Influence of adsorbed polysaccharides and polyacrylamides on talc flotation

Increasing surface hydrophilicity with biopolymers: a combined single bubble collision, QCM-D and AFM study

HYPOTHESIS

Naturally extracted polysaccharides, such as guar gum, are promising candidates for environmentally friendly flotation reagents. It is hypothesized that the kinetics of collision of sub- to millimeter gas bubbles with a hydrophobic graphite surface, and the stability of thin liquid film formed between the bubble and surface is affected by an adsorbed layer of guar gum.

EXPERIMENTS

A combination of gravimetric (quartz crystal microbalance with dissipation) and imaging (atomic force microscopy) techniques was used to investigate the adsorption of guar gum on graphite surface, while high-speed camera imaging allowed for direct observation of the bubble collision process with guar gum-modified graphite surfaces with millisecond resolution.

FINDINGS

Atomic force microscope topography images revealed a guar gum concentration-dependent interconnected network of guar gum molecules adsorbed at graphite surface. These adsorbed molecules at low surface coverage, changed the wettability of the graphite surface, resulting in a film drainage time longer by an order of magnitude, while at higher surface coverage successfully prevented bubble attachment to the graphite surface. Most importantly, the adsorbed layer changed the strength of the bubble's bouncing off the graphite surface. This enhanced bubble bouncing can be correlated with the film drainage time and used to predict a successful bubble-particle attachment.

The pH dependent surface charging and points of zero charge. X. Update

Surfaces are often characterized by their points of zero charge (PZC) and isoelectric points (IEP). Different authors use these terms for different quantities, which may be equal to the actual PZC under certain conditions. Several popular methods lead to results which are inappropriately termed PZC. This present review is limited to zero-points obtained in the presence of inert electrolytes (halides, nitrates, and perchlorates of the 1st group metals). IEP are reported for all kinds of materials. PZC of metal oxides obtained as common intersection points of potentiometric curves for 3 or more ionic strengths (or by means of equivalent methods) are also reported, while the apparent PZC obtained by mass titration, pH-drift method, etc. are deliberately neglected. The results published in the recent publications and older results overlooked in the previous compilations by the same author are reported. The PZC/IEP are accompanied by information on the temperature and on the nature and concentration of supporting electrolyte (if available). The references to previous reviews by the same author allow to compare the newest results with the PZC/IEP of similar materials from the older literature.

A review of effects and applications of ultrasound in mineral flotation

Ultrasound technology is widely applied in the flotation process. From the perspective of the theory of ultrasound, this article explains the effects and applications of ultrasound in the flotation process. To obtain a clear understanding of ultrasonic effects, we observe the phenomena of ultrasound using a high-speed camera and a CCD camera, and investigate potential applications in flotation. From these different phenomena, the ultrasonic effects are classified into three types of effect: the transient cavitation effect, stable cavitation effect, and acoustic radiation force effect. Based on these effects, the applications of ultrasound to mineral flotation are reviewed, including slime coating removal, oxidation film removal, desulfuration, tiny bubble generation, flotation reagent dispersion, and aggregation. In addition, the ultrasonic equipment and treatment methods applied in flotation are classified and compared based on their characteristics. Finally, we propose some potential directions in the study of the stable cavitation effect and acoustic radiation force effect, which are important, but are seldom mentioned in previous reports.

