1
|
Gonçalves LFFF, Reis RL, Fernandes EM. Forefront Research of Foaming Strategies on Biodegradable Polymers and Their Composites by Thermal or Melt-Based Processing Technologies: Advances and Perspectives. Polymers (Basel) 2024; 16:1286. [PMID: 38732755 PMCID: PMC11085284 DOI: 10.3390/polym16091286] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/12/2024] [Revised: 04/13/2024] [Accepted: 04/26/2024] [Indexed: 05/13/2024] Open
Abstract
The last few decades have witnessed significant advances in the development of polymeric-based foam materials. These materials find several practical applications in our daily lives due to their characteristic properties such as low density, thermal insulation, and porosity, which are important in packaging, in building construction, and in biomedical applications, respectively. The first foams with practical applications used polymeric materials of petrochemical origin. However, due to growing environmental concerns, considerable efforts have been made to replace some of these materials with biodegradable polymers. Foam processing has evolved greatly in recent years due to improvements in existing techniques, such as the use of supercritical fluids in extrusion foaming and foam injection moulding, as well as the advent or adaptation of existing techniques to produce foams, as in the case of the combination between additive manufacturing and foam technology. The use of supercritical CO2 is especially advantageous in the production of porous structures for biomedical applications, as CO2 is chemically inert and non-toxic; in addition, it allows for an easy tailoring of the pore structure through processing conditions. Biodegradable polymeric materials, despite their enormous advantages over petroleum-based materials, present some difficulties regarding their potential use in foaming, such as poor melt strength, slow crystallization rate, poor processability, low service temperature, low toughness, and high brittleness, which limits their field of application. Several strategies were developed to improve the melt strength, including the change in monomer composition and the use of chemical modifiers and chain extenders to extend the chain length or create a branched molecular structure, to increase the molecular weight and the viscosity of the polymer. The use of additives or fillers is also commonly used, as fillers can improve crystallization kinetics by acting as crystal-nucleating agents. Alternatively, biodegradable polymers can be blended with other biodegradable polymers to combine certain properties and to counteract certain limitations. This work therefore aims to provide the latest advances regarding the foaming of biodegradable polymers. It covers the main foaming techniques and their advances and reviews the uses of biodegradable polymers in foaming, focusing on the chemical changes of polymers that improve their foaming ability. Finally, the challenges as well as the main opportunities presented reinforce the market potential of the biodegradable polymer foam materials.
Collapse
Affiliation(s)
- Luis F. F. F. Gonçalves
- 3B’s Research Group, I3Bs–Research Institute on Biomaterials, Biodegradables and Biomimetics, University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine, AvePark, Parque de Ciência e Tecnologia, Zona Industrial da Gandra, Barco, 4805-017 Guimarães, Portugal;
- ICVS/3B’s—PT Government Associate Laboratory, Barco, 4805-017 Guimarães, Portugal
| | - Rui L. Reis
- 3B’s Research Group, I3Bs–Research Institute on Biomaterials, Biodegradables and Biomimetics, University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine, AvePark, Parque de Ciência e Tecnologia, Zona Industrial da Gandra, Barco, 4805-017 Guimarães, Portugal;
- ICVS/3B’s—PT Government Associate Laboratory, Barco, 4805-017 Guimarães, Portugal
| | - Emanuel M. Fernandes
- 3B’s Research Group, I3Bs–Research Institute on Biomaterials, Biodegradables and Biomimetics, University of Minho, Headquarters of the European Institute of Excellence on Tissue Engineering and Regenerative Medicine, AvePark, Parque de Ciência e Tecnologia, Zona Industrial da Gandra, Barco, 4805-017 Guimarães, Portugal;
- ICVS/3B’s—PT Government Associate Laboratory, Barco, 4805-017 Guimarães, Portugal
| |
Collapse
|
2
|
Ji E, Zhou H, Xu G, Wang X, Wang L, Gao J, Yan J. Insights into heterogeneous surface induced bubble nucleation mechanisms in cellulose reinforced polylactic acid foams. Int J Biol Macromol 2024; 268:131659. [PMID: 38641275 DOI: 10.1016/j.ijbiomac.2024.131659] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 01/17/2024] [Revised: 04/03/2024] [Accepted: 04/15/2024] [Indexed: 04/21/2024]
