Influence of reduced graphene oxide on the rheological response and chain orientation on shear deformation of high density polyethylene

Hybrid Printing Using Cellulose Nanocrystals Reinforced GelMA/HAMA Hydrogels for Improved Structural Integration

3D printing of soft-tissue like cytocompatible single material constructs with appropriate mechanical properties remains a challenge. Hybrid printing technology provides an attractive alternative as it combines a cell-free ink for providing mechanical support with a bioink for housing embedded cells. Several hybrid printed structures have been developed, utilizing thermoplastic polymers such as polycaprolactone as structural support. These thermoplastics demonstrated limited structural integration with the cell-laden components, and this may compromise the overall performance. In this work, a hybrid printing platform is presented using two distinct hydrogel inks that share the same photo-crosslinking chemistry to enable simple fabrication and seamless structural integration. A mechanically reinforced hydrogel ink is developed comprising cellulose nanocrystals and gelatin methacryloyl/hyaluronic acid methacrylate (GelMA/HAMA) as the structural component, and GelMA/HAMA as the cytogel containing a mouse chondrogenic cell line, ATDC5. Hybrid printed constructs with encapsulated cells are fabricated using the two optimized inks, and the structural integration of the constructs is evaluated by cyclic mechanical compression. Finally, the cell viability of encapsulated ATDC5 cells in the hybrid printed structures is evaluated.

Non-Isothermal Crystallisation Kinetics of Carbon Black- Graphene-Based Multimodal-Polyethylene Nanocomposites

The effect of carbon black (CB) and microwave-induced plasma graphene (g) on the crystallisation kinetics of the multimodal high-density polyethylene was studied under non-isothermal conditions. The non-isothermal crystallisation behaviour of the multimodal-high-density polyethylene (HDPE), containing up to 5 wt.% graphene, was compared with that of neat multimodal-HDPE and its carbon black based nanocomposites. The results suggested that the non-isothermal crystallisation behaviour of polyethylene (PE)-g nanocomposites relied significantly on both the graphene content and the cooling rate. The addition of graphene caused a change in the mechanism of the nucleation and the crystal growth of the multimodal-HDPE, while carbon black was shown to have little effect. Combined Avrami and Ozawa equations were shown to be effective in describing the non-isothermal crystallisation behaviour of the neat multimodal-HDPE and its nanocomposites. The mean activation energy barrier (ΔE), required for the transportation of the molecular chains from the melt state to the growing crystal surface, gradually diminished as the graphene content increased, which is attributable to the nucleating agent effect of graphene platelets. On the contrary, the synergistic effect resulting from the PE-CB nanocomposite decreased the ΔE of the neat multimodal-HDPE significantly at the lowest carbon black content.

An Unconventional Polymerization Route to Hydrophilic Fluorescent Organic Nanoparticles for Multicolor Cellular Bioimaging

We demonstrated an unconventional polymerization route to synthesize hydrophilic fluorescent organic nanoparticles (FONs) for multicolor cellular bioimaging in this contribution. The route benefits from our unexpected discovery of a rapid polymerization reaction between 1,6-hexanediol dipropiolate and 2,4,6-triazide-1,3,5-triazine under the catalysis of N,N,N',N'',N''-pentamethyldiethylenetriamine (PMDETA). Interestingly, the 2,4,6-triazide-1,3,5-triazine and PMDETA system can also induce rapid free radical polymerization at room temperature. The as-prepared FONs exhibited promising water solubility and stability with an average diameter of 20 nm. The excitation wavelength-dependent fluorescent properties endow the FONs with blue, yellow, and red fluorescent emission under UV, blue, and green excitation, respectively. The cytotoxicity of FONs was investigated by using a Cell Counting Kit (CCK-8) assay, which indicated good biocompatiblity. More importantly, the cell uptake experiment verified the FONs were excellent fluorescent nanoprobes for multicolor cellular bioimaging. Therefore, this unconventional route provides a novel fabrication strategy of highly hydrophilic FONs for biomedical applications.