Effects of Xanthate on Flotation Kinetics of Chalcopyrite and Talc

This paper investigated the effects of using or not using potassium butyl xanthate (PBX) as a collector on the flotation kinetics of talc and chalcopyrite. By means of atomic force microscopy (AFM), Fourier-transform infrared spectroscopy (FTIR), a contact angle measuring instrument and particle size analyzer, the underlying causes behind the flotation rate changes of talc and chalcopyrite are analyzed. Experimental results showed that in collectorless flotation, the law of change in the flotation rate constant (k) of the two minerals over time is independent of pH, and k values of chalcopyrite are much smaller than those of talc. In the presence of PBX, the flotation speed of chalcopyrite greatly increases, and the k values of chalcopyrite are far larger than those of talc. This is mainly because the amount of xanthate adsorbed on the surface of chalcopyrite is large and the adsorption is in the form of chemisorption, while the adsorption of xanthate on the talcum surface is in very small amounts and in the form of physical adsorption. Simulation results indicated that the collectorless flotation of chalcopyrite conform to the classical first-order kinetics model and the Kelsall model, whereas that of talc only conform to the latter, which is due to the layered structure of talc. In the presence of the collector, talc flotation conforms to the two model, because talc has a higher floatability and particle morphology has less influence on the flotation rate.

In situ particle film ATR FTIR spectroscopy of poly (N-isopropyl acrylamide) (PNIPAM) adsorption onto talc

The adsorption of poly(N-isopropyl acrylamide) (PNIPAM) onto talc from aqueous solutions has been studied using the in situ methodology of particle film attenuated total reflection (ATR) Fourier transform infrared (FTIR) spectroscopy. PNIPAM was observed to adsorb significantly onto the talc particle film at a temperature below its lower critical solution temperature (LCST). Peak shifts were seen in the adsorbed layer FTIR spectrum that match those observed when PNIPAM solution is heated above its LCST. This observation indicates that adsorption causes a conformational re-arrangement similar to that seen when PNIPAM undergoes a coil-to-globule transition, in this case presumably induced by hydrophobic interactions between PNIPAM and the talc basal plane surface. The kinetics of adsorption are seen to be complex, with potential influences of conformational rearrangement and differential adsorption kinetics for the two dominant surface regions of talc particles. The adsorbed PNIPAM was seen to be exceptionally resistant to removal, with no desorption occurring when a background electrolyte solution was flowed over the adsorbed layer. Spectra acquired of the adsorbed polymer layer heated above the LCST reveal that a further conformational rearrangement takes place for the adsorbed layer, finalizing the transition from coil-to-globule that was initiated by the interaction with the mineral surface.

Carboxymethylcellulose adsorption on molybdenite: the effect of electrolyte composition on adsorption, bubble-surface collisions, and flotation

The adsorption of carboxymethylcellulose polymers on molybdenite was studied using spectroscopic ellipsometry and atomic force microscopy imaging with two polymers of differing degrees of carboxyl group substitution and at three different electrolyte conditions: 1 × 10(-2) M KCl, 2.76 × 10(-2) M KCl, and simulated flotation process water of multicomponent electrolyte content, with an ionic strength close to 2.76 × 10(-2) M. A higher degree of carboxyl substitution in the adsorbing polymer resulted in adsorbed layers that were thinner and with more patchy coverage; increasing the ionic strength of the electrolyte resulted in increased polymer layer thickness and coverage. The use of simulated process water resulted in the largest layer thickness and coverage for both polymers. The effect of the adsorbed polymer layer on bubble-particle attachment was studied with single bubble-surface collision experiments recorded with high-speed video capture and image processing and also with single mineral molybdenite flotation tests. The carboxymethylcellulose polymer with a lower degree of substitution resulted in almost complete prevention of wetting film rupture at the molybdenite surface under all electrolyte conditions. The polymer with a higher degree of substitution prevented rupture only when adsorbed from simulated process water. Molecular kinetic theory was used to quantify the effect of the polymer on the dewetting dynamics for collisions that resulted in wetting film rupture. Flotation experiments confirmed that adsorbed polymer layer properties, through their effect on the dynamics of bubble-particle attachment, are critical to predicting the effectiveness of polymers used to prevent mineral recovery in flotation.