Abstract
As the most abundant natural homo-polymer, cellulose has the potential to enhance polymer properties reducing the cost of raw materials. In this work, the carboxylate cellulose nanofiber (CNF-C) was selected to modify polylactic acid (PLA) foams, and the density functional theory was constructed to help analyze the foaming mechanism quantitatively. The theoretical results showed that the ordered structure, the carboxyl and the hydroxyl of CNF-C were more conducive to providing much stronger CO2 adsorption for bubble nucleation, where the predicted critical bubble size decreased and the cell density increased with the addition of CNF-C. The experimental results revealed that the CNF-C promoted the rheological properties and crystallization behaviors of PLA samples, the PLA/CNF-C foams were characterized with uniform structures, the average cell size decreased from 21.39 μm to 0.19 μm, and the cell number density increased from 2.65×1010cell/cm3 to 2.30×1014cell/cm3. Those improvements resulted in an increase of 394.0 % for the compressive strength of the prepared foams. Generally, the high-performance PLA/CNF-C foams were fabricated successfully without compromising the properties of bio-based and biodegradable, the foaming mechanism was analyzed combining theoretical results with experimental data, and it was believed to provide a guide for cellulose reinforcing biodegradable polymer materials.
Collapse
Affiliation(s)
- Enle Ji
- College of Science & Technology, Hebei Agricultural University, Huanghua, Hebei 061100, People's Republic of China
| | - Hongfu Zhou
- Key Laboratory of Processing and Application of Polymeric Foams of China National Light Industry Council, School of Light Industry Science and Engineering, Beijing Technology and Business University, Beijing 100048, People's Republic of China.
| | - Guohe Xu
- College of Science & Technology, Hebei Agricultural University, Huanghua, Hebei 061100, People's Republic of China
| | - Xiangdong Wang
- Key Laboratory of Processing and Application of Polymeric Foams of China National Light Industry Council, School of Light Industry Science and Engineering, Beijing Technology and Business University, Beijing 100048, People's Republic of China
| | - Linyan Wang
- College of Science & Technology, Hebei Agricultural University, Huanghua, Hebei 061100, People's Republic of China.
| | - Jianping Gao
- College of Science & Technology, Hebei Agricultural University, Huanghua, Hebei 061100, People's Republic of China
| | - Jundian Yan
- College of Science & Technology, Hebei Agricultural University, Huanghua, Hebei 061100, People's Republic of China
| |
Collapse
|
3
|
Huang F, Liu W, Lai J, Wu J, Huang A, Geng L, Peng X. Enhanced heat resistance and expansion ratio of biodegradable poly (lactic acid)/poly (butylene adipate-co-terephthalate) composite foams via synergistic effect of nucleating agent and chain extension. JOURNAL OF POLYMER ENGINEERING 2023. [DOI: 10.1515/polyeng-2022-0284] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 03/15/2023]
Abstract
Abstract
Environmentally friendly foams have been studied extensively to handle the plastic pollution caused by disposable tableware. Herein, biodegradable poly (lactic acid) (PLA) – poly (butylene adipate-co-terephthalate) (PBAT) composites were first fabricated by melt blending, in which a reactive chain extender (ADR) was incorporated to enhance the interfacial compatibility and melt strength, a nucleating agent (TMC) was applied to improve the crystallinity. Subsequently, the foaming behavior of the composites was investigated via supercritical CO2 foaming. Specifically, a spherulite and shish-kebab-like nanoporous structure was observed from PLA and PLA/TMC foams, respectively, when the soaking temperature was far below melting temperature. With an increase of foaming temperature, the unmelted completely crystals served as physical cross-linking points, also contributing to a high melt strength. Combined with chain extension reaction of ADR, the PLA–PBAT/ADR/TMC foams showed the largest cell diameter and expansion ratio, which were 19 μm and 8.9, respectively. Furthermore, the heat resistance of PLA–PBAT/ADR/TMC foams was also significantly improved, owing to the high crystallinity induced by TMC. Consequently, the composite foams with superior heat resistance and toughness were obtained to broaden its application as biodegradable disposable tableware for hot food.
