The effect of oxidizing agents/systems on the properties of track-etched PET membranes

Porphyrin-Grafted Poly(ethylene terephthalate) as a Reusable and Highly Selective Colorimetric Probe for Mercuric Ion Contaminants in Aqueous Samples

Heavy metals are the most hazardous water pollutants, with severe health and environmental consequences. Among these, mercuric (Hg2+) ions are known to cause detrimental health issues in both humans and aquatic life. Due to this, several analytical techniques have been devised to detect and quantify the amount of this ion. However, most of these require advanced instrumentation, prolonged analysis time, and sample preparation. In this study, a low-cost and highly reusable colorimetric probe was developed by grafting porphyrin to poly(ethylene terephthalate) sheets using an oxazoline polymer as covalent adhesive. Upon exposure to trace amounts of Hg2+ in solution, the fabricated material visually transitioned from faint brownish pink to green by the complexation mechanism. Additionally, the transparency of this probe allowed the quantitative spectrophotometric determination of the Hg2+ concentration in aqueous samples. It was also shown that the material is highly stable, which can be reused for more than 50 times without significant decline in its performance, hence, making it suitable for the onsite monitoring of mercuric ion contamination in different bodies of water.

Surface Modification of Polyethylene Terephthalate Track-Etched Membranes by 2,2,3,3,4,4,5,5,6,6,7,7-Dodecafluoroheptyl Acrylate for Application in Water Desalination by Direct Contact Membrane Distillation

In this work, the surfaces of poly (ethylene terephthalate) track-etched membranes (PET TeMs) with pore sizes of 670-1310 nm were hydrophobized with 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl acrylate (DFHA) by photoinitiated graft polymerization. Attenuated total reflection FTIR spectroscopy (ATR-FTIR), scanning electron microscopy (SEM) coupled to an energy-dispersive X-ray spectrometer (EDX), and contact angle measurements were used to identify and characterize the TeMs. The optimal parameters for graft polymerization were determined as follows: polymerization time of 60 min, monomer concentration of 30%, and distance from the UV source of 7 cm. The water contact angle of the modified membranes reached 97°, which is 51° for pristine membranes. The modified membranes were tested for water desalination using direct contact membrane distillation (DCMD) method. The effects of membrane pore size, the degree of grafting, and salt concentration on the performance of membrane distillation process were investigated. According to the results obtained, it has been concluded that large pore size hydrophobic TeMs modified by using DFHA could be used for desalinating water.

Preparation of a Molecularly Imprinted Polymer on Polyethylene Terephthalate Platform Using Reversible Addition-Fragmentation Chain Transfer Polymerization for Tartrazine Analysis via Smartphone

This work describes the preparation of a molecularly imprinted polymer (MIP) platform on polyethylene terephthalate (MIP-PET) via RAFT polymerization for analyzing tartrazine using a smartphone. The MIP-PET platform was characterized using Fourier transform infrared (FTIR) techniques, Raman Spectroscopy, X-ray photoelectron spectroscopy (XPS), and confocal microscopy. The optimal pH and adsorption time conditions were determined. The adsorption capacity of the MIP-PET plates with RAFT treatment (0.057 mg cm-2) was higher than that of the untreated plates (0.028 mg cm-2). The kinetic study revealed a pseudo-first-order model with intraparticle diffusion, while the isotherm study indicated a fit for the Freundlich model. Additionally, the MIP-PET demonstrated durability by maintaining its adsorption capacity over five cycles of reuse without significant loss. To quantify tartrazine, images were captured using a smartphone, and the RGB values were obtained using the ImageJ® free program. A partial least squares regression (PLS) was performed, obtaining a linear range of 0 to 7 mg L-1 of tartrazine. The accuracy of the method was 99.4% (4.97 ± 0.74 mg L-1) for 10 samples of 5 mg L-1. The concentration of tartrazine was determined in two local soft drinks (14.1 mg L-1 and 16.5 mg L-1), with results comparable to the UV-visible spectrophotometric method.

e-Beam and γ-rays Induced Synthesis and Catalytic Properties of Copper Nanoclusters-Deposited Composite Track-Etched Membranes

