Diatomite reinforced chitosan composite membrane as potential scaffold for guided bone regeneration

Osteoblast responsive biosilica-enriched gelatin microfibrillar microenvironments

Engineering of scaffolds for bone regeneration is often inspired by the native extracellular matrix mimicking its composite fibrous structure. In the present study, we used low loadings of diatomite earth (DE) biosilica to improve the bone regeneration potential of gelatin electrospun fibrillar microenvironments. We explored the effect of increasing the DE content from 1 % to 3 % and 5 %, respectively, on the physico-chemical properties of the fibrous scaffolds denoted FG_DE1, FG_DE3, FG_DE5, regarding the aqueous media affinity, stability under simulated physiological conditions, morphology characteristics, and local mechanical properties at the surface. The presence of biosilica generated composite structures with lower swelling degrees and higher stiffness when compared to gelatin fibers. Increasing DE content led to higher Young modulus, while the stability of the protein matrix in PBS, at 37 °C, over 21 was significantly decreased by the presence of diatomite loadings. The best preosteoblast response was obtained for FG_DE3, with enhanced mineralization during the osteogenic differentiation when compared to the control sample without diatomite. 5 % DE in FG_DE5 proved to negatively influence cells' metabolic activity and morphology. Hence, the obtained composite microfibrillar scaffolds might find application as osteoblast-responsive materials for bone tissue engineering.

Design of chemobrionic and biochemobrionic scaffolds for bone tissue engineering

Chemobrionic systems have attracted great attention in material science for development of novel biomimetic materials. This study aims to design a new bioactive material by integrating biosilica into chemobrionic structure, which will be called biochemobrionic, and to comparatively investigate the use of both chemobrionic and biochemobrionic materials as bone scaffolds. Biosilica, isolated from Amphora sp. diatom, was integrated into chemobrionic structure, and a comprehensive set of analysis was conducted to evaluate their morphological, chemical, mechanical, thermal, and biodegradation properties. Then, the effects of both scaffolds on cell biocompatibility and osteogenic differentiation capacity were assessed. Cells attached to the scaffolds, spread out, and covered the entire surface, indicating the absence of cytotoxicity. Biochemobrionic scaffold exhibited a higher level of mineralization and bone formation than the chemobrionic structure due to the osteogenic activity of biosilica. These results present a comprehensive and pioneering understanding of the potential of (bio)chemobrionics for bone regeneration.

Carbene-mediated gelatin and hyaluronic acid hydrogel paints with ultra adhesive ability for arthroscopic cartilage repair

In articular cartilage defect, particularly in arthroscopy, regenerative hydrogels are urgently needed. It should be able to firmly adhere to the cartilage tissue and maintain sufficient mechanical strength to withstand approximately 10 kPa of arthroscopic hydraulic flushing. In this study, we report a carbene-mediated ultra adhesive hybrid hydrogel paints for arthroscopic cartilage repair, which combined the photo initiation of double crosslinking system with the addition of diatomite, as a further reinforcing agent and biological inorganic substances. The double network consisting of ultraviolet initiated polymerization of hyaluronic acid methacrylate (HAMA) and carbene insertion chemistry of diazirine-grafted gelatin (GelDA) formed an ultra-strong adhesive hydrogel paint (H2G5DE). Diatomite helped the H2G5DE hydrogel paint firmly adhere to the cartilage defect, withstanding nearly 100 kPa of hydraulic pressure, almost 10 times that in clinical arthroscopy. Furthermore, the H2G5DE hydrogel supported cell growth, proliferation, and migration, thus successfully repairing cartilage defects. Overall, this study demonstrates a proof-of-concept of ultra-adhesive polysaccharide hydrogel paints, which can firmly adhere to the articular cartilage defects, can resist continuous hydraulic pressure, can promote effective cartilage regeneration, and is very suitable for minimally invasive arthroscopy.

