Comparison the behavior of ZnO–NP–AC and Na, K doped ZnO–NP–AC for simultaneous removal of Crystal Violet and Quinoline Yellow dyes: Modeling and optimization

A chemometric approach based on response surface methodology for optimization of antibiotic and organic dyes removal from water samples

In this study, the Fe3O4/rGO/Ag magnetic nanocomposite was synthesized and employed as an adsorbent for the removal of tetracycline (TC), crystal violet (CV), and methylene blue (MB) from water samples. The influential parameters in the removal process were identified and optimized using response surface methodology (RSM). Characterization of the product was performed through field emission scanning electron microscopy (FE-SEM), Fourier-transform infrared spectroscopy (FTIR), energy dispersive X-ray spectroscopy (EDX), vibrating-sample magnetometer (VSM), and X-ray diffraction (XRD) analysis. XRD and SEM analysis revealed the successful synthesis of the Fe3O4/rGO/Ag nanocomposite. EDX analysis elucidated the accuracy and clarity of the chemical composition of the magnetic nanocomposite structure. Additionally, the separation of the nano-adsorbent from the solution can be achieved using a magnetic field. Maximum removal of analytes was obtained at pH of 6, amount of nanocomposite 0.014 g, ultrasonic time of 8 min and concentration of 21 mg L-1. Under optimal conditions, the removal efficiencies for TC, CV, and MB were 91.33, 95.82, and 98.19%, respectively. Also, it was observed that after each adsorption-desorption cycle, Fe3O4/rGO/Ag magnetic nanocomposite had good stability to remove TC, CV, and MB. Achieving nearly 98% removal efficiency in optimal conditions showed that Fe3O4/rGO/Ag magnetic nanocomposite is an effective adsorbent for removing TC, CV, and MB from wastewater samples.

Enhanced reactivity of the CuO-Fe2O3 intimate heterojunction for the oxidation of quinoline yellow dye (E104)

This research work describes the degradation of quinoline yellow (QY) in aqueous solutions by the heterogeneous Fenton and photo-Fenton processes in the presence of CuO/Fe₂O₃ photocatalyst. CuO/Fe₂O₃ derived from LDH structure was synthesized by the co-precipitation method. The physiochemical characteristics of CuO/Fe₂O₃ were described by XRD, TEM/SEM, BET surface area, and FTIR techniques. The effects of pH, H₂O₂ concentration, dye concentration, catalyst dose, reaction temperature, and reusability of catalyst on the QY decolorization efficiency were studied. The results indicated that a complete removal of QY was achieved within 150 min, when the H₂O₂ and QY concentrations were 27.6 mM and 100 mg/L, respectively. The rate constants for QY removal by the heterogeneous Fenton system were calculated, and the experimental data were found to fit the pseudo-first order model. Under optimal conditions, the rate constants were, respectively, 0.02032 and 0.01715 min^-1 for the photo-Fenton and Fenton systems; this means that the addition of light has not a noticeable effect.

The Performance of Different AgTiO2 Loading into Poly(3-Nitrothiophene) for Efficient Adsorption of Hazardous Brilliant Green and Crystal Violet Dyes

The in-situ polymerization technology was used to successfully produce nanostructured binary nanocomposites (NCs) made from a poly (3-nitrothiophen) matrix (P3NT) that were loaded effectively with nanoparticles (NPs) of silver titanium dioxide (AgTiO2), of varying percentages (10%, 20%, and 30%). A uniform coating of P3NT covers the AgTiO2 NPs. Various methods were performed to confirm the fabrication of the binary P3NT/AgTiO2 NCs adsorbents, such as FTIR, XRD, SEM, and EDX. Both dyes (brilliant green (B.G.) and crystal violet (C.V.)) were removed from liquid media by using the binary P3NT/AgTiO2 NCs. A range of batch adsorption studies was used to optimize various factors that impact the elimination of B.G. or C.V. dyes, including the pH, weight of the binary P3NT/AgTiO2 NC, proportion of AgTiO2 NP, time, and temperature. The pseudo-second-order kinetics ( $R^2=0.999$ ) was better adapted for the adsorption procedure’s empirical data whereby the maximum adsorption capacity of the C.V. dye was 43.10 mg/g and ( $R^2=0.996$ ) the maximum adsorption potential was 40.16 mg/g for B.G. dye, succeeded by the pseudo-second-order kinetics. Moreover, the adhesion of B.G. and C.V. pigments on the layers of NCs involves an endothermic reaction. In addition, the concocted adsorbent not only exhibited strong adsorption characteristics during four consecutive cycles but also possessed a higher potential for its reuse. According to the findings, the NCs might possibly be used as a robust and reusable adsorbent to remove B.G. and C.V. pigments from an aqueous medium.

