Selective recovery of gold ions in aqueous solutions by a novel trithiocyanuric-Zr based MOFs adsorbent

Efficient recovery of gold from solution with a thiocyanate-modified Zr-MOF: adsorption properties and DFT calculations

The design and development of new large-capacity and selective materials for extracting rare precious metals via electronic waste is practically essential. In this paper, a new efficient UiO-66-NCS has been obtained as a consequence of the modification of the classical Zr-MOF (UiO-66-NH2), and its ability to recover gold has been investigated. These batch results adequately illustrated that UiO-66-NCS exhibited good adsorption capacity (675.5 mg g-1) and exceptional selectivity. In addition, UiO-66-NCS achieved faster adsorption equilibrium times of about 120 min. Adsorption kinetics and isotherms demonstrated that the pseudo-second-order adsorption scheme and a Langmuir-type procedure were shown by the adsorption of Au(III) on UiO-66-NCS. Characterized by pH effect experiments, TEM, XRD, and XPS, the adsorption of UiO-66-NCS with Au(III) relies on coordination, which further results in reduction, and the generated Au(0) is uniformly dispersed in the MOF. The adsorbent has considerable advantages for cyclic regeneration. Finally, DFT fitting results showed that the adsorption binding energy of UiO-66-NCS with [AuCl4]- was -8.63 kcal mol-1 for the adsorption process. UiO-66-NCS is likely to be an ideal substance for gold recovery.

Coordination polymer gel mediated spectrophotometric, ICP-AES and spectrofluorimetric methods for trace As(III) determination in water and food samples

Herein, a coordination polymer gel is proposed for the determination of As(III) in real samples through multispectroscopic techniques viz. spectrophotometry, spectrofluorimetry, and inductively coupled plasma atomic emission spectroscopy (ICP-AES). Taguchi L32 (46 21) design and adaptive neuro fuzzy inference system (ANFIS) optimized the controllable factors affecting the extraction yielding an experimental S/N ratio of 39.94 dB. The fluorescence quenching (KSV = 2.63 × 106 L mol-1) was static with photoelectron transfer being the main mechanism confirmed by the density functional theory calculations. The limits of detection (LODs), limits of quantification (LOQs) and linear ranges were 0.038 μg L-1, 0.13 μg L-1 and 1.67-116.67 μg L-1, 0.40 μg L-1, 1.21 μg L-1 and 1.67-33.33 μg L-1, 1.07 μg L-1, 3.24 μg L-1 and 3.32-35.37 μg L-1 for the developed enrichment coupled ICP-AES, spectrophotometry and fluorescence sensing methods. Among these methods, the enrichment - ICP-AES method has the lowest LOD, LOQ and the widest linear range followed by the enrichment - spectrophotometry and fluorescene sensing methods. Spectrofluorimetry offers high sensitivity, selectivity, and possible real time monitoring, spectrophotometry provides a cost-effective and versatile option, while ICP-AES manifests multi-element analysis with high sensitivity and low interference. The developed methods were validated and employed for the successful determination of trace As(III) in real samples. The employment of these methods enhances the overall analytical capability for a wide range of sample types and concentrations.

Sustainable Recovery of Platinum Group Metals from Spent Automotive Three-Way Catalysts through a Biogenic Thiosulfate-Copper-Ammonia System

This study explores an eco-friendly method for recovering platinum group metals from a synthetic automotive three-way catalyst (TWC). Bioleaching of palladium (Pd) using the thiosulfate-copper-ammonia leaching processes, with biogenic thiosulfate sourced from a bioreactor used for biogas biodesulfurization, is proposed as a sustainable alternative to conventional methods. Biogenic thiosulfate production was optimized in a gas-lift bioreactor by studying the pH (8-10) and operation modes (batch and continuous) under anoxic and microaerobic conditions for 35 d. The maximum concentration of 4.9 g S2O32- L-1 of biogenic thiosulfate was reached under optimal conditions (batch mode, pH = 10, and airflow rate 0.033 vvm). To optimize Pd bioleaching from a ground TWC, screening through a Plackett-Burman design determined that oxygen and temperature significantly affected the leaching yield negatively and positively, respectively. Based on these results, an optimization through an experimental design was performed, indicating the optimal conditions to be Na2S2O3 1.2 M, CuSO4 0.03 M, (NH4)2SO4 1.5 M, Na2SO3 0.2 M, pH 8, and 60 °C. A remarkable 96.2 and 93.2% of the total Pd was successfully extracted from the solid at 5% pulp density using both commercially available and biogenic thiosulfate, highlighting the method's versatility for Pd bioleaching from both thiosulfate sources.