Diatom-guided bone healing via a hybrid natural scaffold

Bone tissue engineering (BTE) involves the design of three-dimensional (3D) scaffolds that aim to address current challenges of bone defect healing, such as limited donor availability, disease transmission risks, and the necessity for multiple invasive surgeries. Scaffolds can mimic natural bone structure to accelerate the mechanisms involved in the healing process. Herein, a crosslinked combination of biopolymers, including gelatin (GEL), chitosan (CS), and hyaluronic acid (HA), loaded with diatom (Di) and β-sitosterol (BS), is used to produce GCH-Di-S scaffold by freeze-drying method. The GCH scaffold possesses a uniform structure, is biodegradable and biocompatible, and exhibits high porosity and interconnected pores, all required for effective bone repair. The incorporation of Di within the scaffold contributes to the adjustment of porosity and degradation, as well as effectively enhancing the mechanical property and biomineralization. In vivo studies have confirmed the safety of the scaffold and its potential to stimulate the creation of new bone tissue. This is achieved by providing an osteoconductive platform for cell attachment, prompting calcification, and augmenting the proliferation of osteoblasts, which further contributes to angiogenesis and anti-inflammatory effects of BS.

Biomimetic Diatom Biosilica and Its Potential for Biomedical Applications and Prospects: A Review

Diatom biosilica is an important natural source of porous silica, with three-dimensional ordered and nanopatterned structures referred to as frustules. The unique features of diatom frustules, such as their high specific surface area, thermal stability, biocompatibility, and adaptable surface chemistry, render diatoms valuable materials for high value-added applications. These attributes make diatoms an exceptional cost-effective raw material for industrial use. The functionalization of diatom biosilica surface improves its biophysical properties and increases the potential applications. This review focuses on the potential uses of diatom biosilica including traditional approaches and recent progress in biomedical applications. Not only well-studied drug delivery systems but also promising uses on bone regeneration and wound healing are covered. Furthermore, considerable aspects and possible future directions for the use of diatom biosilica materials are proposed to develop biomedical applications and merit further exploration.

Chitosan-polyvinyl alcohol-diatomite hydrogel removes methylene blue from water

Dye pollution in the aquatic environment can harm ecosystems and human health. Here, we developed a new green adsorbent by applying an improved drying process. Diatomite was embedded in a network structure formed between chitosan and polyvinyl alcohol without using any crosslinking agent to prepare chitosan-polyvinyl alcohol-diatomite hydrogel beads through alkali solidification. The beads were tested for removing a cationic dye (methylene blue (MB)) from water. The structure of the adsorbent beads was analysed using scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Fourier-transform infrared spectroscopy. The adsorption capacity was investigated, and the results indicated excellent MB adsorption properties. The adsorbents had a rough surface and high swelling capacity of 66.9 g/g. The maximum MB adsorption capacity was 414.70 mg/g, and the adsorption followed the Freundlich isothermal and quasi-second-order kinetic models. The adsorption was an endothermic spontaneous process governed by both intra-particle and external diffusion processes. The proposed adsorption mechanisms involved hydrogen bonding and electrostatic interactions. These adsorbent beads have considerable application potentials owing to their high adsorption capacity, green composition, and non-polluting nature.

Root-shaped antibacterial alginate sponges with enhanced hemostasis and osteogenesis for the prevention of dry socket

Tooth extraction commonly causes uncontrolled bleeding, loss of blood clots, and bacterial infection, leading to the dry socket and bone resorption. Thus, it is highly attractive to design a bio-multifunctional scaffold with outstanding antimicrobial, hemostatic, and osteogenic performances for avoiding dry sockets in clinical applications. Herein, alginate (AG)/quaternized chitosan (Qch)/diatomite (Di) sponges were fabricated via electrostatic interaction, Ca²⁺ cross-linking, as well as lyophilization methods. The composite sponges are facilely made into the shape of the tooth root, which could be well integrated into the alveolar fossa. The sponge shows a highly interconnected and hierarchical porous structure at the macro/micro/nano levels. The prepared sponges also possess enhanced hemostatic and antibacterial abilities. Moreover, in vitro cellular assessment indicates that the developed sponges have favorable cytocompatibility and significantly facilitate osteogenesis by upregulating the formation of alkaline phosphatase and calcium nodules. The designed bio-multifunctional sponges display great potential for trauma treatment after tooth extraction.

