One-pot stereoselective synthesis of chiral 1, 3-oxathiolane by Trichosporon laibachii lipase: Optimization by response surface methodology integrated a desirability function approach

Robust charge carrier by Fe3O4 in Fe3O4/WO3 core-shell photocatalyst loaded on UiO-66(Ti) for urea photo-oxidation

In this study, a facile four-step hydrothermal method was utilized to deposit a core-shell structure on UiO-66(Zr/Ti) nanoflake (NFs) as a visible-light-driven photocatalyst. The core was magnetic Fe₃O₄ which served as a charge carrier coated with WO₃ shell. The as-prepared photocatalyst was characterized by XRD, VSM, BET, FTIR, FE-SEM, UV-Vis-DRS, and PL techniques which proved successful deposition of Fe₃O₄@WO₃ core/shell particle on UiO-66(Zr/Ti)-NFs. The obtained photocatalyst was subsequently applied for urea photo-oxidation. This magnetically recoverable photocatalyst exhibited superior activity due to its desirable band alignment, high stability, and generation of the photo-induced charge carriers, as well as providing a high surface area with low mass transfer resistance. Fe₃O₄ core acted as charge-carrier to transport the photogenerated charges of UiO-66(Zr/Ti)-NFs (electron-donor) to WO₃ charge-collectors for effective photoconversion. The central composite design was applied to design the experiments matrix in which flow rate, pH, irradiation time, catalyst mass, and initial urea concentration were considered as operational factors. The optimized condition was found by defining the desirability function. 90% degradation percentage was achieved at 550 mL/min solution flowrate, pH = 7, 120 min irradiation time, 0.22 g UiO-66(Zr)-NFs-Fe₃O₄@WO_3, and 40 mg/L of the initial concentration of urea with the desirability value of 0.89. Such a superior photocatalytic activity of UiO-66-Fe₃O₄@WO₃ can be ascribed to the reclamation of Fe₃O₄ as a low bandgap carrier, which accelerated the conveyance of electrons and followed surpassing charge separation. Our present findings open a new strategy to produce a wide range of core-shell heterogeneous catalysts to be applied in photoreactors scale-up.

Lipase-mediated direct in situ ring-opening polymerization of ε-caprolactone formed by a chemo-enzymatic method

A novel method to synthesize poly(ε-caprolactone) (PCL) through a three-step, lipase-mediated chemo-enzymatic reaction from cyclohexanone using an immobilized lipase from Trichosporon laibacchii (T. laibacchii) CBS5791 was developed. The immobilized preparation with 1280 U· g^-1 used here was obtained by a method of purification and in situ immobilization where the crude intracellular lipase (cell homogenate) was subjected to partial purification by an aqueous two-phase system (ATPS) consisting of 12% (w/w) polyethylene glycol (PEG) 4000 and 13% (w/w) potassium phosphate (K₂HPO₄) and then in situ immobilization directly on diatomite from the top PEG-rich phase of ATPS. In this multi-step process, the ε-caprolactone (ε-CL) produced by lipase-mediated one-pot two-step chemo-enzymatic oxidation of cyclohexanone was directly subjected to in situ ring-opening polymerization (ROP) started by adding highly hydrophobic solvents. It is necessary to note that ε-CL synthesis and its subsequent ROP were catalyzed by the same lipase. The impact of various reaction parameters, e.g., solvent, cyclohexanone: hydrogen peroxide molar ratio, hydrogen peroxide forms and reaction temperature were investigated. Toluene was selected as a preferred solvent due to supporting the highest molecular weight (M_n = 2168) and moderate ε-CL conversion (65.42%). Through the optimization of reaction conditions, PCL was produced with a M_n of 2283 at 50 °C for 24 h. These results reveal that this lipase-mediated direct ring-opening polymerization of in situ formed ε-CL is an alternative route to the conventional synthesis of PCL.