ZnO/CNT-COOHs based solid-state ECL sensor for tetracycline detection in fishpond water

One-Dimensional Covalent Organic Framework with Improved Charge Transfer for Enhanced Electrochemiluminescence

We present a dimensional regulating charge transfer strategy to achieve an enhanced electrochemiluminescence (ECL) by constructing a one-dimensional pyrene-based covalent organic framework (1D-COF). The dual-chain-like edge architecture in 1D-COF facilitates the stabilization of aromatic backbones, the enhancement of electronic conjugations, and the decrease of energy loss. The 1D-COF generates enhanced anodic (92.5-fold) and cathodic (3.2-fold) signals with tripropylamine (TPrA) and K2S2O8 as the anodic and cathodic coreactants, respectively, compared with 2D-COF. The anodic and cathodic ECL efficiencies of 1D-COF are 2.08- and 3.08-fold higher than those of 2D-COF, respectively. According to density functional theory (DFT), the rotational barrier energy (ΔE) of 1D-COF enhances sharply with the increase of dihedral angle, suggesting that the architecture in 1D-COF restrains the intramolecular spin of aromatic chains, which facilitates the decrease of nonradiative transitions and the enhancement of ECL. Furthermore, 1D-COF can be used to construct an ECL biosensor for sensitive detection of dopamine.

Supersensitive detection of lincomycin with an ECL aptasensor based on the synergistic integration of gold-functionalized upconversion nanoparticles and thiolated 3,4,9,10-perylene tetracarboxylic acid

In this work, the supersensitive and selective determination of lincomycin (Lin) was achieved using a novel electroluminescent (ECL) aptasensor based on the synergistic integration of gold functionalized upconversion nanoparticles (UCNPs) and thiolated 3,4,9,10-perylene tetracarboxylic acid (PTCA). The integration of two luminophores of UCNPs and PTCA combined the merits of the cathodoluminescence stability of UCNPs and the high quantum yield of PTCA, which significantly promoted the ECL signal and analytical performance of the proposed sensor. The introduction of gold nanoparticles in UCNPs can not only improve the conductivity and ECL performance of UCNPs but also cause them to easily integrate with thiolated PTCA (t-PTCA) via an Au-S bond. The ECL signal of UCNPs@Au/t-PTCA/GCE was almost twice as strong as that of t-PTCA/GCE and tenfold higher than that of UCNPs@Au/GCE. Because of the non-conductive protein of the Lin aptamer, the ECL intensity of apt/UCNPs@Au/t-PTCA/GCE noticeably decreased. In the presence of Lin, the aptamer was pulled down from the sensing interface, resulting in the recovery of the ECL intensity of the sensor. Under optimal conditions, our proposed sensor can quantify the concentration of Lin in the range from 1.0 × 10-15 to 1.0 × 10-7 M with a low detection limit of 2.4 × 10-16 M (S/N = 3), exhibiting high sensitivity and specificity for the determination of Lin.

Ultrasensitive Ratiometric Electrochemiluminescence Sensor with an Efficient Antifouling and Antibacterial Interface of PSBMA@SiO2-MXene for Oxytetracycline Trace Detection in the Marine Environment

The sensitivity and accuracy of electrochemiluminescence (ECL) sensors for detecting small-molecule pollutants in environmental water are affected not only by nonspecific adsorption of proteins and other molecules but also by bacterial interference. Therefore, there is an urgent need to develop an ECL sensor with antifouling and antibacterial functions for water environment monitoring. Herein, a highly efficient antifouling sensing interface (PSBMA@SiO2-MXene) based on zwitterionic sulfobetaine methacrylate (SBMA) antifouling nanospheres (NPs) and two-dimensional MXene nanosheets was designed for the sensitive detection of oxytetracycline (OTC), an antibiotic small-molecule pollutant. Specifically, SBMA with good hydrophilicity and electrical neutrality was connected to SiO2 NPs, thus effectively reducing protein and bacterial adsorption and improving stability. Second, MXene with a high specific surface area was selected as the carrier to load more antifouling NPs, which greatly improves the antifouling performance. Meanwhile, the introduction of MXene also enhances the conductivity of the antifouling interface. In addition, a ratio-based sensing strategy was designed to further improve the detection accuracy and sensitivity of the sensor by utilizing Au@luminol as an internal standard factor. Based on antifouling and antibacterial interfaces, as well as internal standard and ratiometric sensing strategies, the detection range of the proposed sensor was 0.1 ng/mL to 100 μg/mL, with a detection limit of 0.023 ng/mL, achieving trace dynamic monitoring of antibiotics in complex aqueous media.