Selective adsorption of mercury ion from water by a novel functionalized magnetic Ti based metal-organic framework composite

In the context of industrialization and severe wastewater pollution, mercury ions pose a major threat due to their high toxicity. However, traditional adsorbents and common metal-organic framework (MOF) materials have limited effectiveness. This study focuses on combining magnetic materials with functionalized titanium-based MOF composite (SNN-MIL-125(Ti)@Fe3O4) to improve mercury ion adsorption. Through comprehensive characterization and analysis, the adsorption performance and mechanism of the material were studied. The optimal adsorption of the material was achieved at pH 5, exhibiting a pseudo-second-order adsorption model and the Hill theoretical capacity of 668.98 mg/g. Hill and Tempkin models confirmed the presence of chemical and physical adsorption sites on the material surface. Thermodynamic experiments showed a spontaneous endothermic process. Despite the presence of interfering ions, the material exhibited high selectivity for mercury ions. After four cycles, adsorption performance decreased by only 8%, indicating excellent reusability. Nitrogen- and sulfur-containing functional groups played a key role in mercury ion adsorption. In conclusion, SNN-MIL-125(Ti)@Fe3O4, as a magnetic MOF adsorption material, showed potential for effective remediation of mercury-contaminated wastewater. This study contributes to the development of efficient adsorption materials and enhances the understanding of their mechanism.

Schiff base-functionalized metal-organic frameworks as an efficient adsorbent for the decontamination of heavy metal ions in water

Adsorptive removal of heavy metal ions from water is an energy- and cost-effective water decontamination technology. Schiff base functionalities can be incorporated into the pore cages of metal-organic frameworks (MOFs) via direct synthesis, post-synthetic modification, and composite formation. Such incorporation can efficiently enhance the interactions between the MOF adsorbent and target heavy metal ions to promote the selective adsorption of the latter. Accordingly, Schiff base-functionalized MOFs have great potential to selectively remove a particular metal ion from the aqueous solutions in the presence of coexisting (interfering) metal ions through the binding sites within their pore cages. Schiff base-functionalized MOFs can bind divalent metal ions (e.g., Pb(II), Co(II), Cu(II), Cd (II), and Hg (II)) more strongly than trivalent metal ions (e.g., Cr(III)). The adsorption capacity range of Schiff base-functionalized MOFs for divalent ions is thus much more broad (22.4-713 mg g-1) than that of trivalent metal ions (118-127 mg g-1). To evaluate the adsorption performance between different adsorbents, the two parameters (i.e., adsorption capacity and partition coefficient (PC)) are derived and used for comparison. Further, the possible interactions between the Schiff base sites and the target heavy metal ions are discussed to help understand the associated removal mechanisms. This review delivers actionable knowledge for developing Schiff-base functionalized MOFs toward the adsorptive removal of heavy metal ions in water in line with their performance evaluation and associated removal mechanisms. Finally, this review highlights the challenges and forthcoming research and development needs of Schiff base-functionalized MOFs for diverse fields of operations.

Turning precious metal-loaded e-waste to useful catalysts: Investigation into supercilious recovery and catalyst viability for peroxymonosulfate activation

Here, the key tasks to be accomplished are selective precious metal recovery from e-wastewater and their conversion into valuable catalysts for peroxymonosulfate (PMS) activation. In this regard, we developed a hybrid material using 3D functional graphene foam and copper para-phenylenedithol (Cu-pPDT) MOF. The prepared hybrid showed a supercilious recovery of 92-95% even up to five cycles for Au(III) and Pd(II), which can be viewed as a reference for both the 2D graphene and the MOFs family. The outstanding performance has been attributed principally to the impact of diverse functionality as well as the unique morphology of 3D graphene foam, which provided a wide range of surface area and additional active sites in the hybrid frameworks. To prepare the surface-loaded metal nanoparticle catalysts, the sorbed samples recovered after precious metal extraction were calcined at 800 °C. The viability of the developed catalysts for the breakdown of 4-nitrophenol (4-NP) via PMS activation was investigated. Electron paramagnetic resonance spectroscopy (EPR) and experiments with radical scavengers suggest that sulfate and hydroxyl radicals are the main reactive species involved in the breakdown of 4-NP. This is because the active graphitic carbon matrix and the exposed precious metal and copper active sites work together in a way that is more effective.