Synthesis and Evaluation of a Chitosan–Silica-Based Bone Substitute for Tissue Engineering

Bone defects have prompted the development of biomaterial-based bone substitutes for restoring the affected tissue completely. Although many biomaterials have been designed and evaluated, the combination of properties required in a biomaterial for bone tissue engineering still poses a challenge. In this study, a chitosan–silica-based biocomposite was synthetized, and its physicochemical characteristics and biocompatibility were characterized, with the aim of exploring the advantages and drawbacks of its use in bone tissue engineering. Dynamic light scattering measurements showed that the mean hydrodynamic size of solid silica particles (Sol-Si) was 482 ± 3 nm. Scanning electron microscopy of the biocomposite showed that Sol-Si were homogenously distributed within the chitosan (CS) matrix. The biocomposite swelled rapidly and was observed to have no cytotoxic effect on the [3T3] cell line within 24 h. Biocompatibility was also analyzed in vivo 14 days post-implant using a murine experimental model (Wistar rats). The biocomposite was implanted in the medullary compartment of both tibiae (n = 12). Histologically, no acute inflammatory infiltrate or multinucleated giant cells associated to the biocomposite were observed, indicating good biocompatibility. At the tissue–biocomposite interface, there was new formation of woven bone tissue in close contact with the biocomposite surface (osseointegration). The new bone formation may be attributed to the action of silica. Free silica particles originating from the biocomposite were observed at the tissue–biocomposite interface. According to our results, the biocomposite may act as a template for cellular interactions and extracellular matrix formation, providing a structural support for new bone tissue formation. The CS/Sol-Si biocomposite may act as a Si reservoir, promoting new bone formation. A scaffold with these properties is essential for cell differentiation and filling a bone defect.

3D Natural Mesoporous Biosilica-Embedded Polysulfone Made Ultrafiltration Membranes for Application in Separation Technology

Diatoms are the most abundant photosynthetic microalgae found in all aquatic habitats. In the extant study, the spent biomass (after lipid extraction) of the centric marine diatom Thalassiosira lundiana CSIRCSMCRI 001 was subjected to acid digestion for the extraction of micro composite inorganic biosilica. Then, the resulting three-dimensional mesoporous biosilica material (diatomite) was used as a filler in polysulfone (PSF) membrane preparation by phase inversion. The fabricated PSF/diatomite composite membranes were characterized by SEM-EDX, TGA, and ATR-IR, and their performances were evaluated. The number of pores and pore size were increased on the membrane surface with increased diatomite in the composite membranes as compared to the control. The diatomite composite membranes had high hydrophilicity and thermal stability, lower surface roughness, and excellent water permeability. Membranes with high % diatomite, i.e., PSF/Dia_0.5, had a maximum water flux of 806.8 LMH (Liter/m²/h) at 20 psi operating pressure. High-diatomite content membranes also exhibited the highest rejection of BSA protein (98.5%) and rhodamine 6G (94.8%). Similarly, in biomedical rejection tests, the PSF/Dia_0.5 membrane exhibited a maximum rejection of ampicillin (75.84%) and neomycin (85.88%) at 20 Psi pressure. In conclusion, the mesoporous inorganic biosilica material was extracted from spent biomass of diatom and successfully used in filtration techniques. The results of this study could enhance the application of natural biogenic porous silica materials in wastewater treatment for water recycling.

Facile Preparation of Chitosan-Based Composite Film with Good Mechanical Strength and Flame Retardancy

To improve on the poor strength and flame retardancy of a chitosan (CS)-based functional film, cellulose nanofiber (CNF) was taken as the reinforced material and both ammonium polyphosphate (APP) and branched polyethyleneimine (BPEI) as the flame-retardant additives in the CS matrix to prepare the CS/CNF/APP/BPEI composite film by simple drying. The resulting composite film showed good mechanical strength, with a tensile strength reaching 71.84 Mpa due to the high flexibility of CNF and the combination of CS, CNF and BPEI through strong hydrogen bonding interactions. The flame retardant-performance of the composite film greatly enhanced the limit oxygen index (LOI), up to 32.7% from 27.6% for the pure film, and the PHRR intensity decreased to 28.87 W/g from 39.38% in the micro-scale combustion calorimetry (MCC) test due to the ability of BPEI to stimulate the decomposition of APP, releasing non-flammable gases such as CO₂, N₂, NH₃, etc., and forming a protective phosphating layer to block the entry of O₂. Based on the good flame retardancy, mechanical strength and transparency, the CS/CNF/APP/BPEI composite film has a great potential for future applications.

