High-resolution magnetic resonance flow imaging in a model of porous bone-implant interface

Micromotion-induced peri-prosthetic fluid flow around a cementless femoral stem

Micromotion-induced interstitial fluid flow at the bone-implant interface has been proposed to play an important role in aseptic loosening of cementless implants. High fluid velocities are thought to promote aseptic loosening through activation of osteoclasts, shear stress induced control of mesenchymal stem cells differentiation, or transport of molecules. In this study, our objectives were to characterize and quantify micromotion-induced fluid flow around a cementless femoral stem using finite element modeling. With a 2D model of the bone-implant interface and full-factorial design, we first evaluated the relative influence of material properties, and bone-implant micromotion and gap on fluid velocity. Transverse sections around a femoral stem were built from computed tomography images, while boundary conditions were obtained from experimental measurements on the same femur. In a second step, a 3D model was built from the same data-set to estimate the shear stress experienced by cells hosted in the peri-implant tissues. The full-factorial design analysis showed that local micromotion had the most influence on peak fluid velocity at the interface. Remarkable variations in fluid velocity were observed in the macrostructures at the surface of the implant in the 2D transverse sections of the stem. The 3D model predicted peak fluid velocities extending up to 2.2 mm/s in the granulation tissue and to 3.9 mm/s in the trabecular bone. Peak shear stresses on the cells hosted in these tissues ranged from 0.1 to 12.5 Pa. These results offer insight into mechanical stimuli encountered at the bone-implant interface.

Fluid-structure interactions in micro-interlocked regions of the cement-bone interface

Experimental tests and computational modelling were used to explore the fluid dynamics at the trabeculae-cement interlock regions found in the tibial component of total knee replacements. A cement-bone construct of the proximal tibia was created to simulate the immediate post-operative condition. Gap distributions along nine trabeculae-cement regions ranged from 0 to 50.4 μm (mean = 12 μm). Micro-motions ranged from 0.56 to 4.7 μm with a 1 MPa compressive load to the cement. Fluid-structure analysis between the trabeculae and the cement used idealised models with parametric evaluation of loading direction, gap closing fraction (GCF), gap thickness, loading frequency and fluid viscosity. The highest fluid shear stresses (926 Pa) along the trabecular surface were found for conditions with very thin and large GCFs, much larger than reported physiological levels (~1-5 Pa). A second fluid-structure model was created with a provision for bone resorption using a constitutive model with resorption velocity proportional to fluid shear rate. A lower cut-off was used, below which bone resorption would not occur (50 s(-1)). Results showed that there was initially high shear rates (>1000 s(-1)) that diminished after initial trabecular resorption. Resorption continued in high shear rate regions, resulting in a final shape with bone left deep in the cement layer, and is consistent with morphology found in post-mortem retrievals. Small gaps between the trabecular surface and the cement in the immediate post-operative state produce fluid flow conditions that appear to be supra-physiologic; these may cause fluid-induced lysis of trabeculae in the micro-interlock regions.

Use of high-resolution MRI for investigation of fluid flow and global permeability in a material with interconnected porosity

We present a multi-scale experimental approach designed to improve the investigation of both localized and global fluid flow in biomaterials with randomly interconnected porosity. Coralline hydroxyapatite (ProOsteon 500 from Interpore-Cross), having a relatively well-defined porosity, was used as an in vitro model of typical bone architecture. Axial fluid velocity profiles within the pores of a cylindrical hydroxyapatite sample were characterized using high-resolution MRI in conjunction with the measurement of global flow and associated permeability based on the Darcy-type relationship. Assuming Newtonian fluid behaviour, image analysis permitted computation of local porosity, intra-pore fluid shear, and visualization of flow heterogeneity within the sample. These results may benefit applications in biomaterials for the evaluation of factors influencing bony incorporation in porous scaffolds and on porous implant and bone surfaces. Normal and diseased biological tissues are also clinical relevant applications.