A novel S,N-rich MOF for efficient recovery of Au(III): Performance and mechanism

A novel S,N-rich MOF with adenine and 4,4'-thiodiphenol as organic ligands was synthesized via the one-step solvothermal method, and used for gold recovery. The pH impact, adsorption kinetics, isotherms, thermodynamics, selectivity, and reusability were investigated accordingly. The adsorption and desorption mechanism were also explored comprehensively. The electronic attraction, coordination, and in situ redox account for the Au(III) adsorption. The Au(III) adsorption is affected strongly by the pH of solutions, and best at pH of 2.57. The MOF exhibits exceptional adsorption capacity as high as 3680 mg/g at 55 °C, fast kinetics with 8 min for 9.6 mg/L Au(III), and excellent selectivity for gold ion in real e-waste leachates. The adsorption process of gold on the adsorbent is endothermic and spontaneous, and influenced visibly by temperature. The adsorption ratio still maintained 99% after seven adsorption-desorption cycles. The column adsorption experiments show that the MOF has outstanding selectivity for Au(III) with 100% of removal efficiency in a complex solution containing Au, Ni, Cu, Cd, Co, and Zn ions. A glorious adsorption with a breakthrough time of 532 mins was obtained for the breakthrough curve. This study not only provides an efficient adsorbent for gold recovery, but also guidance for designing new materials.

Improvement of gold bioleaching extraction from waste telecommunication printed circuit boards using biogenic thiosulfate by Acidithiobacillus thiooxidans

Cyanide usage in gold processing techniques has become increasingly challenging due to its toxicity and environmental impact. It is possible to develop environmentally friendly technology using thiosulfate because of its nontoxic characteristics. Thiosulfate production requires high temperatures, resulting in high greenhouse gas emissions and energy consumption. The biogenesized thiosulfate is an unstable intermediate product of Acidithiobacillus thiooxidans sulfur oxidation pathway to sulfate. A novel eco-friendly method was presented in this study to treat spent printed circuit boards (STPCBs) using biogenesized thiosulfate (Bio-Thio) obtained from Acidithiobacillus thiooxidans cultured medium. To obtain a preferable concentration of thiosulfate among other metabolites by limiting thiosulfate oxidation, optimal concentrations of inhibitor (NaN₃: 3.25 mg/L) and pH adjustments (pH= 6-7) were found to be effective. Selection of the optimal conditions has led to the highest bio-production of thiosulfate (500 mg/L). The impact of STPCBs content, ammonia, ethylenediaminetetraacetic acid (EDTA), and leaching time on Cu bio-dissolution and gold bio-extraction were investigated using enriched-thiosulfate spent medium. The suitable conditions were a pulp density of 5 g/L, an ammonia concentration of 1 M, and a leaching time of 36 h, which led to the highest selective extraction of gold (65 ± 0.78%).

Efficient Recovery of Noble Metal Ions (Pd2+, Ag+, Pt2+, and Au3+) from Aqueous Solutions Using N,N'-Bis(salicylidene)ethylenediamine (Salen) as an Extractant (Classic Solvent Extraction) and Carrier (Polymer Membranes)

This paper presents the results of the first application of N,N'-bis(salicylidene)ethylenediamine (salen) as an extractant in classical liquid-liquid extraction and as a carrier in membrane processes designed for the recovery of noble metal ions (Pd2+, Ag+, Pt2+, and Au3+) from aqueous solutions. In the case of the utilization of membranes, both sorption and desorption were investigated. Salen has not been used so far in the sorption processes of precious metal ions. Recovery experiments were performed on single-component solutions (containing only one type of metal ions) and polymetallic solutions (containing ions of all four metals). The stability constants of the obtained complexes were determined spectrophotometrically. In contrast, electrospray ionization high-resolution mass spectrometry (ESI-HRMS) was applied to examine the elemental composition and charge of the generated complexes of chosen noble metal ions and salen molecules. The results show the great potential of N,N'-bis(salicylidene)ethylenediamine as both an extractant and a carrier. In the case of single-component solutions, the extraction percentage was over 99% for all noble metal ions (molar ratio M:L of 1:1), and in the case of a polymetallic solution, it was the lowest, but over 94% for platinum ions and the highest value (over 99%) for gold ions. The percentages of sorption (%Rs) of metal ions from single-component solutions using polymer membranes containing N,N'-bis(salicylidene)ethylenediamine as a carrier were highest after 24 h of the process (93.23% for silver(I) ions, 74.99% for gold(III) ions, 69.11% and 66.13% for palladium(II) and platinum(II) ions, respectively), similar to the values obtained for the membrane process conducted in multi-metal solutions (92.96%, 84.26%, 80.94%, and 48.36% for Pd(II), Au(III), Ag(I), and Pt(II) ions, respectively). The percentage of desorption (%Rdes) was very high for single-component solutions (the highest, i.e., 99%, for palladium solution and the lowest, i.e., 88%, for silver solution), while for polymetallic solutions, these values were slightly lower (for Pt(II), it was the lowest at 63.25%).