Asymmetric resorbable-based dental barrier membrane for periodontal guided tissue regeneration and guided bone regeneration: A review

Guided tissue regeneration (GTR) and guided bone regeneration (GBR) are two common dental regenerative treatments targeted at reconstructing damaged periodontal tissue and bone caused by periodontitis. During GTR/GBR treatment, a barrier membrane is placed in the interface between the soft tissue and the periodontal defect to inhibit soft tissue ingrowth and creating a space for the infiltration of slow-growing bone cells into the defect site. Recently, asymmetric resorbable-based barrier membrane has received a considerable attention as a new generation of GTR/GBR membrane. Despite numerous literatures about asymmetric-based membrane that had been published, there is lacks comprehensive review on asymmetric barrier membrane that particularly highlight the importance of membrane structure for periodontal regeneration. In this review, we systematically cover the latest development and advancement of various kinds of asymmetric barrier membranes used in periodontal GTR/GBR application. Herein, the ideal requirements for constructing a barrier membrane as well as the rationale behind the asymmetric design, are firstly presented. Various innovative methods used in fabricating asymmetric barrier membrane are being further discussed. Subsequently, the application and evaluation of various types of asymmetric barrier membrane used for GTR/GBR are compiled and extensively reviewed based on the recent literatures reported. Based on the existing gap in this field, the future research directions of asymmetric resorbable-based barrier membrane such as its combination potential with bone grafts, are also presented.

Biomimetic development of chitosan and sodium alginate-based nanocomposites contains zirconia for tissue engineering applications

Nanostructured materials possess unique structural and functional properties that play a crucial position in tissue engineering applications. Present investigation is aimed to synthesize chitosan-sodium alginate (CS) nanocomposite using hydrothermally prepared zirconia nanoparticles. In this, three different weight percentages of (0.5, 1, and 1.5) zirconia nanoparticles are utilized for the preparation of biomimetic nanocomposite scaffolds (CSZ) employing 4 wt% of CS by a solvent casting technique. Physico-chemical and thermal behavior of the prepared nanoparticles and their CSZ scaffolds are comprehensively characterized. Bioactivity of the prepared zirconia nanoparticles and CSZ scaffolds are explored in terms of in vitro biocompatibility, protein absorption in simulated body fluid (SBF), and phosphate buffered saline (PBS). Agar disc diffusion method is employed to identify the antibacterial property against Staphylococcus aureus and Escherichia coli. In vitro cytotoxicity of zirconia nanoparticles and CSZ scaffolds is identified against human urothelial carcinoma (UC6) and osteosarcoma (MG-63) cells. These studies explore that zirconia nanoparticles are suitable for biomedical applications while it is interacted with chitosan and sodium alginate (CS) due to their promising biocompatibility. Biomimetically obtained chitosan/sodium alginate scaffold contain 1 wt% zirconia nanoparticles show higher biocompatibility amenable for tissue engineering applications.

Development of an Insulin Nano-Delivery System through Buccal Administration

AIM

To develop a new nano-delivery system for insulin buccal administration.

BACKGROUND

Biodegradable polymeric nanoparticles (PNPs) had viewed countless breakthroughs in drug delivery systems. The main objective of PNPs application in delivering and carrying different promising drugs is to make sure that the drugs being delivered to their action sites. As a result maximizing the desired effect and overcoming their limitations and drawbacks.

OBJECTIVES

The main goals of this study were to produce an insulin consumable nano-delivery system for buccal administration and enhance the mucoadhesive effect in sustaining insulin release.

METHODS

Water in oil in water (W-O-W) microemulsion solvent evaporation technique was used for the preparation of nanoparticles consisting from positively charged poly (D, L-lactide-co-glycolide) coated with chitosan and loaded with insulin. Later, a consumable buccal film was prepared by the spin coating method and loaded with the previously prepared nanoparticles.

RESULTS

The newly prepared nanoparticle was assessed in terms of size, charge and surface morphology using a Scanning Electron Microscope (SEM), zeta potential, Atomic Force Microscope (AFM), and Fourier Transform Infra-red (FTIR) spectroscopy. An in-vitro investigation of the insulin release, from nanoparticles and buccal film, demonstrated controlled as well as sustained delivery over 6 hrs. The cumulative insulin release decreased to about (28.9%) with buccal film in comparing with the nanoparticle (50 %).

CONCLUSION

The buccal film added another barrier for insulin release. Therefore, the release was sustained.