Collapse
Affiliation(s)
- Feng Huang
- Key Laboratory of Polymer Materials and Products of Universities in Fujian, Department of Materials Science and Engineering , Fujian University of Technology , Fuzhou , Fujian 350118 , China
| | - Wei Liu
- Key Laboratory of Polymer Materials and Products of Universities in Fujian, Department of Materials Science and Engineering , Fujian University of Technology , Fuzhou , Fujian 350118 , China
| | - Jun Lai
- Key Laboratory of Polymer Materials and Products of Universities in Fujian, Department of Materials Science and Engineering , Fujian University of Technology , Fuzhou , Fujian 350118 , China
| | - Jianming Wu
- Key Laboratory of Polymer Materials and Products of Universities in Fujian, Department of Materials Science and Engineering , Fujian University of Technology , Fuzhou , Fujian 350118 , China
| | - An Huang
- Key Laboratory of Polymer Materials and Products of Universities in Fujian, Department of Materials Science and Engineering , Fujian University of Technology , Fuzhou , Fujian 350118 , China
| | - Lihong Geng
- Key Laboratory of Polymer Materials and Products of Universities in Fujian, Department of Materials Science and Engineering , Fujian University of Technology , Fuzhou , Fujian 350118 , China
| | - Xiangfang Peng
- Key Laboratory of Polymer Materials and Products of Universities in Fujian, Department of Materials Science and Engineering , Fujian University of Technology , Fuzhou , Fujian 350118 , China
| |
Collapse
|
4
|
Yan X, Chen L, Tian H, Jia S, Wang X, Pan H, Han L, Bian J, Yang H, Wu G, Zhao Y, Zhang H. Enhancement of the compatibility, mechanical properties, and heat resistance of poly(butylene succinate-co-terephthalate)/poly(butylene succinate) blends by the addition of chain extender and nucleating agent. JOURNAL OF POLYMER RESEARCH 2023. [DOI: 10.1007/s10965-023-03486-z] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 02/18/2023]
|
5
|
Zhou G, Liu W, Yin H, Zhang Y, Huang C. Effect of nano‐sized zinc citrate on the supercritical carbon dioxide‐assisted extrusion foaming behavior of poly(lactic acid). J Appl Polym Sci 2023. [DOI: 10.1002/app.53561] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/03/2023]
Affiliation(s)
- Gang Zhou
- School of Chemistry and Materials Engineering Wenzhou University Wenzhou China
| | - Wenjun Liu
- Institute of New Materials & Industry Technology Wenzhou University Wenzhou China
| | - Haiyan Yin
- Biomaterials Division, Wenzhou Institute University of Chinese Academy of Sciences Wenzhou China
| | - Yinhang Zhang
- School of Chemistry and Materials Engineering Wenzhou University Wenzhou China
| | - Chengzhe Huang
- School of Chemistry and Materials Engineering Wenzhou University Wenzhou China
| |
Collapse
|
6
|
Peng K, Mubarak S, Diao X, Cai Z, Zhang C, Wang J, Wu L. Progress in the Preparation, Properties, and Applications of PLA and Its Composite Microporous Materials by Supercritical CO 2: A Review from 2020 to 2022. Polymers (Basel) 2022; 14:polym14204320. [PMID: 36297898 PMCID: PMC9611929 DOI: 10.3390/polym14204320] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/02/2022] [Revised: 09/22/2022] [Accepted: 10/11/2022] [Indexed: 11/16/2022] Open
Abstract
The development of degradable plastic foams is in line with the current development concept of being pollution free and sustainable. Poly(lactic acid) (PLA) microporous foam with biodegradability, good heat resistance, biocompatibility, and mechanical properties can be successfully applied in cushioning packaging, heat insulation, noise reduction, filtration and adsorption, tissue engineering, and other fields. This paper summarizes and critically evaluates the latest research on preparing PLA microporous materials by supercritical carbon dioxide (scCO2) physical foaming since 2020. This paper first introduces the scCO2 foaming technologies for PLA and its composite foams, discusses the CO2-assisted foaming processes, and analyzes the effects of process parameters on PLA foaming. After that, the paper reviews the effects of modification methods such as chemical modification, filler filling, and mixing on the rheological and crystallization behaviors of PLA and provides an in-depth analysis of the mechanism of PLA foaming behavior to provide theoretical guidance for future research on PLA foaming. Lastly, the development and applications of PLA microporous materials based on scCO2 foaming technologies are prospected.
