Indium-doped mesoporous Bi2S3-based electrochemical interface for highly sensitive detection of Pb(II)

Nano-palladium-decorated bismuth sulfide microspheres on a disposable electrode integrated with smartphone-based electrochemical detection of nitrite in food samples

Nitrite (NO2-) is widely used as an additive to extend the shelf life of food products. Excessive nitrite intake not only causes blood-related diseases but also has the potential risk of causing cancers. A disposable screen-printed electrode was modified with nano‑palladium decorated bismuth sulfide microspheres (nanoPd@Bi2S3MS/SPE), and integrated with a smartphone-interfaced potentiostat to develop a portable, electrochemical nitrite sensor. NanoPd@Bi2S3MS was prepared by the hydrothermal reduction of a Bi2S3MS and Pd2+ dispersion and drop cast on the SPE. The nanoPd@Bi2S3MS/SPE was coupled with a smartphone-controlled portable potentiostat and applied to determine nitrite in food samples. The linear range of the sensor was 0.01-500 μM and the limit of detection was 0.0033 μM. The proposed system showed good repeatability, reproducibility, catalytic stability, and immunity to interferences. The proposed electrode material and a smartphone-based small potentiostat created a simple, portable, fast electrochemical sensing system that accurately measured nitrite in food samples.

A portable magnetic electrochemical sensor for highly efficient Pb(II) detection based on bimetal composites from Fe-on-Co-MOF

The practical, sensitive, and real-time detection of heavy metal ions is an essential and difficult problem. This study presents the design of a unique magnetic electrochemical detection system that can achieve real-time field detection. To enhance the electrochemical performance of the sensor, Fe2O3@C-800, Co/CoO@/C-600, and CoFe2O4@C-600 magnetic composites were synthesized using three MOFs precursors by the solvothermal method. And the morphology structure and electrochemical properties of as-prepared magnetic composites were researched by X-ray diffraction (XRD), Scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS), vibrating sample magnetometer (VSM), specific surface area and porosity analyzer (BET) and differential pulse voltammetry (DPV). The results shown that these composites improve conductivity and stability while preserving the MOFs basic frame structure. Compared with the monometallic MOFs-derived composites, the synergistic effect of the bimetallic composite CoFe2O4@C-600 can significantly enhance the electrochemical performance of the sensor. The linear range for the detection of lead ions was 0.001-60 μM, and the detection limit was 0.0043 μM with a sensitivity of 22.22 μA μM·cm-2 by differential pulse voltammetry. The sensor has good selectivity, stability, reproducibility and can be used for actual sample testing.

Label-free electrochemical aptasensor for ultrasensitive lead ion detection based on flower-like AuNPs@MoS2 and core-shell Pt@Pd bimetallic nanoparticles

A signal-amplified platform was designed to construct a label-free electrochemical aptasensor for lead ions (Pb2+) assay. First, flower-like molybdenum disulfide-supported AuNPs (AuNPs@MoS2) nanocomposites were synthesized and used as substrates for modifying the electrode. The AuNPs@MoS2 material possessed large surface area and superior biocompatibility, which was beneficial to improve the loading amount of the complementary DNA (cDNA) and amplified the response signal. Importantly, the prepared core-shell Pt@Pd bimetallic nanoparticles (Pt@PdNPs) were used to conjugate with redox marker thionine (Thi) and aptamer (Apt) for further signal amplification; the obtained signal probes (Thi-Pt@PdNPs-Apt) were connected by the cDNA assembled on the electrode through DNA hybridization. Differential pulse voltammetry was performed to monitor the signal of Thi. After incubating of aptasensor with Pb2+, the specific recognition of Pb2+ and Apt resulted in the dissociation of aptamer-cDNA complex, thereby the Thi-Pt@PdNPs-Apt separated from the electrode surface and decreased current response was obtained. The prepared electrochemical sensor exhibited linear response to Pb2+ in the range 5.0 × 10-4-100 nM and a detection limit of 1.0 × 10-4 nM was achieved. The sensor was applied to the determination of Pb2+ in actual sample with high sensitivity and accuracy, demonstrating potential applications in heavy metal monitoring.