Understanding the effects of copolymerized cellulose nanofibers and diatomite nanocomposite on blend chitosan films

Chitosan films lack various important physicochemical properties and need to be supplemented with reinforcing agents to bridge the gap. Herein, we have produced chitosan composite films supplemented with copolymerized (with polyacrylonitrile monomers) cellulose nanofibers and diatomite nanocomposite at different concentrations. The incorporation of CNFs and diatomite enhanced the physicochemical properties of the films. The mechanical characteristics and hydrophobicity of the films were observed to be improved after incorporating the copolymerized CNFs/diatomite composite at different concentrations (CNFs: 1%, 2% and 5%; diatomite: 10% and 30%). The antioxidant activity gradually increased with an increasing concentration (1-5% and 10-30%) of copolymerized CNFs/diatomite composite in the chitosan matrix. Moreover, the water solubility decreased from 30% for chitosan control film (CH-0) to 21.06% for films containing 30% diatomite and 5% CNFs (CNFs-D30-5). The scanning electron micrographs showed an overall uniform distribution of copolymerized CNFs/diatomite composite in the chitosan matrix with punctual agglomerations.

Novel cell sources for bone regeneration

A plethora of both acute and chronic conditions, including traumatic, degenerative, malignant, or congenital disorders, commonly induce bone disorders often associated with severe persisting pain and limited mobility. Over 1 million surgical procedures involving bone excision, bone grafting, and fracture repair are performed each year in the U.S. alone, resulting in immense levels of public health challenges and corresponding financial burdens. Unfortunately, the innate self-healing capacity of bone is often inadequate for larger defects over a critical size. Moreover, as direct transplantation of committed osteoblasts is hindered by deficient cell availability, limited cell spreading, and poor survivability, an urgent need for novel cell sources for bone regeneration is concurrent. Thanks to the development in stem cell biology and cell reprogramming technology, many multipotent and pluripotent cells that manifest promising osteogenic potential are considered the regenerative remedy for bone defects. Considering these cells' investigation is still in its relative infancy, each of them offers their own particular challenges that must be conquered before the large-scale clinical application.

Evolution of drug-eluting biomedical implants for sustained drug delivery

In the field of drug delivery, the most commonly used treatments have traditionally been systemically delivered using oral or intravenous administration. The problems associated with this type of delivery is that the drug concentration is controlled by first pass metabolism, and therefore may not always remain within the therapeutic window. Implantable drug delivery systems (IDDSs) are an excellent alternative to traditional delivery because they offer the ability to precisely control the drug release, deliver drugs locally to the target tissue, and avoid the toxic side effects often experienced with systemic administration. Since the creation of the first FDA-approved IDDS in 1990, there has been a surge in research devoted to fabricating and testing novel IDDS formulations. The versatility of these systems is evident when looking at the various biomedical applications that utilize IDDSs. This review provides an overview of the history of IDDSs, with examples of the different types of IDDS formulations, as well as looking at current and future biomedical applications for such systems. Though there are still obstacles that need to be overcome, ever-emerging new technologies are making the manufacturing of IDDSs a rewarding therapeutic endeavor with potential for further improvements.

The preparation of chitosan membrane improved with nanoparticles based on unsaturated fatty acid for using in cancer-related infections

This study includes the design of a chitosan membrane decorated with unsaturated fatty acid–based carrier system for cancer treatment and antibacterial application. For this, polystyrene-graft-polyoleic acid-graft-polyethylene glycol was prepared by free radical polymerization and characterized. Nanoparticles and caffeic acid–loaded nanoparticles were prepared by solvent evaporation technique and optimized. The short-term stability of nanoparticles was investigated at 4°C. Drug encapsulation and loading efficiency were evaluated. The chitosan membrane and caffeic acid–loaded nanoparticles embedded into chitosan membrane were fabricated. The caffeic acid loaded nanoparticles embedded into chitosan membrane showed controlled release. The mechanical properties of all samples were investigated. The caffeic acid–loaded nanoparticles embedded into chitosan membranes indicated excellent antibacterial properties against the Escherichia coli and Staphylococcus aureus. The anticancer activity of all the samples was evaluated against SaOS-2 human primary osteogenic sarcoma and MC3T3-E1 pre-osteoblast cell lines by 3-[4,5-dimethylthiazol-2-yl]-2,5 diphenyl tetrazolium bromide assay, the flow cytometry and double staining methods. As a result, the designed carrier system showed great potential to cancer-associated infections treatment in bone cancer cases.

