Challenges in modeling total knee arthroplasty and total hip replacement

Biomechanics and finite element analysis comparing posterior T-plates with LCP for fixation of posterolateral tibial plate fractures

Objective: The treatment for posterolateral tibial plateau fractures (PTPF) have been subjects of controversy. We conducted a study to improve the fixation of PTPF through a lateral approach. Methods: We utilized 40 synthetic tibias and categorized the fracture models into five groups based on the locking compression plate (LCP) and T-distal radius plate (TPP) via various forms of fixation with screws through the posterolateral (PL) fracture fragments. I: Two-screw fixation using two locking screws (LPTL). Ⅱ: Two-screw fixation with both variable angle locking screws (LPTV). Ⅲ: One-screw fixation with one locking screw (LPOL). Ⅳ: One-screw fixation with one locking screw and two anteroposterior lag screws (LPOLTL). Ⅴ: a distal radius plate with three locking screws (TPP). Biomechanical tests were conducted to observe the axial compression displacement of the PL fracture fragments at force levels of 250 N, 500 N, and 750 N, as well as to determine the failure load and the axial stiffness for each respective group. Results: Under a 750 N load condition, the displacements within the five experimental groups exhibited the following trend: Ⅴ < Ⅱ < Ⅰ< Ⅳ < Ⅲ. However, there were no significant differences between Group V and Group II, Group I and Group IV (p > 0.05), and only Group Ⅲ demonstrated a displacement exceeding 3 mm. The failure load and the axial stiffness exhibited the same trend. Conversely, statistical significance was identified among the remaining group compared with Group Ⅲ (p < 0.05). Regarding the finite element analysis, the maximum displacements for the five models under the load of 750 N exhibited the following trend: Ⅴ < Ⅱ < Ⅰ< Ⅳ < Ⅲ. The following trends were observed in maximum von Mises stresses for these models under the load of 750 N: Ⅴ < Ⅱ < Ⅳ< Ⅰ < Ⅲ. Conclusion: It is crucial to address the inadequate mechanical strength associated with single screw fixation of LCP for fixing PL fractures in a clinical setting. The biomechanical strength of two-screw fixation surpasses that of single-screw fixation. Introducing variable-angle screws can further enhance the fixation range. Furthermore, the addition of two lag screws threaded from anterior to posterior can compensate the mechanical stability, when PL fracture is fixed with single screw in clinic.

Novel screw-cable integrated system(SCIS) for minimally invasive treatment of patella transverse fractures: a finite element analysis

BACKGROUND

The most recommended method for treating transverse patella fractures is modified tension band wiring (MTBW). However, the optimal instrument for use with MTBW is still undetermined. Hence, we aimed to design a novel screw-cable integrated system (SCIS) and compare its biomechanical characteristics with Kirschner-wire, SCIS, and Cable-Pin systems in treating transverse patellar fracture.

METHODS

A finite-element (FE) model of transverse patella fracture was created. The fracture model was fixed with either K-wire, SCIS, or Cable-pin. Different tension force loading (400 N and 800 N), direction(0° and 45°), and screw or K-wire depth(5 mm and 10 mm) were set. The maximum displacement of the fragment and maximum gap opening were measured by using FE analysis.

RESULTS

Compared with the K-wire and Cable-pin system, SCIS increased the stability of the fractured patella by reducing fragment displacement and gap opening. Under 400 N loading in the direction 45°, SCIS with screw placing at 5-mm depth reduced the maximum fragment displacement (0.43 mm) by 49.62% and 26%, respectively, compared with the K-wire (0.22 mm) and Cable-pin (0. 22 mm) group. Meanwhile, the gap opening in SCIS (0.05 mm) was reduced by 83% and 59.8% (0.05 to 0.18) compared with the K-wire (0.30 mm) and Cable-pin (0.18 mm) group.