Bismuth sulfide micro flowers decorated nickel foam as a promising electrochemical sensor for quantitative analysis of melamine in bottled milk samples

Here, we demonstrate hydrothermally grown bismuth sulfide (Bi2S3) micro flowers decorated nickel foam (NF) for electrochemical detection of melamine in bottled milk samples. The orthorhombic phase of hydrothermally grown Bi2S3is confirmed by the detailed characterization of x-ray diffraction and its high surface area micro flowers-like morphology is investigated via field emission scanning electron microscope. Furthermore, the surface chemical oxidation state and binding energy of Bi2S3/NF micro flowers is analyzed by x-ray photoelectron spectroscopy studies. The sensor exhibits a wide linear range of detection from 10 ng l-1to 1 mg l-1and a superior sensitivity of 3.4 mA cm-2to melamine using differential pulse voltammetry technique, with a lower limit of detection (7.1 ng l-1). The as-fabricated sensor is highly selective against interfering species of p-phenylenediamine (PPDA), cyanuric acid (CA), aniline, ascorbic acid, glucose (Glu), and calcium ion (Ca2+). Real-time analysis done in milk by the standard addition method shows an excellent recovery percentage of ̴ 98%. The sensor's electrochemical mechanism studies reveal that the high surface area bismuth sulfide micro flowers surface interacts strongly with melamine molecules through hydrogen bonding and van der Waals forces, resulting in a significant change in the sensor's electrical properties while 3D skeletal Nickel foam as a substrate provides stability, enhances its catalytic activity by providing a more number /of active sites and facilitates rapid electron transfer. The work presented here confirms Bi2S3/NF as a high-performance electrode that can be used for the detection of other biomolecules used in clinical diagnosis and biomedical research.

Bipotential-resolved electrochemiluminescence biosensor based on Bi2S3@Au nanoflowers for simultaneous detection of Cd(II) and ampicillin in aquatic products

In this paper, an electrochemiluminescence (ECL) biosensor was constructed using Bi₂S₃@Au nanoflowers as the based nanomaterial and Au@luminol and CdS QDs as independent ECL emission signal respectively. As the substrate of the working electrode, Bi₂S₃@Au nanoflowers improved the effective area of electrode and accelerated electron transfer rate between gold nanoparticles and aptamer, provided a good interface environment for the loading of luminescent materials. Then, the Au@luminol functionalized DNA2 probe was used as an independent ECL signal source under positive potential and recognized Cd(II), while the CdS QDs functionalized DNA3 probe was used as an independent ECL signal source under negative potential and recognized ampicillin. The simultaneous detection of Cd(II) and ampicillin in different concentrations are realized. This sensor not only has good selectivity and high sensitivity in real sample detection, but also open up a novel way to construct multi-target ECL biosensor for simultaneous detection.

A Planar Disk Electrode Chip Based on MWCNT/CS/Pb2+ Ionophore IV Nanomaterial Membrane for Trace Level Pb2+ Detection

Unlike conventional lead ion (Pb2+) detecting methods, electrochemical methods have the attractive advantages of rapid response, good portability and high sensitivity. In this paper, a planar disk electrode modified by multiwalled carbon nanotube (MWCNTs)/chitosan (CS)/lead (Pb2+) ionophore IV nanomaterial and its matched system are proposed. This system presented a good linear relationship between the concentration of Pb2+ ions and the peak current in differential pulse stripping voltammetry (DPSV), under optimized conditions of -0.8 V deposition potential, 5.5 pH value, 240 s deposition time, performed sensitive detection of Pb2+ within sensitivity of 1.811 μA · μg^-1 and detection limit of 0.08 μg · L^-1. Meanwhile, the results of the system in detecting lead ions in real seawater samples are highly similar to that of inductively coupled plasma emission spectrometer (ICP-MS), which proved a practicability for the system in detection of trace-level Pb2+.

Sensitive and Selective Electrochemical Detection of Lead(II) Based on Waste-Biomass-Derived Carbon Quantum Dots@Zeolitic Imidazolate Framework-8

An electrochemical sensor based on carbon quantum dots (CQDs) and zeolitic imidazolate framework-8 (ZIF-8) composite was fabricated to detect lead(II). The CQDs (2.47 ± 0.52 nm) were synthesized from platanus acerifoli leaves by carbonization and the hydrothermal method. Under the optimal conditions, the fabricated electrochemical sensor had excellent performance in detecting Pb²⁺. The linear range for Pb²⁺ was 1 nM-1 μM, and the limit of detection (LOD) was 0.04 nM and the limit of quantification (LOQ) was 0.14 nM. Moreover, when the solution contained Pb²⁺ and Cd²⁺, the linear range for Pb²⁺ was 50 nM to 1 μM and the LOD was 0.02 nM. When the solution contained Pb²⁺ and Cu²⁺, the linear range for Pb²⁺ was 50 nM-750 nM and LOD was 0.07 nM. Furthermore, even if the solution contained Pb²⁺, Cd²⁺ and Cu²⁺, the linear range for Pb²⁺ was 50 nM-1 μM and the LOD was 0.04 nM. The X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrometer (FTIR) and Brunauer-Emmet-Teller (BET) results indicated that the composite electrode materials had abundant oxygen-containing functional groups, a large specific surface area and pore structure, which are conducive to the adsorption of heavy metal ions and improve the detection performance.

