Green synthesis of Fe3O4-onion peel biochar nanocomposites for adsorption of Cr(VI), methylene blue and congo red dye from aqueous solutions

Effect mechanism of iron conversion on adsorption performance of hydrochar derived from coking sludge

In this study, Fe conversion during hydrothermal carbonization (HTC) of coking sludge were investigated, and the effect mechanism of Fe component on the adsorption performance of coking sludge hydrochar (CHC) was explored. The results showed that after HTC treatment, more than 95 % of Fe remained in the CHC. Fe3+ was reduced to Fe2+ by sugar and amino acids. Fe was stabilized during the HTC process and was still predominantly in the Fe manganese oxidation state. The CHC prepared at 270 °C exhibited excellent adsorption capacities for Congo red (CR), tetracycline (TC), and Cr (VI). Their maximum adsorption capacities were 140.85, 147.06, and 19.92 mg/g, respectively. Quantitative adsorption mechanism experiments, XRD and VSM characterization revealed that Fe component played a significant role in adsorption, and CHC with more Fe3O4 exhibited better adsorption capacity. The results of the XPS characterization of CHC before and after adsorption showed that Fe3O4 provided rich Fe adsorption sites on the surface of CHC to strengthen the adsorption efficiency of pollutants through Fe3+/Fe2+ reduction and complexation of Fe-O/N. In addition, the formed Fe3O4 also imparted CHC with magnetic properties (Ms = 4.12 emu/g) to facilitate the subsequent separation and recovery. These results demonstrated that the prepared CHC has great potential for treating actual wastewater containing CR and TC.

Removal of Cr(VI) ions from wastewater by Fe3O4-loaded porous sludge biochar

In this work, porous sludge biochar (PSBC) was prepared by molten salt-assisted pyrolysis of municipal sludge, and PSBC loaded with Fe3O4 (Fe3O4@PSBC) was synthesized by chemical precipitation. The effects of pH (2.0-10.0), sorbent dosage (0.1-2 g/L), coexisting ions (Ca2+, Mg2+, Cu2+, Pb2+, Cl-, SiO32-, NO3-, CO32-, SO42-, and PO43-), adsorption temperature (288, 298, and 308 K), initial Cr(VI) ion concentrations (50-150 mg/L), and adsorption time (5-300 min) on the removal of Cr(VI) ions by the sorbent were investigated. The mechanism of the removal of Cr(VI) ions was characterized by scanning electron microscope (SEM), Fourier transform infrared (FTIR), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The result showed that the removal of Cr(VI) ions on PSBC and Fe3O4@PSBC had a strong dependence on the pH of solution. The maximum adsorption capacity of Cr(VI) ions by PSBC and Fe3O4@PSBC was 162 and 209 mg/g, respectively, at a dosage of 0.4 g/L, pH of 3, and temperature of 298 K. The removal process of Cr(VI) ions could be fitted by the Langmuir isotherm model and pseudo-second-order kinetic model. The breakthrough curves were in good agreement with the theoretical values of the Thomas model. The mechanism of the removal of Cr(VI) ions by Fe3O4@PSBC mainly contain complexation, reduction, and electrostatic interaction. This work proposes a new removal material for Cr(VI)-containing wastewater.

Iron-engineered mesoporous biocarbon composite and its adsorption, activation, and regeneration approach for removal of paracetamol in water

Three-dimensional multi-porous Iron Oxide/carbon (Fe₂O₃/C) composites derived from tamarind shell biomass were synthesized by a single-step co-pyrolysis technique and utilized for Paracetamol (PAC) dismissal in the combined adsorption, and advanced oxidation such as electrochemical regeneration techniques. The Fe₂O₃/C composites were prepared by different pyrolysis temperatures, and named as TS750 (without Fe₂O₃at 750 °C), MTS450 BCs (Low-450 °C), MTS600 BCs (Moderate-600 °C) and MTS750 BCs (high-750 °C), respectively. As-prepared Fe₂O₃/C composite was characterized by FE-SEM, XRD, BET, and XPS analysis. The specific surface area and the spatial interaction between the interlayers of Fe₂O₃ and C were significantly improved by increasing the pyrolysis temperatures from 450 to 750 °C, which improved the adsorption capacity of Fe₂O₃/C composites in terms of higher rate constants and chemisorption kinetics. The Pseudo-second-order kinetics model fitted in the adsorption test results of Fe₂O₃/C composites with the highest correlation co-efficiency. The Langmuir-isotherms model fitted in the adsorption test of the TS750 and MTS450 BCs. The Freundlich isotherms model is more fit with MTS600 and MTS750 BCs. Based on the isotherm results, the MTS750 BCs achieved 46.9 mg/g of maximum PAC adsorption capacity. The optimized MTS750 composites could be completely recovered by using an advanced electrochemical oxidation regeneration approach within 180 min. Also, with the adsorption and recovery process, the TOC removal rate improved to ∼79.4%. After the 6th cycle electrochemical oxidation process, the obtained results of the re-adsorption test showed the stabile adsorption activity of the sorbent material. The data outcomes herein propose that this type of combined adsorption and electrochemical approach will be useful in commercial water treatment plants.