Fabrication of Green Diatomite/Chitosan-Based Hybrid Foams with Dye Sorption Capacity

The latest tendency of the scientific community regards the development of different classes of green materials able to solve pollution problems caused by industrial and human activity. In this paper, chitosan and diatomite were used to produce a broad-spectrum hybrid adsorbent, either in powder or in monolithic form for environmental pollutant removal. Diatomite-chitosan-based powders and porous diatomite-chitosan hybrids were prepared and characterized by chemical-physical, thermal and morphological analysis. Moreover, their adsorbent capacity towards anionic dye (Indigo Carmine) was also evaluated. Obtained data showed that chitosan improves the adsorption capacity of both systems, increasing the uptake of dye in both diatomite-chitosan systems.

Gaseous sulfur trioxide induced controllable sulfonation promoting biomineralization and osseointegration of polyetheretherketone implants

Fabricating a desired porous structure on the surface of biomedical polyetheretherketone (PEEK) implants for enhancing biological functions is crucial and difficult due to its inherent chemical inertness. In this study, a porous surface of PEEK implants was fabricated by controllable sulfonation using gaseous sulfur trioxide (SO₃) for different time (5, 15, 30, 60 and 90 min). Micro-topological structure was generated on the surface of sulfonated PEEK implants preserving original mechanical properties. The protein absorption capacity and apatite forming ability was thus improved by the morphological and elemental change with higher degree of sulfonation. In combination of the appropriate micromorphology and bioactive sulfonate components, the cell adhesion, migration, proliferation and extracellular matrix secretion were obviously enhanced by the SPEEK-15 samples which were sulfonated for 15 min. Finding from this study revealed that controllable sulfonation by gaseous SO₃ would be an extraordinarily strategy for improving osseointegration of PEEK implants by adjusting the microstructure and chemical composition while maintaining excellent mechanical properties.

Design, synthesis, characterization and biological evaluation of Thieno[2,3-b]pyridines-chitosan nanocomposites as drug delivery systems for colon targeting

Thieno[2,3-b]pyridine derivatives DATP_a-c have been synthesized based on Thorpe-Ziegler Cyclization. The reaction of arylidene malononitrile derivatives (I_a-c) with thiocyanoacetamide (II) in basic medium (piperidine) followed by alkylation using ethyl chloroacetate and finally, cyclization in sodium ethoxide yielded DATP_a-c. Thieno[2,3-b]pyridine-chitosan nanocomposites CS-DATP_a-c were prepared from the DATP_a-c and CS nanoparticles using sodium tripolyphosphate (TPP). CS-DATP_a-c nanocomposites were characterized using FTIR, TEM and XRD techniques and showed a relatively narrow size distribution of monodispersed nanoparticles with the average size of 14-78 nm. The in vitro release studies of CS-DAΤP_a-c nanocomposites were investigated and showed that the drug release rate is pH-dependent and the trend is as follows: basic > neutral > acidic. The faster release rate in basic medium effectively prolongs drug delivery in gastric pH. Additionally, the antibacterial investigation showed that DATP_a-c and CS-DATP_a-c nanocomposites exhibited antibacterial activity against both Gram-positive and Gram-negative bacteria but CS-DATP_a-c nanocomposites showed much higher antibacterial activity compared to the DATP_a-c, which in agreement with the particle size measurements as DATP_a-c are in the bulky structure whereas, CS-DATP_a-c are in the nanostructure. The results may have applications of drug design for colon targeting.

Biomimetic TiO2-chitosan/sodium alginate blended nanocomposite scaffolds for tissue engineering applications

The study is aimed to synthesize potent metal oxide based biomimetic nanocomposites to overcome the risk associated with artificial bone tissue engineering. High purity TiO₂ nanoparticles are synthesized via hydrothermal route. A biomimetic nanocomposite scaffolds containing chitosan-sodium alginate (4: 4) blended with three different (0.5, 1, and 1.5 wt%) concentrations of hydrothermally synthesized TiO₂ nanoparticles are obtained by solvent casting technique. The physico-chemical and thermal degradation properties of as-synthesized TiO₂ nanoparticles and their nanocomposite scaffolds are analyzed. In-vitro cytotoxicity and biocompatibility of the prepared TiO₂ nanoparticles and nanocomposites are tested against human bladder tumor (UC6) and osteosarcoma (MG-63) cell lines. Antibacterial property is tested against Escherichia coli and Staphylococcus aureus. These studies reveal that TiO₂ nanoparticles and polymeric nanocomposites contain good physico-chemical and mechanical properties for enhanced in-vitro biocompatibility suitable for biomedical applications. Biomimetically prepared chitosan-sodium alginate scaffold containing TiO₂ nanoparticles (1 wt%) is found to exhibit superior biocompatibility for bone tissue engineering applications.