Effective removal of toxic inorganic and organic pollutants is one of the current leading challenges of wastewater treatment. In this study, the decomposition of methylene blue (MB) under UV light irradiation was investigated in the presence of copper nanoclusters (NCs)-deposited polyethylene terephthalate (PET) track-etched hybrid membranes. PET track-etched membranes (TeMs) with an average pore size of ~400 nm were grafted by functional acrylic acid (AA) monomer under electron beam irradiation after oxidation with H₂O₂/UV system. The radiation dose varied between 46 and 200 kGy. For the deposition of copper NCs, poly(acrylic acid) (PAA)-grafted membranes saturated with Cu(II) ions were irradiated either by electron beam or γ-rays to obtain copper-based NCs for the catalytic degradation of MB. Irradiation to 100 kGy with accelerated electrons resulted in the formation of small and uniform copper hydroxide (Cu(OH)₂) nanoparticles homogeneously distributed over the entire volume of the template. On the other hand, irradiation under γ-rays yielded composites with copper NCs with a high degree of crystallinity. However, the size of the deposited NCs obtained by γ-irradiation was not uniform. Nanoparticles with the highest uniformity were obtained at 150 kGy dose. Detailed analysis by X-ray diffraction (XRD) and scanning electron microscopy (SEM) confirmed the loading of copper nanoparticles with an average size of 100 nm on the inner walls of nanochannels and on the surface of PET TeMs. Under UV light irradiation, composite membranes loaded with NCs exhibited high photocatalytic activity. It was determined that the highest catalytic activity was observed in the presence of Cu(OH)₂@PET-g-PAA membrane obtained at 250 kGy. More than 91.9% of the initial dye was degraded when this hybrid membrane was employed for 180 min, while only 83.9% of MB was degraded under UV light using Cu@PET-g-PAA membrane. Cu(OH)₂@PET-g-PAA membranes obtained under electron beam irradiation demonstrated a higher photocatalytic activity compared to Cu@PET-g-PAA membranes attained by γ-rays.

Stimuli-Responsive Track-Etched Membranes for Separation of Water-Oil Emulsions

In this work, we have developed a method for the preparation of pH-responsive track-etched membranes (TeMs) based on poly(ethylene terephthalate) (PET) with pore diameters of 2.0 ± 0.1 μm of cylindrical shape by RAFT block copolymerization of styrene (ST) and 4-vinylpyridine (4-VP) to be used in the separation of water-oil emulsions. The influence of the monomer concentration (1-4 vol%), the molar ratio of RAFT agent: initiator (1:2-1:100) and the grafting time (30-120 min) on the contact angle (CA) was studied. The optimal conditions for ST and 4-VP grafting were found. The obtained membranes showed pH-responsive properties: at pH 7-9, the membrane was hydrophobic with a CA of 95°; at pH 2, the CA decreased to 52°, which was due to the protonated grafted layer of poly-4-vinylpyridine (P4VP), which had an isoelectric point of pI = 3.2. The obtained membranes with controlled hydrophobic-hydrophilic properties were tested by separating the direct and reverse "oil-water" emulsions. The stability of the hydrophobic membrane was studied for 8 cycles. The degree of purification was in the range of 95-100%.

Fully integrated colorimetric sensor based on transparency substrate for salbutamol determination

•

Facile colorimetric method for the determination of salbutamol based on a simple redox reaction using permanganate as reagent was first investigated at the transparency-based analytical device (TAD).

•

The colorimetric TAD sensor was in-lab constructed using a transparent PET-based substrate, showing good compatibility with the permanganate reagent which could result in a vivid color change, clearly observed by the naked eye.

•

This proposed colorimetric TAD sensor was successfully applied for salbutamol determination in real drug samples with good accuracy and satisfactory recovery, highlighting the potential capability of this TAD-based colorimetric sensor in pharmaceutical application.

A facile colorimetric method based on a typical redox reaction was first developed for the determination of salbutamol (SAL) using a low-cost and portable transparency-based analytical device (TAD). The TAD was simply fabricated by wax-printing onto a transparent polymer-based substrate to create the hydrophobic barriers and the colorimetric reaction zones where the color changes could be easily observed with the naked eye. Potassium permanganate (KMnO₄), a common oxidizing agent, was deliberately used as a colorimetric reagent for SAL. Once SAL reacted with KMnO₄ in the acidified system, it could undergo oxidation and the color of KMnO₄ subsequently changed from light pink to orange. The color change corresponding to the SAL concentration could be clearly observed at the TAD sensor. In addition, the reaction color could be recorded using a digital camera and then analyzed by ImageJ for quantitative analysis. Under the optimized conditions, the developed method together with the TAD sensor exhibited high efficiency for SAL determination with linearity ranging from 0.5 to 40 mg·L⁻¹ and a limit of detection (LOD) of 0.05 mg·L⁻¹.

•

This proposed TAD-based colorimetric method using permanganate as color reagent showed excellent performance in SAL detection with good accuracy and high precision.

Hybrid PET Track-Etched Membranes Grafted by Well-Defined Poly(2-(dimethylamino)ethyl methacrylate) Brushes and Loaded with Silver Nanoparticles for the Removal of As(III)

Nanoporous track-etched membranes (TeM) are promising materials as adsorbents to remove toxic pollutants, but control over the pore diameter and density in addition to precise functionalization of nanochannels is crucial for controlling the surface area and efficiency of TeMs. This study reported the synthesis of functionalized PET TeMs as high-capacity sorbents for the removal of trivalent arsenic, As(III), which is more mobile and about 60 times more toxic than As(V). Nanochannels of PET-TeMs were functionalized by UV-initiated reversible addition fragmentation chain transfer (RAFT)-mediated grafting of 2-(dimethyamino)ethyl methacrylate (DMAEMA), allowing precise control of the degree of grafting and graft lengths within the nanochannels. Ag NPs were then loaded onto PDMAEMA-g-PET to provide a hybrid sorbent for As(III) removal. The As(III) removal efficiency of Ag@PDMAEMA-g-PET, PDMAEMA-g-PET, and pristine PET TeM was compared by adsorption kinetics studies at various pH and sorption times. The adsorption of As(III) by Ag@DMAEMA-g-PET and DMAEMA-g-PET TeMs was found to follow the Freundlich mechanism and a pseudo-second-order kinetic model. After 10 h, As(III) removal efficiencies were 85.6% and 56% for Ag@PDMAEMA-g-PET and PDMAEMA-g-PET, respectively, while PET template had a very low arsenic sorption capacity of 17.5% at optimal pH of 4.0, indicating that both PDMAEMA grafting and Ag-NPs loading significantly increased the As(III) removal capacity of PET-TeMs.