In situ ATR FTIR study of dextrin adsorption on anatase TiO2

The adsorption of two dextrin-based polymers, a regular wheat dextrin (TY) and a carboxymethyl-substituted (CM) dextrin, onto an anatase TiO(2) particle film has been studied using in situ attenuated total reflection (ATR) FTIR spectroscopy. Infrared spectra of the polymer solutions and the polymer adsorbed at the anatase surface were acquired for two solution conditions: pH 3 and pH 9; below and above the isoelectric point (IEP) of anatase, respectively. Comparison of the polymer solution spectra and the adsorbed layer spectra highlighted a number of spectral differences that were attributed to involvement of the carboxyl group of CM Dextrin interacting with the anatase surface directly and the adsorption of oxidized dextrin chains in the case of regular dextrin (TY) at high pH. The adsorption/desorption kinetics were determined by monitoring spectral peaks of the pyranose ring of both polymers. Adsorption equilibrium was not established for Dextrin TY for many hours, whereas CM Dextrin reached equilibrium in its adsorption within 60 min. The extent of desorption of Dextrin TY (observed by flowing a background electrolyte dextrin-free solution) was extensive at both pH values, which reflects the poor affinity and binding of the polymer on anatase. In contrast, CM Dextrin underwent almost no desorption, indicating a high affinity between the carboxyl groups of the polymer and the anatase surface.

Isotherm and kinetic behavior of adsorption of anion polyacrylamide (APAM) from aqueous solution using two kinds of PVDF UF membranes

To determine the isotherm parameters and kinetic parameters of adsorption of anion polyacrylamide (APAM) from aqueous solution on PVDF ultrafiltration membrane (PM) and modified PVDF ultrafiltration membrane (MPM) is important in understanding the adsorption mechanism of ultrafiltration processes. Effect of variables including adsorption time, initial solution concentration, and temperature were investigated. The Redlich-Peterson equation of the five different isotherm models we chose was the most fitted model, and the R(2) was 0.9487, 0.9765 for PM and MPM, respectively; while, the pseudo-first-order model was the best choice among all the four kinetic models to describe the adsorption behavior of APAM onto membranes, suggesting that the adsorption mechanism was a chemical and physical combined adsorption on heterogeneous surface. The thermodynamic parameters were also calculated from the temperature dependence (Δ(r)G(m)(θ), Δ(r)H(m)(θ), Δ(r)S(m)(θ)), which showed that the process of adsorption is not spontaneous but endothermic process and high temperature favors the adsorption.

Effect of adsorbed polymers on bubble--particle attachment

The influence of adsorbed dextrin-based polymers on the attachment of a rising air bubble to a talc surface has been investigated. Liquid film rupture and dynamic contact angle studies have highlighted the major role that adsorbed polymers can play in bubble-particle attachment. No direct link was established between the equilibrium contact angle of polymer-treated talc surfaces and talc flotation recovery. However, clear correlations were observed between the flotation recovery of polymer-treated talc and the measured wetting film rupture time and rate of dewetting for a bubble attaching to a talc basal plane surface treated with the polymers. The retardation of the three-phase contact line expansion caused by the adsorbed polymers was found to have the largest influence on the bubble-particle attachment. The effect of the morphology (coverage, distribution, and shape) of the adsorbed layer on the wetting film rupture and the motion of the receding water front is discussed.

Adsorption of dextrin on hydrophobic minerals

The adsorption of dextrin on talc, molybdenite, and graphite (three naturally hydrophobic minerals) has been compared. Adsorption isotherms and in situ tapping mode atomic force microscope (TMAFM) imaging have enabled polymer adsorbed amount and morphology of the adsorbed layer (area coverage and polymer domain size) to be determined and also the amount of hydration water in the structure of the adsorbed layer. The effect of the polymer on the mineral contact angles, measured by the captive bubble method on cleaved mineral surfaces, indicates clear correlations between the hydrophobicity reduction of the minerals, the adsorbed amount, and the surface coverage of the adsorbed polymer. Predictions of the flotation recovery of the treated mineral phases have been confirmed by performing batch flotation experiments. The influence of the polymer surface coverage on flotation recovery has highlighted the importance of this key parameter in the predictions of depressant efficiency. The roles of the initial hydrophobicity and the surface structure of the mineral basal plane in determining adsorption parameters and flotation response of the polymer-treated minerals are also discussed.