Degradable poly(ester-ether) urethanes of improved surface calcium deposition developed as novel biomaterials

Bones, which are considered as hard tissues, work as scaffold for human body. They provide physical support for muscles and protect intestinal organs. Percentage of hard tissues in human body depends on age, weight, and gender. Human skeleton consists of 206 connected bones. Therefore, it is natural that the hard-tissue damage such as fractures, osteoporosis, and congenital lack of bone may appear. The innovative way of bone healing is an application of so-called tissue scaffolds. There are many synthetic polymers used in this field, but polyurethanes play a great role in this field. It is due to the possibility to control their degradation rate and to tune their surface to improve the calcification process, required for proper bone regeneration. In this article, we described the fabrication of degradable poly(ester-ether)urethane materials, having different hard-segment content (28% or 47%). PEEURs-28HS and PEEURs-47HS materials were obtained by two-step polymerization method and characterized by mechanical properties, ability to undergo oxidative degradation and surface calcification. Performed studies indicated that the PEEURs-28HS material possessed suitable properties to be proposed as a material for possible application in the bone tissue engineering.

Bioactive diatomite and POSS silica cage reinforced chitosan/Na-carboxymethyl cellulose polyelectrolyte scaffolds for hard tissue regeneration

Recently, natural polymers are reinforced with silica particles for hard tissue engineering applications to induce bone regeneration. In this study, as two novel bioactive agents, effects of diatomite and polyhedral oligomeric silsesquioxanes (POSS) on chitosan (CS)/Na-carboxymethylcellulose (Na-CMC) polymer blend scaffolds are examined. In addition, the effect of silica reinforcements was compared with Si-substituted nano-hydroxyapatite (Si-Hap) particles. The morphology, physical and chemical structures of the scaffolds were characterized with SEM, liquid displacement, FT-IR, mechanical analysis, swelling and degradation studies. The particle size and the crystal structure of diatomite, POSS and Si-Hap particles were determined with DLS and XRD analyses. In vitro studies were performed to figure out the cytotoxicity, proliferation, ALP activity, osteocalcin production and biomineralization to demonstrate the promising use of natural silica particles in bone regeneration. Freeze-dried scaffolds showed 190-307 μm pore size range and 61-70% porosity. Both inorganic reinforcements increased the mechanical strength, enhanced the water uptake capacity and fastened the degradation rate. The nanocomposite scaffolds did not show any cytotoxic effect and enhanced the surface mineralization in osteogenic medium. Thus, diatomite and POSS cage structures can be potential reinforcements for nanocomposite design in hard tissue engineering applications.

Effect of Calcium Precursor on the Bioactivity and Biocompatibility of Sol-Gel-Derived Glasses

This study investigated the impact of different calcium reagents on the morphology, composition, bioactivity and biocompatibility of two-component (CaO-SiO₂) glasses produced by the Stöber process with respect to their potential application in guided tissue regeneration (GTR) membranes for periodontal repair. The properties of the binary glasses were compared with those of pure silica Stöber particles. The direct addition of calcium chloride (CC), calcium nitrate (CN), calcium methoxide (CM) or calcium ethoxide (CE) at 5 mol % with respect to tetraethyl orthosilicate in the reagent mixture gave rise to textured, micron-sized aggregates rather than monodispersed ~500 nm spheres obtained from the pure silica Stöber synthesis. The broadening of the Si-O-Si band at ~1100 cm-1 in the infrared spectra of the calcium-doped glasses indicated that the silicate network was depolymerised by the incorporation of Ca2+ ions and energy dispersive X-ray analysis revealed that, in all cases, the Ca:Si ratios were significantly lower than the nominal value of 0.05. The distribution of Ca2+ ions was also found to be highly inhomogeneous in the methoxide-derived glass. All samples released soluble silica species on exposure to simulated body fluid, although only calcium-doped glasses exhibited in vitro bioactivity via the formation of hydroxyapatite. The biocompatibilities of model chitosan-glass GTR membranes were assessed using human MG63 osteosarcoma cells and were found to be of the order: CN < pure silica ≈ CC << CM ≈ CE. Calcium nitrate is the most commonly reported precursor for the sol-gel synthesis of bioactive glasses; however, the incomplete removal of nitrate ions during washing compromised the cytocompatibility of the resulting glass. The superior bioactivity and biocompatibility of the alkoxide-derived glasses is attributed to their ease of dissolution and lack of residual toxic anions. Overall, calcium ethoxide was found to be the preferred precursor with respect to extent of calcium-incorporation, homogeneity, bioactivity and biocompatibility.

