Tribological behavior of three fatty acid ionic liquids in the lubrication of different material pairs

Methyltrioctylammonium Octadecanoate as Lubricant Additive to Different Base Oils

This study investigates the use of an ionic liquid obtained from fatty acids (FAIL) as an additive at 2 wt.% in two different base oils: a mineral oil (M1) and a polyol ester (E1). Physicochemical characterization of the base oil–FAIL blends confirmed the miscibility of the FAIL in the base oils. The addition of the FAIL hardly changed the density of the base oils and the viscosity slightly increased at lower temperatures. The tribological performance of the base oils and their blends with the FAIL was determined using three different tests: Stribeck curve determination and tribofilm formation tests, both under sliding/rolling motion, and reciprocating wear tests. The M1 + FAIL blend showed the lowest friction values under the mixed lubrication regime due to its higher viscosity, while the E1 + FAIL showed the lowest friction values under the elastohydrodynamic lubrication regime, which may well have been due to its higher polarity. Only the E1 + FAIL blend outperformed the antiwear behavior of the base oil, probably because it has better chemical affinity (higher polarity) for the metallic surface. SEM images showed that the predominant wear mechanism was adhesive-type with plastic deformation and XPS studies proved that the presence of increasing amounts of organic oxygen on the wear scar caused better antiwear performance when the E1 + FAIL blend was used.

The superior lubricating performance and unique mechanism of oil-soluble protic ionic liquids with short alkyl chains

HYPOTHESIS

Ionic liquids (ILs), as lubricant additives, can greatly improve the lubricating behavior of the frictional interfaces. However, it is urgent to explore ILs with good oil solubility in nonpolar oils, and it is necessary to further study and verify the lubrication mechanism of ILs from the perspective of alkyl chain length.

EXPERIMENTS

Five protic ILs (PILs) with varying alkyl chain lengths were synthesized by proton transfer method. As additives in PAO oil, their tribological properties were investigated on SRV-V tester. Through molecular dynamics simulation, the adsorption behavior of PILs at the frictional interface was illustrated.

FINDINGS

The tribological properties of base oil could be significantly improved by adding PIL additives, but interestingly, PILs with short-chain anions showed better lubricating performance, which contradicted most of the early findings. Further analyses revealed that PILs achieved effective lubrication by the tribochemical interaction between anions and frictional interface, and the formation of cationic protective layer. However, PILs with shorter-chain anions form a denser protective layer that can better support the interfacial anions to participate in tribochemical reactions and thus abnormally exhibit superior lubricating performance than those with longer-chain anions.

Friction, Wear and Corrosion Behavior of Environmentally-Friendly Fatty Acid Ionic Liquids

This research deals with the tribological behavior and corrosion performance of three novel fatty acid anion-based ionic liquids (FAILs): methyltrioctylammonium hexanoate ([N8,8,8,1][C6:0]), methyltrioctylammonium octadecanoate ([N8,8,8,1][C18:0]) and methyltrioctylammonium octadec-9-enoate ([N8,8,8,1][C18:1]), employed for the first time as neat lubricant with five different material pairs: steel–steel, steel–aluminum alloy, steel–bronze, steel–cast iron and steel–tungsten carbide. These novel substances were previously obtained from fatty acids via metathesis reactions, identified structurally via NMR (nuclear magnetic resonance) and FTIR (Fourier-transform infrared spectroscopy) techniques, and then characterized from a physicochemical (density, water solubility, viscosity, viscosity index and refractive index) and environmental (bacterial toxicity and biodegradability) points of view. The corrosion behavior of the three FAILs was studied by exposure at room temperature, while friction and wear tests were performed with a reciprocating ball-on-disc configuration. The main results and conclusions obtained were: (1) Corrosion in the presence of the three FAILs is observed only on the bronze surface; (2) All FAILs presented similar tribological behavior as lubricants for each tested material pair; (3) XPS (X-ray photoelectron spectroscopy) analysis indicated that the surface behavior of the three FAILs in each material pair was similar, with low chemical interaction with the surfaces.

A review on tribological performance of ionic liquids as additives to bio lubricants

All the moving components in an internal combustion engine require a lubricant that allows smooth sliding and/or rolling of interacting surfaces. Lubricant not only minimizes the friction and wear but also dissipates the heat generated due to friction and removes debris from the area of contact. Environmental concerns, decreasing mineral oil reserves and difficult disposal of nonbiodegradable conventional lubricants have urged the researchers to shift towards environmental-friendly lubricants. Number of tribological studies carried out in the past have proved that ionic liquid-based bio-lubricants are sustainable and biodegradable alternative to mineral oils. This paper presents a brief review of properties of ionic liquids and their ability to reduce friction and wear between the interacting surfaces. Tribological performance and compatibility of ionic liquids with various base-oils have been compared under boundary lubrication. The results reveal that phosphonium-based ionic liquids namely tetra-decyl tri-hexyl phosphonium bis(2,4,4-trimethylpentyl) phosphinate (P66614)i(C8)2PO2 and tri-hexyl tetra-decyl phosphonium bis(2-ethylhexyl) phosphate (P-DEHP) are more suitable for tribological applications. Since, ionic liquids can be tailored according to the application and millions of combinations are possible therefore, there is a need to summarize the published data in a more systematic and logical way.