Collapse
Affiliation(s)
- Kangming Peng
- CAS Haixi Industrial Technology Innovation Center in Beilun, Ningbo 315830, China
- College of Chemistry and Materials Science, Fujian Normal University, Fuzhou 350007, China
- CAS Key Laboratory of Design and Assembly of Functional Nanostructures, Fujian Key Laboratory of Nanomaterials, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002, China
| | - Suhail Mubarak
- Department of Chemical and Biomolecular Engineering, Chonnam National University, Yeosu-si 59626, Jeonnam, Korea
| | - Xuefeng Diao
- Jinyoung (Xiamen) Advanced Materials Technology Co., Ltd., Xiamen 361028, China
| | - Zewei Cai
- CAS Haixi Industrial Technology Innovation Center in Beilun, Ningbo 315830, China
- CAS Key Laboratory of Design and Assembly of Functional Nanostructures, Fujian Key Laboratory of Nanomaterials, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002, China
- College of Chemistry, Fuzhou University, Fuzhou 350116, China
| | - Chen Zhang
- School of Materials and Chemistry Engineering, Minjiang University, Xiyuangong Road No. 200, Fuzhou 350108, China
- Industrial Design Institute, Minjiang University, Xiyuangong Road No. 200, Fuzhou 350108, China
- Correspondence: (C.Z.); (J.W.); (L.W.)
| | - Jianlei Wang
- CAS Haixi Industrial Technology Innovation Center in Beilun, Ningbo 315830, China
- CAS Key Laboratory of Design and Assembly of Functional Nanostructures, Fujian Key Laboratory of Nanomaterials, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002, China
- Correspondence: (C.Z.); (J.W.); (L.W.)
| | - Lixin Wu
- CAS Key Laboratory of Design and Assembly of Functional Nanostructures, Fujian Key Laboratory of Nanomaterials, Fujian Institute of Research on the Structure of Matter, Chinese Academy of Sciences, Fuzhou 350002, China
- Correspondence: (C.Z.); (J.W.); (L.W.)
| |
Collapse
|
7
|
Wu Y, Zhang S, Han S, Yu K, Wang L. Regulating cell morphology of poly (lactic acid) foams from microcellular to nanocellular by crystal nucleating agent. Polym Degrad Stab 2022. [DOI: 10.1016/j.polymdegradstab.2022.110117] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/25/2022]
|
8
|
The synergistic effect of polytetrafluoroethylene in-situ fibrillation and dibenzoyl sebacate hydrazide on the crystallization and foaming behavior of poly (lactic acid). Int J Biol Macromol 2022; 221:523-535. [PMID: 36089093 DOI: 10.1016/j.ijbiomac.2022.09.032] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/17/2022] [Revised: 09/03/2022] [Accepted: 09/05/2022] [Indexed: 11/22/2022]
Abstract
The fully degradable poly (lactic acid) foam with green environmental protection characteristics can alleviate the shortage of petroleum resources caused by the application of plastics. However, due to the inherent low melt strength and slow crystallization rate of linear PLA. It is difficult to obtain PLA microcellular foam with good morphology. In order to obtain PLA microcellular foam with ultra-high expansion ratio and small cell size, PTFE (polytetrafluoroethylene) nanofibers with excellent CO2 adsorption rate were introduced. Self-assembled nucleator TMC-300(dibenzoyl sebacate hydrazide) was also introduced to blend with PLA to obtain small-sized cells. The results show that the PTFE entanglement network as a self-assembled template can effectively improve the early crystallization nucleation efficiency and increase the crystallinity of branched PLA (CBPLA)/TMC by 7 %. The microcellular foam with PTFE content of 0.5 wt% (CBPLA/TMC/PTFE 0.5) was successfully prepared by physical foaming agent, which had the lowest cell size (8.7 μm) And high expansion ratio (1200 %).
Collapse
|