Influence of the physicochemical characteristics of diatom frustules on hemorrhage control

Diatom frustules are good resources for hemostasis agent production.

Dual functional electrospun core-shell nanofibers for anti-infective guided bone regeneration membranes

In clinic infection is the paramount cause for failure of guided bone regeneration (GBR) membranes. Therefore, it is crucial to develop anti-infective GBR membranes for clinical bone repair application. In this research, we successfully prepared electrospun core-shell nanofibers loaded with metronidazole (MNA) and nano-hydroxyapatites (nHA), which could be employed for anti-infective GBR membranes due to the achievement of dual functions with enhanced osteogenesis and slow MNA release. The nanofiber shell was composed of polycaprolactone and nHA, whilst the nanofiber core was gelatin and MNA. The MNA release and cell proliferation experiments showed that compared with directly MNA-loaded nanofibers, the core-shell nanofibers possessed slower MNA release profile, which resulted in the decrease in cytotoxicity of MNA to bone mesenchymal stem cells. The osteogenic measurements demonstrated that the core-shell nanofibers could enhance bone formation. Additionally, the anti-bacterial experiments indicated that the core-shell nanofibers could prevent colonization of anaerobic bacteria. In summary, the results in the present study revealed the potential of the core-shell electrospun nanofibers with dual functions of enhanced osteogenesis and anti-infection for optimal clinical application as GBR membranes.

Current development of biodegradable polymeric materials for biomedical applications

In the last half-century, the development of biodegradable polymeric materials for biomedical applications has advanced significantly. Biodegradable polymeric materials are favored in the development of therapeutic devices, including temporary implants and three-dimensional scaffolds for tissue engineering. Further advancements have occurred in the utilization of biodegradable polymeric materials for pharmacological applications such as delivery vehicles for controlled/sustained drug release. These applications require particular physicochemical, biological, and degradation properties of the materials to deliver effective therapy. As a result, a wide range of natural or synthetic polymers able to undergo hydrolytic or enzymatic degradation is being studied for biomedical applications. This review outlines the current development of biodegradable natural and synthetic polymeric materials for various biomedical applications, including tissue engineering, temporary implants, wound healing, and drug delivery.

Bioactive Sr(II)/Chitosan/Poly(ε-caprolactone) Scaffolds for Craniofacial Tissue Regeneration. In Vitro and In Vivo Behavior

In craniofacial tissue regeneration, the current gold standard treatment is autologous bone grafting, however, it presents some disadvantages. Although new alternatives have emerged there is still an urgent demand of biodegradable scaffolds to act as extracellular matrix in the regeneration process. A potentially useful element in bone regeneration is strontium. It is known to promote stimulation of osteoblasts while inhibiting osteoclasts resorption, leading to neoformed bone. The present paper reports the preparation and characterization of strontium (Sr) containing hybrid scaffolds formed by a matrix of ionically cross-linked chitosan and microparticles of poly(ε-caprolactone) (PCL). These scaffolds of relatively facile fabrication were seeded with osteoblast-like cells (MG-63) and human bone marrow mesenchymal stem cells (hBMSCs) for application in craniofacial tissue regeneration. Membrane scaffolds were prepared using chitosan:PCL ratios of 1:2 and 1:1 and 5 wt % Sr salts. Characterization was performed addressing physico-chemical properties, swelling behavior, in vitro biological performance and in vivo biocompatibility. Overall, the composition, microstructure and swelling degree (≈245%) of scaffolds combine with the adequate dimensional stability, lack of toxicity, osteogenic activity in MG-63 cells and hBMSCs, along with the in vivo biocompatibility in rats allow considering this system as a promising biomaterial for the treatment of craniofacial tissue regeneration.