Preparation of an electrochemical sensor utilizing graphene-like biochar for the detection of tetracycline

Tetracycline (TC), which is ubiquitous in the aquatic environment, can cause ecological imbalance and adversely affect human health. Therefore, a quick, inexpensive, and easy method for the detection of TC in water systems is highly desirable. This study reports the development of a novel electrochemical sensor from waste peanut shell for the quick detection of TC in water. Raman and TEM lattice mapping analyses confirmed the successful preparation of graphene -like biochar from waste peanut shells (PSs) via hydrothermal and pyrolysis processes. An electrochemical sensor, PS@glassy carbon electrode (PS@GCE), was then developed by coating the prepared graphene-like biochar on the surface of a glass electrode to enhance its conductivity. The feasibility of using this sensor for the detection of TC in the aqueous system was investigated. The PS@GCE sensor exhibited excellent sensitivity with a low detection limit of 3.6 × 10--9 nM and a linear range of 10-10-102 μM. These results were attributed to the large specific surface area and high conductivity, of the PS biochar. The stability of the PS@GCE sensor was also investigated in the presence of TC (10-4 M) and interfering species (10-2 M) and recovery rates in the range of 86.4%-116.0% were achieved, thus indicating the absence of an interference range of range of 84.3%-98.2% with relative standard deviation lower than 6% were achieved upon the detection of TC in natural water samples using the designed sensor, thus confirming the superior repeatability of the PS@GCE sensor. Consequently, the designed electrode has a high potential for application in the detection of TC in natural aqueous systems.

Electrochemiluminescence resonance energy transfer between a Ru-ZnMOF self-enhanced luminophore and a double quencher ZnONF@PDA to detect NSE

The construction of advanced systems capable of accurately detecting neuron-specific enolase (NSE) is essential for rapidly diagnosing small-cell lung cancer. In this study, an electrochemiluminescence (ECL) resonance energy transfer immunosensor was proposed for the ultra-sensitive detection of NSE. The co-reactants C2O42- and Ru(bpy)32+ were integrated to form a self-enhanced ECL luminophore (Ru-ZnMOF) as the ECL donor. The abundant carboxyl functional groups of Ru-ZnMOF supported antibody 1 via an amidation reaction. Polydopamine-modified zinc dioxide nanoflowers, as ECL acceptors, inhibited Ru-ZnMOF ECL signaling. The linear range of NSE was 10 fg mL-1 to 100 ng mL-1 with a detection limit of 3.3 fg mL-1 (S/N = 3), which is suitably low for determining NSE in real samples.

Recent progress in assembly strategies of nanomaterials-based ultrasensitive electrochemiluminescence biosensors for food safety and disease diagnosis

The Electrochemiluminescence (ECL)-based biosensors have received considerable attention in food contaminants and disease diagnosis, due to their fascinating advantages such as low cost, fast analysis speed, wide linear range, high sensitivity, and excellent anti-interference ability. Meanwhile, with the vigorous development and improvement of nanotechnology, biosensor assembly strategies tend to diversify and be multifunctional. This review focuses on the representative ECL biosensors in food safety and disease diagnosis reported by our research group and other research groups based on nanomaterials assembly strategies in recent years. According to the different roles of nanomaterials played in the constitution of ECL biosensors, nanomaterials would be divided into the following two categories to be summarized: (1) Nanomaterials for signal amplification. (2) Nanomaterials as ECL emitters. Finally, this review prospects the perspectives on the future development direction of ECL biosensor in food safety and disease diagnosis.

A novel metal-organic frameworks composite-based label-free point-of-care quartz crystal microbalance aptasensing platform for tetracycline detection

A novel label-free point-of-care quartz crystal microbalance (QCM) aptasensing platform based on metal-organic frameworks (MOFs) and gold nanoparticles (AuNPs) was fabricated for tetracycline (TC) detection. MOFs (HKUST-1) and AuNPs were modified onto the sensing interface of QCM sensor to enhance the sensing performance of the QCM aptasensor. TC aptamer with sulfhydryl group was fixed through Au-S bond. The recognition performance of the aptasensor was predicted and verified by the computer simulation. At the optimal conditions, the frequency change of the sensor was adopted for quantitative detection of TC. The prepared QCM aptasensor exhibited a wide linear range from 1 × 10^-10 g mL^-1 to 1 × 10^-5 g mL^-1 with low limit of detection (0.8 × 10^-11 g mL^-1). High sensitivity, good selectivity, acceptable recoveries (87.6-91.4%) in real samples were obtained. For the first time, MOFs were utilized in the construction of QCM aptasensing platform, providing a promising application way of MOFs in the QCM sensing.

