Competitive adsorption of asphaltene and n-heptane on quartz surfaces and its effect on crude oil transport through nanopores

Molecular Insights into Soaking in Hybrid N2-CO2 Huff-n-Puff: A Case Study of a Single Quartz Nanopore-Hydrocarbon System

Hybrid N2-CO2 huff-n-puff (HnP) has been experimentally demonstrated to be a promising approach for improving oil recovery from tight/ultratight shale oil reservoirs. Despite this, the detailed soaking process and interaction mechanisms remain unclear. Adopting molecular dynamic simulations, the soaking behavior of hybrid N2-CO2 HnP was investigated at the molecular and atomic levels. Initially, the soaking process of fluid pressure equilibrium after injection pressure decays in a single matrix nanopore connected to a shale oil reservoir is studied. The study revealed that counter-current and cocurrent displacement processes exist during the CO2 and hybrid N2-CO2 soaking, but cocurrent displacement occurs much later than counter-current displacement. Although the total displacement efficiency of the hybrid N2-CO2 soaking system is lower than that of the CO2 soaking system, the cocurrent displacement initiates earlier in the hybrid N2-CO2 soaking system than in the CO2 soaking system. Moreover, the N2 soaking process is characterized by only counter-current displacement. Next, the soaking process of fluid pressure nonequilibrium before the injection pressure decays is investigated. It was discovered that counter-current and cocurrent displacement processes initiate simultaneously during the CO2, N2, and hybrid N2-CO2 soaking process, but cocurrent displacement exerts a dominant influence. During the CO2 soaking process, many hydrocarbon molecules in the nanopore are dissolved in CO2 while simultaneously exhibiting a substantial retention effect in the nanopore. After pure N2 injection, there is a tendency to form a favorable path of N2 through the oil phase. The injection of hybrid CO2-N2 facilitates the most significant cocurrent displacement effect and the reduction in residual oil retained in the nanopore during the soaking process, thus resulting in the best oil recovery. However, the increase rate in total displacement efficiencies of the different soaking systems over time (especially the hybrid N2-CO2 soaking system) was significantly larger before than after injection pressure decays. Additionally, the displacement effect induced by oil volume swelling is significantly restricted before the injection pressure decays compared to the soaking process after the injection pressure decays. This study explains the role of CO2-induced oil swelling and N2-induced elastic energy played by hybrid N2 and CO2 at different stages of the hybrid N2-CO2 soaking process before and after pressure decays and provides theoretical insights for hybrid gas HnP-enhanced recovery. These pore-scale results highlight the importance of injection pressure and medium composition during the soaking process in unconventional oil reservoirs.

Study on the Effects of Wettability and Pressure in Shale Matrix Nanopore Imbibition during Shut-in Process by Molecular Dynamics Simulations

Shut-in after fracturing is generally adopted for wells in shale oil reservoirs, and imbibition occurring in matrix nanopores has been proven as an effective way to improve recovery. In this research, a molecular dynamics (MD) simulation was used to investigate the effects of wettability and pressure on nanopore imbibition during shut-in for a typical shale reservoir, Jimsar. The results indicate that the microscopic advancement mechanism of the imbibition front is the competitive adsorption between "interfacial water molecules" at the imbibition front and "adsorbed oil molecules" on the pore wall. The essence of spontaneous imbibition involves the adsorption and aggregation of water molecules onto the hydroxyl groups on the pore wall. The flow characteristics of shale oil suggest that the overall push of the injected water to the oil phase is the main reason for the displacement of adsorbed oil molecules. Thus, shale oil, especially the heavy hydrocarbon component in the adsorbed layer, tends to slip on the walls. However, the weak slip ability of heavy components on the wall surface is an important reason that restricts the displacement efficiency of shale oil during spontaneous imbibition. The effectiveness of spontaneous imbibition is strongly dependent on the hydrophilicity of the matrix pore's wall. The better hydrophilicity of the matrix pore wall facilitates higher levels of adsorption and accumulation of water molecules on the pore wall and requires less time for "interfacial water molecules" to compete with adsorbed oil molecules. During the forced imbibition process, the pressure difference acts on both the bulk oil and the boundary adsorption oil, but mainly on the bulk oil, which leads to the occurrence of wetting hysteresis. Meanwhile, shale oil still existing in the pore always maintains a good, stratified adsorption structure. Because of the wetting hysteresis phenomenon, as the pressure difference increases, the imbibition effect gradually increases, but the actual capillary pressure gradually decreases and there is a loss in the imbibition velocity relative to the theoretical value. Simultaneously, the decline in hydrophilicity further weakens the synergistic effect on the imbibition of the pressure difference because of the more pronounced wetting hysteresis. Thus, selecting an appropriate well pressure enables cost savings and maximizes the utilization of the formation's natural power for enhanced oil recovery (EOR).

Taking a look accurately at the alteration of interfacial asphaltene film exposed to the ionic surfactants as demulsifiers

The water droplets surrounded by a rigid interfacial asphaltene (ASP) film is one of the major setbacks in the petroleum industry. In this study, the properties of the interfacial ASP films around water droplets exposed to ionic surfactants as demulsifier were investigated. According to molecular dynamics (MD) simulation, the anionic surfactants are more effective than the cationic surfactant in the demulsification process since the anionic surfactants have the exact desire to localize not only near the ASP molecules but also near the water molecules. It has been found that it is likely to cause film changes and ruptures. Also, the MD simulation results for the desired surfactant, anionic surfactant, demonstrated that an increase in the surfactant concentration had an adverse effect on the system by hindering the change in the interfacial film. The increase in the temperature along with the enhancement in the adsorption rate of the surfactant results in the better performance of the demulsifier. Taking the MD and quantum results into account, the film deformation is a decisive factor in demulsification. The quantum computation has indicated that the electrostatic interactions play a significant role in selecting the attraction position and adsorption energy of the surfactant molecules.