CONCLUSION

SCIS demonstrated improved biomechanical stability for treating transverse patellar fractures compared to MTBW with Kirschner wire and the Cable-Pin system. Finite element analysis showed SCIS substantially reduced fracture fragment displacement and gap opening under various loading conditions.

Candy box technique for the fixation of inferior pole patellar fractures: finite element analysis and biomechanical experiments

BACKGROUND

Maintaining effective reduction and firm fixation in inferior pole patellar fractures is a highly challenging task. There are various treatment methods available; although tension-band wiring combined with cerclage wiring (TBWC) is the mainstream approach, its effectiveness is limited. Herein, we propose and evaluate a new technique called candy box (CB), based on separate vertical wiring (SVW), for the treatment of inferior pole patellar fractures. Specifically, we provide biomechanical evidence for its clinical application.

METHODS

Five fixation models were built: SVW combined with cerclage wiring (SVWC); TBWC; modified SVW with the middle (MSVW-A) or upper (MSVW-B) 1/3 of the steel wire reserved, and CB. A finite element analysis was performed to compare the displacement and stress under 100-N, 200-N, 300-N, 400-N and 500-N force loads. Three-dimensional printing technology was utilized to create fracture models, and the average displacement of each model group was compared under a 500-N force.

RESULTS

The results of the finite element analysis indicate that CB technology exhibits significantly lower maximum displacement, bone stress, and wire stress compared to that with other technologies under different loads. Additionally, in biomechanical experiments, the average force displacement in the CB group was significantly smaller than that with other methods under a 500-N force (P < 0.05).

CONCLUSIONS

CB technology has the potential to overcome the limitations of current techniques due to its superior biomechanical characteristics. By incorporating early functional exercise and ensuring strong internal fixation, patient prognosis could be enhanced. However, further clinical trials are needed to fully evaluate the therapeutic effects of CB technology.

Acetabular Wall Weakening in Total Hip Arthroplasty: A Pilot Study

Total hip arthroplasty is a widely performed operation allowing disabled patients to improve their quality of life to a degree greater than any other elective procedure. Planning for a THA requires adequate patient assessment and preoperative characterizations of acetabular bone loss via radiographs and specific classification schemes. Some surgeons may be inclined to ream at a larger diameter thinking it would lead to a more stable press-fit, but this could be detrimental to the acetabular wall, leading to intraoperative fracture. In the attempt to reduce the incidence of intraoperative fractures, the current study aims to identify how increased reaming diameter degrades and weakens the acetabular rim strength. We hypothesized that there is proportionality between the reaming diameter and the reduction in acetabular strength. To test this hypothesis, this study used bone surrogates, templated from CT scans, and reamed at different diameters. The obtained bone surrogate models were then tested using an Intron 8874 mechanical testing machine (Instron, Norwood, MA) equipped with a custom-made fixture. Analysis of variance (ANOVA) was used to identify differences among reamed diameters while linear regression was used to identify the relationship between reamed diameters and acetabular strength. We found a moderate correlation between increasing reaming diameter that induced thinning of the acetabular wall and radial load damage. For the simplified acetabular model used in this study, it supported our hypothesis and is a promising first attempt in providing quantitative data for acetabular weakening induced by reaming.

Segmental acetabular rim defects, bone loss, oversizing, and press fit cup in total hip arthroplasty evaluated with a probabilistic finite element analysis

PURPOSE

Management of segmental rim defects and bone mineral density (BMD) loss in the elderly prior to total hip replacement is unclear within classification systems for acetabular bone loss. In this study, our objectives were (1) to understand how a reduction in BMD in the elderly affects the oversizing of a press-fit cup for primary fixation and (2) to evaluate whether the location of the segmental defect affected cup fixation.

METHODS

A finite element (FE) model was used to simulate and evaluate cup insertion and fixation in the context of segmental rim defects. We focused on the distribution of patients over age 70 and used BMD (estimated from CT) as a proxy for aging's implications on THR and used probabilistic FE analysis to understand how BMD loss affects oversizing of a press-fit cup.

