP). Characterization of the GQDs@MIP nanocomposite was done by nitrogen adsorption and desorption analysis (BET method), transmission electron microscopy (TEM), photoluminescence (PL), ultraviolet-visible (UV-Vis), and Fourier transform infrared (FT-IR) spectroscopies. The fluorescence intensity of GQDs@MIP was efficiently quenched in the presence of methamphetamine template molecules while no quenching was observed in the presence of other analytes such as amphetamine, ibuprofen, codeine, and morphine. Using this method, the detection limit of 1.7 μg/L was obtained for methamphetamine determination.

Determination of cis-diol-containing flavonoids in real samples using boronate affinity quantum dots coated with imprinted silica based on controllable oriented surface imprinting approach

Novel boronate affinity imprinted quantum dots (BA-CdTe@MIPs QDs) were used to develop a selective and sensitive fluorescent nanosensor for determination of cis-diol-containing flavonoids such as quercetin (Qu), baicalein (Bai) and luteolin (Lut) based on controllable oriented surface imprinting approach. The boronate affinity imprinted silica was used as recognition elements. Under the optimum conditions, the imprinting factor (IF) for Qu, Bai and Lut was evaluated to be 9.42, 6.58 and 10.91, respectively. The results indicated that the boronate affinity quantum dots coated with imprinted silica were successfully prepared. The obtained BA-CdTe@MIPs QDs provided high selectivity and high sensitivity for cis-diol-containing flavonoids such as quercetin and luteolin. The BA-CdTe@MIPs QDs exhibited linear decrease in fluorescence intensity with the increase of concentration of quercetin in the 0.05-25 μM concentration range. The detection limit (LOD) is evaluated to be 0.02 μM. The obtained fluorescent nanosensor could be successfully applied to efficient detection of cis-diol-containing flavonoids in onion skin and human urine samples. The recoveries for the spiked onion skin and urine samples were evaluated to be 83.50-104.00% and 86.67-105.00%, respectively. Clearly, this study provides a rapid and efficient fluorescent detection tool for cis-diol-containing flavonoids in real samples.

Ammoniated MOF-74(Zn) derivatives as luminescent sensor for highly selective detection of tetrabromobisphenol A

In this study, a porous framework MOF-74(Zn) (Zn₂ (DHBDC)(DMF)(H₂O)₂, H₄dondc = 1, 5-dioxido-2, 6-naphthalenedicarboxylic acid) with open metal sites was successful synthesized. MOF-74(Zn) as a template was grafted on the open metal sites with ethylenediamine (en) named MOF-74(Zn)-en to develop a highly selective and sensitive fluorescence detector for rapid determination of tetrabromobisphenol A (TBBPA). The obtained MOF-74(Zn)-en was well characterized by Fourier Transform Infrared (FT-IR), Scanning Electron Microscopy (SEM) and showed ideal properties of photoluminescence. The fluorescence enhancement showed a good linear relationship with the concentrations of TBBPA in the range of 50-400 μg/L, and its limit of detection could reach to 0.75 μg/L. Furthermore, the possible sensing mechanism of the fluorescence enhancement could be attributed to Förster resonance energy transfer (FRET). The results will provide a convenient and quick method for detection of TBBPA. To the best of my knowledge, this is the first case to detect TBBPA by fluorescence enhancement with MOF derivatives.

Molecularly Imprinted Polymer-Based Hybrid Materials for the Development of Optical Sensors

We report on the development of new optical sensors using molecularly imprinted polymers (MIPs) combined with different materials and explore the novel strategies followed in order to overcome some of the limitations found during the last decade in terms of performance. This review pretends to offer a general overview, mainly focused on the last 3 years, on how the new fabrication procedures enable the synthesis of hybrid materials enhancing not only the recognition ability of the polymer but the optical signal. Introduction describes MIPs as biomimetic recognition elements, their properties and applications, emphasizing on each step of the fabrication/recognition procedure. The state of the art is presented and the change in the publication trend between electrochemical and optical sensor devices is thoroughly discussed according to the new fabrication and micro/nano-structuring techniques paving the way for a new generation of MIP-based optical sensors. We want to offer the reader a different perspective based on the materials science in contrast to other overviews. Different substrates for anchoring MIPs are considered and distributed in different sections according to the dimensionality and the nature of the composite, highlighting the synergetic effect obtained as a result of merging both materials to achieve the final goal.

Preparation of Fluorescent Molecularly Imprinted Polymers via Pickering Emulsion Interfaces and the Application for Visual Sensing Analysis of Listeria Monocytogenes

In this work, a novel molecularly imprinted polymer (MIP) with water-soluble CdTe quantum dots (QDs) was synthesized by oil-in-water Pickering emulsion polymerization using whole Listeria monocytogenes as the template. Listeria monocytogenes was first treated by acryloyl-functionalized chitosan with QDs to form a bacteria-chitosan network as the water phase. This was then stabilized in an oil-in-water emulsion comprising a cross-linker, monomer, and initiator, causing recognition sites on the surface of microspheres embedded with CdTe QDs. The resulting MIP microspheres enabled selective capture of the target bacteria via recognition cavities. The target bacteria Listeria monocytogenes was detected. Scanning electron microscopy (SEM) characterization showed that the MIPs had a rough spherical shape. There was visual fluorescence detection via quenching in the presence of the target molecule, which offered qualitative detection of Listeria monocytogenes in milk and pork samples. The developed method simplified the analysis process and did not require any sample pretreatment. In addition, the fluorescence sensor provided an effective, fast, and convenient method for Listeria monocytogenes detection in food samples.

A nanocomposite fluorescent probe of polyaniline, graphene oxide and quantum dots incorporated into highly selective polymer for lomefloxacin detection

A nanocomposite fluorescent probe based on fluorescence quenching was fabricated and utilized for the detection of lomefloxacin. The fabricated probe integrated the high sensitivity of quantum dots, the excellent selectivity of molecularly imprinted polymer and the high adsorption affinity of graphene oxide and polyaniline. The probe exhibited good sensitivity, high specificity, and rapidity for lomefloxacin monitoring. Fluorescence emission was reduced linearly by lomefloxacin from 0.10 to 50.0 μg L^-1 and the probe exhibited a low limit of detection of 0.07 μg L^-1. The nanooptosensor successfully detected lomefloxacin in milk, chicken meat and egg samples. Recoveries were obtained in the range of 81.5-99.6% and the RSDs were below 7%. The results of this method agreed well with results of HPLC but provided higher sensitivity. This easily fabricated nanocomposite probe could be developed into a highly sensitive and selective optosensor to detect other organic compounds in various complex samples.