Fabrication of calcite blocks from gypsum blocks by compositional transformation based on dissolution-precipitation reactions in sodium carbonate solution

Synergistic Effect of Carbonate Apatite and Autogenous Bone on Osteogenesis

Bone augmentation using artificial bone is an important option in dental defect prostheses. A bone substitute using carbonate apatite (CO₃Ap), an inorganic component of bone, was reported to have promising bone formation and bone replacement ability. However, the osteoinductivity of artificial bone is less than autogenous bone (AB). In this study, CO₃Ap with AB is demonstrated as a clinically effective bone substitute. For in vitro experiments, an osteoclast-like cell (RAW-D) was cultured in the presence of AB, CO₃Ap, or both (Mix), and the number of osteoclasts was evaluated. Osteoblasts were also cultured under the same conditions, and the number of adherent cells was evaluated. For in vivo experiments, a few holes were created in the rat tibia and AB, CO₃Ap, or Mix were added. At 0, 14, and 21 days, the tissue morphology of the wound area was observed, and the thickness of the cortical bone was measured. In vitro, Mix did not increase the number of osteoclasts or osteoblasts. However, in vivo, the rate of bone replacement remarkably increased with Mix on dome-shape. A bone-grafting material combining osteoinductive AB with abundant artificial bone is expected to be clinically easy to use and able to form bone.

Customized Design 3D Printed PLGA/Calcium Sulfate Scaffold Enhances Mechanical and Biological Properties for Bone Regeneration

Polylactic glycolic acid copolymer (PLGA) has been widely used in tissue engineering due to its good biocompatibility and degradation properties. However, the mismatched mechanical and unsatisfactory biological properties of PLGA limit further application in bone tissue engineering. Calcium sulfate (CaSO₄) is one of the most promising bone repair materials due to its non-immunogenicity, well biocompatibility, and excellent bone conductivity. In this study, aiming at the shortcomings of activity-lack and low mechanical of PLGA in bone tissue engineering, customized-designed 3D porous PLGA/CaSO₄ scaffolds were prepared by 3D printing. We first studied the physical properties of PLGA/CaSO₄ scaffolds and the results showed that CaSO₄ improved the mechanical properties of PLGA scaffolds. In vitro experiments showed that PLGA/CaSO₄ scaffold exhibited good biocompatibility. Moreover, the addition of CaSO₄ could significantly improve the migration and osteogenic differentiation of MC3T3-E1 cells in the PLGA/CaSO₄ scaffolds, and the PLGA/CaSO₄ scaffolds made with 20 wt.% CaSO₄ exhibited the best osteogenesis properties. Therefore, calcium sulfate was added to PLGA could lead to customized 3D printed scaffolds for enhanced mechanical properties and biological properties. The customized 3D-printed PLGA/CaSO₄ scaffold shows great potential for precisely repairing irregular load-bearing bone defects.

In vivo bioresorbability and bone formation ability of sintered highly pure calcium carbonate granules

Calcium carbonate-based bone substitutes derived from natural coral exoskeleton (aragonite) are resorbed and remodeled faster than calcium phosphate-based substitutes. However, coral species with structures appropriate for use as bone substitutes are very limited. Therefore, it is important to evaluate potential of artificial calcium carbonate ceramics as a bone substitute. In this study, calcium carbonate granules with various porosities and pore sizes were prepared by sintering a highly pure (>99.98%) calcium carbonate powder (calcite), and their resorption properties and bone formation abilities were examined in vivo for the first time. The sintered calcium carbonate was resorbed faster than β-tricalcium phosphate, which has a similar structure. However, sintered calcium carbonate did not promote new bone formation during long-term implantation. Furthermore, both resorption and new bone formation were affected by the pore structure. The optimal structures of the artificially sintered calcium carbonate bone substitute were also discussed.

Fabrication of porous carbonate apatite granules using microfiber and its histological evaluations in rabbit calvarial bone defects

Carbonate apatite (CO₃ Ap) granules are known to show good osteoconductivity and replaced to new bone. On the other hand, it is well known that a porous structure allows bone tissue to penetrate its pores, and the optimal pore size for bone ingrowth is dependent on the composition and structure of the scaffold material. Therefore, the aim of this study was to fabricate various porous CO₃ Ap granules through a two-step dissolution-precipitation reaction using CaSO₄ as a precursor and 30-, 50-, 120-, and 205-μm diameter microfibers as porogen and to find the optimal pore size of CO₃ Ap. Porous CO₃ Ap granules were successfully fabricated with pore size 8.2-18.7% smaller than the size of the original fiber porogen. Two weeks after the reconstruction of rabbit calvarial bone defects using porous CO₃ Ap granules, the largest amount of mature bone was seen to be formed inside the pores of CO₃ Ap (120) [porous CO₃ Ap granules made using 120-μm microfiber] followed by CO₃ Ap (50) and CO₃ Ap (30). At 4 and 8 weeks, no statistically significant difference was observed based on the pore size, even though largest amount of mature bone was formed in case of CO₃ Ap (120). It is concluded, therefore, that the optimal pore size of the CO₃ Ap is that of CO₃ Ap (120), which is 85 μm.