RESULTS

A cup oversized by 1.10 ± 0.28 mm provides sufficient fixation and lower stresses at the cup-bone interface for elderly patients. Defects in the anterior column and posterior column both required the same mean insertion force for cup seating of 84% (taken as an average of 2 anterior column and 2 posterior column defects) compared to the control configuration, which was 5% greater than the insertion force for a superior rim defect and 12% greater than the insertion force for an inferior rim defect.

CONCLUSIONS

A defect along the superior or inferior rim had a minimal effect on cup fixation, while a defect in the columns created cup instability and increased stress at the defect location.

Primary cup stability in THA with augmentation of acetabular defect. A comparison of healthy and osteoporotic bone

BACKGROUND CONTEXT

Reconstruction of acetabular defect has been advocated as standard procedure in total hip arthroplasty. The presence of bony defects at the acetabulum is viewed as a cause of instability and acetabular wall augmentation is often used without proper consideration of surrounding bone density. The initial cup-bone stability is, however, a challenge and a number of studies supported by clinical follow-ups of patients suggested that if the structural graft needs supporting more than 50% of the acetabular component, a reconstruction cage device spanning ilium to ischium should be preferred to protect the graft and provide structural stability. This study aims to (1) investigate the relationship between cup motion and bone density and (2) quantify the re-distribution of stress at the defect site after augmentation.

HYPHOTESIS

Paprosky type I or II, acetabular defects, when reconstructed with bone screws supported by bioabsorbable calcified triglyceride bone cement are significantly less effective for osteoporotic bone than healthy bone.

MATERIALS AND METHODS

Acetabular wall defects were reconstructed on six cadaveric subjects with bioabsorbable calcified triglyceride bone cement using a re-bar technique. Data of the specimen with higher bone density was used to validate a Finite Element Model. Values of bone apparent density ranging from healthy to osteoporotic were simulated to evaluate (1) the cup motion, through both displacement and rotation, (2) and the von Mises stress distribution.

RESULTS

Defect reconstruction with bone screws and bioabsorbable calcified triglyceride bone cement results in a re-distribution of stress at the defect site. For a reduction of 65% in bone density, the cup displacement was similar to a healthy bone for loads not exceeding 300 N, as load progressed up to 1500 N, the reconstructed defect showed increase of 99 μm (128%) in displacement and of 0.08° in rotation angle.

CONCLUSIONS

Based on the results, we suggest that an alternative solution to wall defect augmentation with bone screws supported by bioabsorbable calcified triglyceride bone cement, be used for osteoporotic bone.

LEVEL OF EVIDENCE

Level IV, experimental and cadaveric study.

Factors influencing initial cup stability in total hip arthroplasty

BACKGROUND

One of the main goals in total hip replacement is to preserve the integrity of the hip kinematics, by well positioning the cup and to make sure its initial stability is congruent and attained. Achieving the latter is not trivial.

METHODS

A finite element model of the cup-bone interface simulating a realistic insertion and analysis of different scenarios of cup penetration, insertion, under-reaming and loading is investigated to determine certain measurable factors sensitivity to stress-strain outcome. The insertion force during hammering and its relation to the cup penetration during implantation is also investigated with the goal of determining the initial stability of the acetabular cup during total hip arthroplasty. The mathematical model was run in various configurations to simulate 1 and 2mm of under-reaming at various imposed insertion distances to mimic hammering and insertion of cup insertion into the pelvis. Surface contact and micromotion at the cup-bone interface were evaluated after simulated cup insertion and post-operative loading conditions.

FINDINGS

The results suggest a direct correlation between under-reaming and insertion force used to insert the acetabular cup on the micromotion and fixation at the cup-bone interface.

INTERPRETATION

While increased under-reaming and insertion force result in an increase amount of stability at the interface, approximately the same percentage of surface contact and micromotion reduction can be achieved with less insertion force. We need to exercise caution to determine the optimal configuration which achieves a good conformity without approaching the yield strength for bone.