Bio-inspired sustainable synthesis of novel SnS2/biochar nanocomposite for adsorption coupled photodegradation of amoxicillin and congo red: Effects of reaction parameters, and water matrices

This study aims to fabricate a novel integrated photocatalytic adsorbent (IPA) via a green solvothermal process employing tea (Camellia sinensis var. assamica) leaf extract as a stabilizing and capping agent for the removal of organic pollutants from wastewater. An n-type semiconductor photocatalyst, SnS_2, was chosen as a photocatalyst due to its remarkable photocatalytic activity supported over areca nut (Areca catechu) biochar for the adsorption of pollutants. The adsorption and photocatalytic properties of fabricated IPA were examined by taking amoxicillin (AM) and congo red (CR) as two emerging pollutants found in wastewater. Investigating synergistic adsorption and photocatalytic properties under varying reaction conditions mimicking actual wastewater conditions marks the novelty of the present research. The support of biochar for the SnS₂ thin films induced a reduction in charge recombination rate, which enhanced the photocatalytic activity of the material. The adsorption data were in accordance with the Langmuir nonlinear isotherm model, indicating monolayer chemosorption with the pseudo-second-order rate kinetics. The photodegradation process follows pseudo-first-order kinetics with the highest rate constant of 0.0450 min^-1 for AM and 0.0454 min^-1 for CR. The overall removal efficiency of 93.72 ± 1.19% and 98.43 ± 1.53% could be achieved within 90 min for AM and CR via simultaneous adsorption and photodegradation model. A plausible mechanism of synergistic adsorption and photodegradation of pollutants is also presented. The effect of pH, Humic acid (HA) concentration, inorganic salts and water matrices have also been included.The photodegradation activity of SnS₂ under visible light coupled with the adsorption capability of the biochar results in the excellent removal of the contaminants from the liquid phase.

New insights on manganese dioxide nanoparticles loaded on cellulose-based biochar of cassava peel for the adsorption of three cationic dyes from wastewater

Herein, a cost-effective nanomaterial with excellent adsorption capacity, simply prepared, using manganese dioxide (MnO₂) nanoparticles (NP) loaded on cellulose-based biochar of an agricultural waste, which is cassava peel carbon (CPC) and denoted as MnO₂-NP-CPC. MnO₂-NP-CPC is an environmental-friendly, and efficient adsorbent analyzed using different technics such as x-ray diffraction (XRD), Fourier-transformed infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and energy dispersive x-ray spectroscopy (EDX). MnO₂-NP-CPC was used to remove three different toxic dyes; methylene blue (MB), malachite green (MG), and rhodamine b (RB) from a single (MB), (MG), (RB), binary (MB + MG), (MG + RB), (MB + RB) and ternary (MB + MG + RB) wastewater systems, the impact of pH, adsorbent dose (2-8), initial dye concentrations (10-30 mg/L), temperature (15-35 °C) were fully studied. Furthermore, all the sorption experiments were done including adsorption isotherms, kinetics, and thermodynamics to explore all the mechanisms involved in the sorption of the three ionic dyes in single, binary, and ternary systems. The equilibrium experiments data fitted well the monolayer Langmuir isotherm for the single dye system with correlation coefficients close to 1 (0.98 for MB, 0.99 for MG, and 0.86 for RB), while the extended Langmuir and extended Freundlich isotherms were investigated to study the interaction of the three dyes in their binary systems, the obtained results indicate clearly that the sorption fellows the extended Langmuir model. Besides, the kinetic study showed the applicability of the pseudo-second model for the three dyes. Finally, the thermodynamic adsorption was controlled by physisorption, endothermic, and spontaneous in nature.

Adsorption of Congo red dye in water by orange peel biochar modified with CTAB

In order to improve the adsorption effect of biochar on Congo red dye, this study used hexadecyl trimethyl ammonium bromide (CTAB) to organically modify orange peel biochar (OBC) to produce CTAB-modified orange peel biochar (NOBC), and the biochar before and after modification was analyzed by SEM-EDS, FTIR and BET. The adsorption performance of NOBC on Congo red dye was investigated and the adsorption mechanism was studied. The results showed that the adsorption amount was influenced by the initial concentration, adsorption time and solution pH. NOBC adsorbed 50 mg L^-1 CR with an equilibrium time of 60 min and an equilibrium amount of 290.1 mg g^-1, while the adsorption equilibrium time of OBC was 210 min and an equilibrium amount of 155.2 mg g^-1, the adsorption of CR by NOBC was above 210 mg g^-1 at pH 2 to 11, NOBC can be recycled three times. The experimental results showed that the adsorption data of CR on NOBC were consistent with the Langmuir isothermal adsorption model and the Pseudo-second-order model, and the mechanism of CR adsorption on NOBC mainly included electrostatic attraction and surface adsorption. In conclusion, NOBC is a promising material for dye wastewater adsorption.