The development of a wash-free homogeneous immunoassay method for the detection of tetracycline in environmental samples

Antibiotic residues have become the major source of environmental pollutants. In order to monitor tetracycline (TC) in the environment, we have established a highly sensitive and wash-free homogeneous time-resolved immunoassay. This analytical method was based on a rare earth chelate with excellent fluorescence properties. The cryptate organic ligand had good stability and acted as an antenna for Eu3+ excitation. In a homogeneous system, the Eu3+ cryptate complex was used as a label to bind to antibodies. Under the action of immunoaffinity, fluorescent donors and acceptors were close to each other, which induced the FRET effect to produce proportional fluorescence. Under the optimal parameters, the half-inhibitory concentration (IC50) and limit of detection (LOD, IC10) of TC were 0.4188 ng mL-1 and 0.0106 ng mL-1, respectively. The linear range (IC20-IC80) was 0.0273-9.2645 ng mL-1. With the environmental samples, the recovery rate of TC was 84.3-107.2%, and the standard deviation (RSD) was 4.6-12.9%. The results showed the good sensitivity and reliability of the method. Compared with the traditional ELISA, our method has less background interference, only one step was required without the washing procedure, and the detection result can be obtained by 30 min incubation, which improves the detection efficiency. Because of the characteristics of immunoassays, different pollutants can be monitored by changing the antibodies. This method provides an alternative path for detecting environmental pollutants and has the potential to develop into an on-site detection kit.

Fluorometric Aptasensor for Determination of Escherichia coli O157:H7 by FRET Effect between Aminated Carbon Quantum Dots and Graphene Oxide

A fluorometric aptasensor based on Escherichia coli O157:H7 (E. coli O157:H7) aptamer labeled aminated carbon quantum dots (NH₂-CQDs) and graphene oxide (GO) for the determination of E. coli O157:H7 was developed. In this research, carboxyl group (-COOH) terminated E. coli O157:H7 aptamer was steadily labeled to NH₂-CQDs by amidation reaction, and played the role of energy donor and was responsible for chemical recognition. Correspondingly, GO served as an energy acceptor. The introduction of NH₂-CQDs not only made the aptamer bond stably through covalent bond, but also significantly enhanced the fluorescence intensity compared with general CQDs. The NH₂-CQDs-aptamer is adsorbed on the surface of GO through π-π stacking and hydrophobic interaction. The fluorescence of NH₂-CQDs-aptamer was quenched via fluorescence resonance energy transfer (FRET) between NH₂-CQDs and GO. After adding E. coli O157:H7, the specific binding affinity between NH₂-CQDs-aptamer and E. coli O157:H7 lead to desorption of NH₂-CQDs-aptamer from GO, and recovery of the fluorescence intensity of NH₂-CQDs-aptamer. Under the optimal conditions, the increased fluorescence intensity showed a good linear relationship to concentrations of E. coli O157:H7 in the range 10² - 10⁷ cells/mL, with a detection limit of 89 cells/mL. Furthermore, the developed method was successfully applied to the determination of E. coli O157:H7 in commercial milk samples.

Recent development of antibiotic detection in food and environment: the combination of sensors and nanomaterials

In recent years, the abuse of antibiotics has led to the pollution of soil and water environment, not only poultry husbandry and food manufacturing will be influenced to different degree, but also the human body will produce antibody. The detection of antibiotic content in production and life is imperative. In this review, we provide comprehensive information about chemical sensors and biosensors for antibiotic detection. We classify the currently reported antibiotic detection technologies into chromatography, mass spectrometry, capillary electrophoresis, optical detection, and electrochemistry, introduce some representative examples for each technology, and conclude the advantages and limitations. In particular, the optical and electrochemical methods based on nanomaterials are discussed and evaluated in detail. In addition, the latest research in the detection of antibiotics by photosensitive materials is discussed. Finally, we summarize the pros and cons of various antibiotic detection methods and present a discussion and outlook on the expansion of cross-scientific areas. The synthesis and application of optoelectronic nanomaterials and aptamer screening are discussed and prospected, and the future trends and potential impact of biosensors in antibiotic detection are outlined.Graphical abstract.

A Sensitive Fluorescent Assay for Tetracycline Detection Based on Triple-helix Aptamer Probe and Cyclodextrin Supramolecular Inclusion

Herein, an effective pyrene excimer signaled fluorescent biosensor for the determination of tetracycline based on triple-helix aptamer probe (TAP) and supramolecular inclusion of cyclodextrin was reported. The TAP was devised containing an aptamer loop, two DNA segment stems and a triplex-forming oligonucleotide (signal probe) labeled with pyrenes at 5' and 3' ends. The presence of target could result in its binding towards aptamer with a mighty affinity, leading to a conformation change of the TAP and whereupon the release of the signal probe. This liberty of signal probe enabled the formation of pyrene excimer, generating fluorescence signals. Further, signal amplification was fulfilled through the addition of γ-cyclodextrin which could interact with pyrene dimer, thus leading to an enhanced "on-state" of the sensing ensemble. In contrast, when the target was absent, the sensing ensemble remained "off-state" because of the long distance between two pyrene molecules. When the conditions were properly optimized, the increasing signal kept a linear dependence on target concentrations ranging from 5.0 nM to 100 nM, and the detection limit reached as low as 1.6 nM. In this way, a newly-constructed, simple, and economically affordable protocol enjoys desirable efficiency, sensitivity, specificity in biosensing. Also, its universality as another attractive behalf in assaying diverse targets was envisioned with only the need of matched aptamer replacement.