The influence of surface hydrophobicity on polyacrylamide adsorption

The adsorption of a modified polyacrylamide on gold surfaces coated with varying proportions of -CH3- and -OH-terminated alkanethiols (producing substrates of varying hydrophobicity: thetac=75, 98, and 119 degrees), was investigated using quartz crystal microbalance with dissipation (QCM-D), tapping-mode atomic force microscopy (TM-AFM), and captive bubble contact angle measurements. The QCM-D data for the polymer adsorbing on the different substrates indicates that the polymer adsorbs faster and to a greater extent on surfaces with higher hydrophobicity. Dissipation data from the QCM-D suggests that the adsorbed polymer undergoes a conformational change when adsorbing onto the substrates of higher hydrophobicity, forming a less rigid extended layer as the adsorption progresses toward the maximum adsorbed amount. AFM imaging of the adsorbed layer illustrates that the polymer layer is incomplete on all three substrates, and that the underlying substrate hydrophobicity has a role in determining the morphology (distribution, coverage, and thickness) of the adsorbed layer. Contact angle measurements of the polymer-coated substrates show variation in the ability of the polymer to reduce the hydrophobicity of the substrates. The role of coverage and distribution of adsorbed polymer on the surface hydrophobicity reduction is discussed.

In situ particle film ATR FTIR spectroscopy of carboxymethyl cellulose adsorption on talc: binding mechanism, pH effects, and adsorption kinetics

Carboxymethyl cellulose (CMC), in solution and adsorbed on the surface of talc, has been studied with ATR FTIR spectroscopy as a function of the solution pH. The solution spectra enable the calculation of the extent of ionization of the polymer (due to protonation and deprotonation of the carboxyl group) at various pH values, yielding a value of 3.50 for the pK(app)(1/2) (pH at which half of all carboxyl groups are ionized) in a simple electrolyte solution and a value of 3.37 for the pK(app)(1/2) in solutions containing magnesium ions (3.33 x 10(-4) M). The spectra of the adsorbed layer reveal that CMC interacts with the talc surface through a chemical complexation mechanism, via the carboxyl groups substituted on the polymer backbone. The binding mechanism is active at all pH values down to pH 2 and up to pH 11. The adsorbed layer spectra reveal that protonation and deprotonation of the polymer are affected by adsorption, with an increase in the pK(app)(1/2) to a value of 4.80. Spectra of the adsorbed polymer were also acquired as a function of the adsorption time. Adsorption kinetic data reveal that the polymer most likely has two different interactions with the talc surface, with a stronger interaction with the talc edge through chemical complexation and a weaker interaction with the talc basal plane presumably through the hydrophobic interaction.

Adsorption of modified dextrins on talc: effect of surface coverage and hydration water on hydrophobicity reduction

The adsorption of three modified dextrins on the basal plane of talc has been studied using in situ tapping mode atomic force microscopy (TMAFM). The images have been used to determine the layer thickness and coverage of the adsorbed polymers. Adsorption isotherms of the polymers on talc particles were also determined using the depletion technique. Values of the adsorbed amount at equilibrium were compared with the volume of adsorbed material as determined using in situ TMAFM, revealing the presence of significant amounts of hydration water in the adsorbed layer structure. This deduction was confirmed by comparing in and ex situ TMAFM images of the adsorbed dextrins. The effect of layer thickness, coverage, and hydration water content on the contact angle of talc particles treated with polymer was investigated using the Washburn method and the equilibrium capillary pressure (ECP) method. Distinct correlations were observed between adsorbed layer properties and the measured contact angles, with the ECP measurements especially highlighting the effect of the adsorbed polymer layer hydration water. The implications for the performance of the modified dextrins in flotation are discussed.