Electrochemical sensor based on Bi/Bi2O3 doped porous carbon composite derived from Bi-MOFs for Pb2+ sensitive detection

It is of great significance to develop electrochemical sensors based on novel functional nanomaterials for heavy metal ions detection. In this work, a novel Bi/Bi₂O₃ co-doped porous carbon composite (Bi/Bi₂O₃@C) was prepared by simple carbonization of bismuth-based metal-organic frameworks (Bi-MOFs). The micromorphology, internal structure, crystal and elemental composition, specific surface area and porous structure of the composite were characterized by SEM, TEM, XRD, XPS, and BET. Further, a sensitive electrochemical sensor for Pb²⁺ detection was constructed by modifying Bi/Bi₂O₃@C on the surface of the glassy carbon electrode (GCE) based on the square wave anodic stripping voltammetric (SWASV). The different factors affecting the analytical performance were optimized systematically, such as material modification concentration, deposition time, deposition potential, and pH value. Under optimized conditions, the proposed sensor exhibited a wide linear range from 37.5 nM to 2.0 μM with a low detection limit of 6.3 nM. Meanwhile, the proposed sensor showed good stability, acceptable reproducibility, and satisfactory selectivity. The reliability of the as-proposed sensor was confirmed by the ICP-MS method for Pb²⁺ detection in different samples.

Construction of a Carbon/Lignosulfonate Adsorbent to Remove Pb2+ and Cu2

Removing heavy metal ions from water is an important issue to improve water quality. However, using cost-effective and more environmentally friendly adsorbents to achieve efficient adsorption capacity remains a challenge. Carbon spheres were prepared by the hydrothermal method and then combined with sodium lignosulfonate to form a lignosulfonate carbon (C/SL) adsorbent. C/SL achieved the adsorption of Pb²⁺ and Cu²⁺ after 60 min (the adsorption capacity was 281 mg g^-1 for Pb²⁺ and 276mg g^-1 for Cu²⁺) and had good selectivity and reusability (5 cycles). The simulated experimental data show that the pseudo-second-order kinetics and Langmuir isotherm are closer to the actual adsorption. Thermodynamic studies show that the adsorption of Pb²⁺ and Cu²⁺ is enhanced by the spontaneous process at higher temperature. This study also shows that functional groups such as hydroxyl and amino groups play an important role in the adsorption process.

An "Off-On" Rhodamine 6G Hydrazide-Based Output Platform for Fluorescence and Visual Dual-Mode Detection of Lead(II)

In this study, the rhodamine 6G hydrazide (R6GH) complex was synthesized to develop an "off-on" output platform for fluorescence and visual dual-mode analysis of lead(II) (Pb2+). The prepared R6GH complex using the heat to reflux reaction of rhodamine 6G (R6G) and hydrazine hydrate was characterized through FT-IR, MS, 1H NMR, and 13C NMR and demonstrated to have good fluorescence stability and reversibility. The microenvironment for Pb2+ detection has been optimized in detail. Under the optimal conditions, the "off-on" R6GH-based fluorescence output platform showed a good response to Pb2+ in the concentration range of 0.05-6.0 μM (R2 = 0.9851) with a limit of detection (LOD) of 0.02 μM. Furthermore, at three spiked Pb2+ levels in the selected agricultural (tap water, soil) and food (fish, shrimp) samples, the developed R6GH-based fluorescence assays obtained a significant recovery range of 84.0-102.0% (RSD < 5.0%, n = 3), which had a good correlation with the results from ICP-MS (R2 = 0.9915). The developed R6GH immobilized paper-based array sensor can reach the lower LOD (2.5 μM) for Pb2+ through the naked eye. By combining with LAB analysis, a good linear response was obtained in the Pb2+ concentration range of 1.0-50.0 μM. These results indicated that the developed R6GH probe had great application potential in accurate detection of fluorescence and rapid visual and semiquantitative screening for Pb2+.