The efficient removal of congo red and ciprofloxacin by peony seeds shell activated carbon with ultra-high specific surface area

Preparation of high-performance activated carbon from agroforestry waste biomass can effectively improve the shortcomings of traditional biomass carbon performance. Using the waste biomass peony seeds shell (PSS) as the precursors in this study, high performance activated carbon was prepared by the KOH two-step activation method and used to remove congo red (CR) and ciprofloxacin (CIP) in water pollution. The obtained PSS-based activated carbons (PSACs) were characterized by SEM, EDS, N₂ adsorption-desorption isotherm, FTIR, and XRD methods. The results showed that the activated carbon at 700 °C (PSAC-700) had an ultra-high specific surface area (2980.96 m²/g), excellent micropore volume (1.12 cm³/g), and abundant surface functional groups. The results of adsorption performance revealed that PSAC-700 exhibited excellent adsorption capacity for CR (q_max = 2003.2 mg/g) and CIP (q_max = 782.3 mg/g), which was superior to the carbon-based adsorbents reported reviously in the literature. Langmuir model could well describe the adsorption process of PSACs for CR and CIP, indicating that the pollutant molecules were uniformly adsorbed on the surface monolayer. The regeneration experiment suggested that after three cycles, the adsorption capacities of PSAC-700 for CR and CIP reached 1814 mg/g and 697 mg/g, respectively, with good repeatability. The preparation of PSAC-700 in this study has high adsorption capacity and strong application, which is an ideal material for wastewater purification adsorbent and has broad application prospect.

Synthesis of Green Magnetite/Carbonized Coffee Composite from Natural Pyrite for Effective Decontamination of Congo Red Dye: Steric, Synergetic, Oxidation, and Ecotoxicity Studies

Green magnetite/carbonized spent coffee (MG/CFC) composite was synthesized from natural pyrite and characterized as an adsorbent and catalyst in photo-Fenton’s oxidation system of Congo red dye (C.R). The absorption behavior was illustrated based on the steric and energetic parameters of the advanced Monolayer equilibrium model of one energetic site (R2 > 0.99). The structure exhibits 855 mg/g as effective site density which induces its C.R saturation adsorption capacity to 436.1 mg/g. The change in the number of absorbed C.R per site with temperature (n = 1.53 (293) to 0.51 (313 K)) suggests changes in the mechanism from multimolecular (up to 2 molecules per site) to multianchorage (one molecule per more than one site) processes. The energetic studies (ΔE = 6.2–8.2 kJ/mol) validate the physical uptake of C.R by MG/CFC which might be included van der Waals forces, electrostatic attractions, and hydrogen bonding. As a catalyst, MG/CFC exhibits significant activity during the photo-Fenton’s oxidation of C.R under visible light. The complete oxidation of C.R was detected after 105 min (5 mg/L), 120 min (10 mg/L), 135 min (15 mg/L), 180 min (20 mg/L), and 240 min (25 mg/L) using MG/CFC at 0.2 g/L dosage and 0.1 mL of H2O2. Increasing the dosage up to 0.5 g/L reduce the complete oxidation interval of C.R (5 mg/L) down to 30 min while the complete mineralization was detected after 120 min. The acute and chronic toxicities of the treated samples demonstrate significant safe products of no toxic effects on aquatic organisms as compared to the parent C.R solution.

Adsorption Characteristics and Mechanism of Methylene Blue in Water by NaOH-Modified Areca Residue Biochar

To solve the water pollution problem caused by methylene blue (MB), areca residue biochar (ARB) was prepared by pyrolysis at 600 °C, and modified areca residue biochar (M-ARB) was obtained by modifying ARB with 1.5 mol/L NaOH, and they were utilized to adsorb and eliminate MB from water. The structural characteristics of ARB and M-ARB were examined, and the main influencing factors and adsorption mechanism of MB adsorption process were investigated. The outcomes demonstrated an increase in M-ARB’s specific surface area and total pore volume of 66.67% and 79.61%, respectively, compared with ARB, and the pore structure was more abundant, and the content of oxygen element was also significantly increased. When the reaction temperature was 25 °C, starting pH of the mixture was 10, the initial MB concentration was 50 mg/L, the ARB and M-ARB dosages were 0.07 g/L and 0.04 g/L, respectively, the adsorption equilibrium was achieved at about 210 min, and the elimination rate for MB exceeded 94%. The adsorption behaviors of ARB and M-ARB on MB were more in line with the Langmuir isotherm model (R2 > 0.95) and the quasi-secondary kinetic model (R2 > 0.97), which was characterized by single-molecule layer chemisorption. The highest amount of MB that may theoretically be absorbed by M-ARB in water ranging from 136.81 to 152.72 mg/g was 74.99–76.59% higher than that of ARB. The adsorption process was a spontaneous heat absorption reaction driven by entropy increase, and the adsorption mechanism mainly involved electrostatic gravitational force, pore filling, hydrogen bonding, and π–π bonding, which was a complex process containing multiple mechanisms of action. NaOH modification can make the ARB have more perfect surface properties and more functional group structures that can participate in the adsorption reaction, which can be used as an advantageous adsorption material for MB removal in water.