Preparation of Hydrophobic PET Track-Etched Membranes for Separation of Oil-Water Emulsion

The paper describes the separation of an oil–water emulsion by filtration using poly(ethylene terephthalate) track-etched membranes (PET TeMs) with regular pore geometry and narrow pore size distribution. PET TeMs were modified with trichloro(octyl)silane to increase their hydrophobic properties. Conditions for the modification of PET TeMs with trichloro(octyl)silane were investigated. The results of changes in the pore diameters and the contact angle depend on the concentration of trichloro(octyl)silane and the soaking time are presented. The obtained samples were characterized by FTIR, AFM, SEM-EDX and gas-permeability test. Chloroform–water and cetane–water emulsions have been used as a test liquid for oil–water separation.

Recent Progress in the Membrane Distillation and Impact of Track-Etched Membranes

Membrane distillation (MD) is a rapidly developing field of research and finds applications in desalination of water, purification from nonvolatile substances, and concentration of various solutions. This review presents data from recent studies on the MD process, MD configuration, the type of membranes and membrane hydrophobization. Particular importance has been placed on the methods of hydrophobization and the use of track-etched membranes (TeMs) in the MD process. Hydrophobic TeMs based on poly(ethylene terephthalate) (PET), poly(vinylidene fluoride) (PVDF) and polycarbonate (PC) have been applied in the purification of water from salts and pesticides, as well as in the concentration of low-level liquid radioactive waste (LLLRW). Such membranes are characterized by a narrow pore size distribution, precise values of the number of pores per unit area and narrow thickness. These properties of membranes allow them to be used for more accurate water purification and as model membranes used to test theoretical models (for instance LEP prediction).

Evaluation of the effectiveness, safety, and feasibility of 9 potential biocides to disinfect acidic landfill leachate from algae and bacteria

This study evaluates 9 biocides as disinfectants against microbiological contaminants, specifically, microalgae and E. coli, while assessing their safety and environmental impact. Specifically, the biocide effectiveness and corresponding generation of halogenated compounds is assessed in a real contaminated groundwater receiving acidic leachate from a phosphogypsum landfill. Oxidizing agents are investigated, namely, hypochlorite, peracetic acid, hydrogen peroxide, chlorine dioxide, and persulfate, together with electrophilic biocides, namely, 2,2-dibromo-2-cyanoacetamide and (chloro-) methylisothiazolinone. In addition, a novel disinfection approach is assessed by applying reducing agents, namely, sulfite and metabisulfite. The disinfection mechanism and the formation of halogenated compounds are discussed on the basis of the mode of action and of the molecular structure of each biocide. Overall, the results show that an optimal dosage of the biocides exists to minimize the formation of harmful compounds in water while maximizing disinfection, especially for hypochlorite and peracetic acid. This dosage was between 0.03 mM and 0.15 mM depending on the biocide. The safety of electrophilic biocides is found to be associated to their molecular structure rather than their mode of action. Hydrogen peroxide, MIT, and metabisulfite are the most promising disinfectants in the contaminated groundwater matrix of interest since no halogenated by-products are detected upon successful disinfection, while they are able to completely inactivate bacteria and remove over the 80% of microalgae in the selected matrix. In particular, metabisulfite represents a highly promising biocide, owing to its low environmental and health impacts, as well as economic feasibility (estimated reagent cost ~0.002 € per cubic meter of treated water).

Modification of PET Ion-Track Membranes by Silica Nanoparticles for Direct Contact Membrane Distillation of Salt Solutions

The paper describes desalination by membrane distillation (MD) using ion-track membranes. Poly(ethylene terephthalate) (PET) ion-track membranes were hydrophobized by the immobilization of hydrophobic vinyl-silica nanoparticles (Si NPs). Si NPs were synthesized by the sol-gel method, and the addition of the surfactant led to the formation of NPs with average size of 40 nm. The thermal initiator fixed to the surface of membranes allowed attachment of triethoxyvinyl silane Si NPs at the membrane surface. To further increase hydrophobicity, ethoxy groups were fluorinated. The morphology and chemical structure of prepared membranes were characterized by SEM, FTIR, XPS spectroscopy, and a gas permeability test. Hydrophobic properties were evaluated by contact angle (CA) and liquid entry pressure (LEP) measurements. Membranes with CA 125–143° were tested in direct contact membrane distillation (DCMD) of 30 g/L saline solution. Membranes showed water fluxes from 2.2 to 15.4 kg/(m²·h) with salt rejection values of 93–99%.