Adsorption of dicamba and MCPA onto MIL-53(Al) metal-organic framework: response surface methodology and artificial neural network model studies

An aluminium-based metal–organic framework ((MOF), MIL-53(Al)), was hydrothermally synthesized, characterized and applied for the remediation of the herbicides dicamba (3,6-dichloro-2-methoxy benzoic acid) and 4-chloro-2-methylphenoxyacetic acid (MCPA) in aqueous medium. Response surface methodology (RSM) and artificial neural network (ANN) were used to design, optimize and predict the non-linear relationships between the independent and dependent variables. The shared interaction of the effects of key response parameters on the adsorption capacity were assessed using the central composite design-RSM and ANN optimization models. The optimum adsorption capacities for dicamba and MCPA are 228.5 and 231.9 mg g⁻¹, respectively. The RSM ANOVA results showed significant p-values, with coefficients of determination (R²) = 0.988 and 0.987 and R² adjusted = 0.974 and 0.976 for dicamba and MCPA, respectively. The ANN prediction model gave R² = 0.999 and 0.999, R² adjusted = 0.997 and 0.995 and root mean square errors (RMSEs) of 0.001 and 0.004 for dicamba and MCPA, respectively. In each set of experimental conditions used for the study, the ANN gave better prediction than the RSM, with high accuracy and minimal error. The rapid removal (∼25 min), reusability (5 times) and good agreement between the experimental findings and simulation results suggest the great potential of MIL-53(Al) for the remediation of dicamba and MCPA from water matrices.

Rapid equilibration within a short time, high adsorption capacity, optimization, multivariate interaction of adsorption parameters and artificial neural network prediction model.

Araticum (Annona crassiflora) seed powder (ASP) for the treatment of colored effluents by biosorption

Dyes are widely used in many industrial sectors, many contain harmful substances to human health, and their release into the environment entails several environmental problems, generating a major worldwide concern as water resources are increasingly limited. The development of cheap and efficient biosorbents that remove these pollutants is of utmost importance. In this study, powdered seeds of the araticum fruit (Annona crassiflora) were used in the biosorption of crystal violet (CV) dye from aqueous solutions and simulated textile effluents. Through the characterization techniques, it can be observed that the material presented an amorphous structure, containing an irregular surface composed mainly by groups containing carbon, hydrogen, and oxygen. CV biosorption was favored at the natural pH of the solution (7.5) for a dosage of 0.7 g L^-1 of araticum seed powder. The pseudo-second-order model was the most suitable to represent the biosorption kinetics in the removal of the CV. Biosorption capacity reached equilibrium in the first minutes at the lowest concentrations, and, at the highest, after 120 min. The equilibrium data were well represented by the Langmuir model, with a maximum biosorption capacity of 300.96 mg g^-1 at 328 K. Biosorption had a spontaneous and endothermic nature. In the treatment of a simulated effluent, the biosorbent removed 87.8% of the color, proving to be efficient. Therefore, the araticum seeds powder (ASP) can be used as a low-cost material for the treatment of colored effluents containing the crystal violet (CV) dye.

In Situ Synthesis of MIL-100(Fe) at the Surface of Fe3O4@AC as Highly Efficient Dye Adsorbing Nanocomposite

A new magnetic nanocomposite called MIL-100(Fe) @Fe3O4@AC was synthesized by the hydrothermal method as a stable adsorbent for the removal of Rhodamine B (RhB) dye from aqueous medium. In this work, in order to increase the carbon uptake capacity, magnetic carbon was first synthesized and then the Fe3O4 was used as the iron (III) supplier to synthesize MIL-100(Fe). The size of these nanocomposite is about 30-50 nm. Compared with activated charcoal (AC) and magnetic activated charcoal (Fe3O4@AC) nanoparticles, the surface area of MIL-100(Fe) @Fe3O4@AC were eminently increased while the magnetic property of this adsorbent was decreased. The surface area of AC, Fe3O4@AC, and MIL-100(Fe) @Fe3O4@AC was 121, 351, and 620 m2/g, respectively. The magnetic and thermal property, chemical structure, and morphology of the MIL-100(Fe) @Fe3O4@AC were considered by vibrating sample magnetometer (VSM), thermogravimetric analysis (TGA), zeta potential, X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), Brunner-Emmet-Teller (BET), and transmission electron microscopy (TEM) analyses. The relatively high adsorption capacity was obtained at about 769.23 mg/g compared to other adsorbents to eliminate RhB dye from the aqueous solution within 40 min. Studies of adsorption kinetics and isotherms showed that RhB adsorption conformed the Langmuir isotherm model and the pseudo second-order kinetic model. Thermodynamic amounts depicted that the RhB adsorption was spontaneous and exothermic process. In addition, the obtained nanocomposite exhibited good reusability after several cycles. All experimental results showed that MIL-100(Fe) @Fe3O4@AC could be a prospective sorbent for the treatment of dye wastewater.