Enhanced Congo Red Adsorption and Photo-Fenton Oxidation over an Iron-Impeded Geopolymer from Ferruginous Kaolinite: Steric, Energetic, Oxidation, and Synergetic Studies

An iron-impeded geopolymer (Fe/GP) was synthesized from natural ferruginous kaolinite and optical waste for enhanced decontamination of Congo red (CR) dye. The adsorption properties of Fe/GP were assessed using an advanced monolayer equilibrium model of one energy (R ² > 0.99). Fe/GP possessed an active site density of 391.3 mg/g, which induced an adsorption capacity of 634 mg/g at the saturation state. The number of adsorbed CR molecules per site (n = 1.56-1.62) reflected the possible uptake of two molecules per site via a multimolecular mechanism. The adsorption energy (5.12-5.7 kJ/mol) reflected the physical adsorption of the CR molecules via hydrogen bonding and/or van der Waals forces. As a catalyst, notable activity toward photo-Fenton oxidation was achieved even at high CR concentrations. Complete oxidation was observed after 30 (CR concentration: 10 mg/L), 50 (20 mg/L), 80 (30 mg/L), 120 (40 mg/L), and 140 min (50 mg/L). High oxidation efficiency was achieved using 0.1 g/L Fe/GP, 0.1 mL of hydrogen peroxide (H₂O₂), and a visible light source. Increasing the Fe/GP dosage to 0.3 g/L resulted in complete oxidation of CR (100 mg/L) after 220 min. Therefore, synthetic Fe/GP can be used as a low-cost and superior catalyst and adsorbent for the removal of CR-based contaminants via adsorption or advanced oxidation processes.

Iron/titanium oxide-biochar (Fe2TiO5/BC): A versatile adsorbent/photocatalyst for aqueous Cr(VI), Pb2+, F- and methylene blue

This is the first report of the metal Fe-Ti oxide/biochar (Fe₂TiO₅/BC) composite for simultaneous removal of aqueous Pb²⁺, Cr⁶⁺, F^- and methylene blue (MB). Primary Fe₂TiO₅ nano particles and aggregates were dispersed on a high surface area Douglas fir BC (∼700 m²/g) by a simple chemical co-precipitation method using FeCl₃ and TiO(acac)₂ salts treated by base and heated to 80 °C. This was followed by calcination at 500 °C. This method previously was used without BC to make the neat mixed oxide Fe₂TiO₅, exhibiting a lower energy band gap than TiO₂. Adsorption of Cr(VI), Pb(II), fluoride, and MB on Fe₂TiO₅/BC was studied as a function of pH, equilibrium time, initial adsorbate concentration, and temperature. Adsorption isotherm studies were conducted at 5, 25, and 45 ℃ and kinetics for all four adsorbates followed the pseudo second order model. Maximum Langmuir adsorption capacities for Pb²⁺, Cr⁶⁺, F^- and MB at their initial pH values were 141 (pH 2), 200 (pH 5), 36 (pH 6) and 229 (pH 6) mg/g at 45 ℃ and 114, 180, 26 and 210 mg/g at 25 ℃, respectively. MB was removed from the water on Fe₂TiO₅/BC by synergistic adsorption and photocatalytic degradation at pH 3 and 6 under UV (365 nm) light irradiation. Cr⁶⁺, Pb²⁺, F^-, and MB each exhibited excellent removal capacities in the presence of eight different competitive ions in simulated water samples. The removal mechanisms on Fe₂TiO₅/BC and various competitive ion interactions were proposed. Some iron ion leaching at pH 3 catalyzed Photo-Fenton destruction of MB. Fe₂TiO₅, BC, and Fe₂TiO₅/BC bandgaps were studied to help understand photocatalysis of MB and to advance supported metal oxide photodegradation using smaller energy band gaps than the larger bandgap of TiO₂ for water treatment. A long range goal is to photocatalytically destroy some sorbates with adsorbents to avoid the need for regeneration steps.