Rheology of fumed silica/polypropylene glycol dispersions

3D Printing of Thermally Responsive Shape Memory Liquid Crystalline Epoxy Networks

A two-component liquid crystalline epoxy network (LCEN) with shape memory behavior was developed and evaluated as a candidate material for 3D printing. The cure kinetics of the uncured material and the shape memory properties of the cured LCEN were investigated by using parallel plate rheology and dynamic mechanical analysis, respectively. A commercially available fumed silica additive was introduced to the neat, uncured material to improve the rheological properties for 3D printing. The addition of fumed silica was found to increase the yield stress, shear-thinning behavior, and toughness of the uncured epoxy ink. Polarized light microscopy, differential scanning calorimetry, and wide-angle X-ray scattering measurements between the neat and additive-modified LCEN suggested a reduction in liquid crystalline alignment in the modified LCEN, owing to interactions between crystalline domains and fumed silica, which in turn influenced the mechanical behavior. Overall, the additive was found to be successful in preserving the shape memory properties of LCEN while improving its printability.

In Situ Observation of Shear-Induced Jamming Front Propagation during Low-Velocity Impact in Polypropylene Glycol/Fumed Silica Shear Thickening Fluids

Shear jamming, a relatively new type of phase transition from discontinuous shear thickening into a solid-like state driven by shear in dense suspensions, has been shown to originate from frictional interactions between particles. However, not all dense suspensions shear jam. Dense fumed silica colloidal systems have wide applications in the industry of smart materials from body armor to dynamic dampers due to extremely low bulk density and high colloid stability. In this paper, we provide new evidence of shear jamming in polypropylene glycol/fumed silica suspensions using optical in situ speed recording during low-velocity impact and explain how it contributes to impact absorption. Flow rheology confirmed the presence of discontinuous shear thickening at all studied concentrations. Calculations of the flow during impact reveal that front propagation speed is 3–5 times higher than the speed of the impactor rod, which rules out jamming by densification, showing that the cause of the drastic impact absorption is the shear jamming. The main impact absorption begins when the jamming front reaches the boundary, creating a solid-like plug under the rod that confronts its movement. These results provide important insights into the impact absorption mechanism in fumed silica suspensions with a focus on shear jamming.

Fumed Silica-Based Suspensions for Shear Thickening Applications: A Full-Scale Rheological Study

Understanding shear thickening fluids (STFs) is critically important in a broad spectrum of fields ranging from biology to military. STFs are referred to the suspension of solid particles in an inert carrier liquid. Customizing the thickening behavior is vital for obtaining desired properties. Hence, comprehending shear thickening mechanisms is necessary to fully understand the factors affecting the shear thickening response of the STFs. Herein, we systematically investigate the effects of a wide range of parameters, from inherent properties of the constituents, including size and surface chemistry of the suspended particles, to practical conditions such as temperature and shear history, on the shear thickening behavior of fumed silica nanoparticles (NPs)-based suspensions in a polyethylene glycol (PEG) medium. Accordingly, increasing the hydrophobicity of the silica NPs or decreasing the NP size transforms the suspensions from sol to gel. The sol systems exhibit a strong shear thickening response, while shear thinning behavior is prominent in the strong gel systems. Hybridization of different silica NPs is also leveraged to tune the shear thickening behavior. In addition, we showcase the decisive role of operating temperature or shear history on the shear thickening behavior of suspensions. For instance, in terms of the shear history, above a critical value of preshear, the shear thickening behavior occurs at lower shear rates for STFs containing hydrophilic NPs. It is believed that the provided insights in this study can pave the way for developing advanced STFs with prescribed features.

The role of solvent molecular weight in shear thickening and shear jamming

The application of stress can drive a dense suspension into a regime of highly non-Newtonian response, characterized by discontinuous shear thickening (DST) and potentially shear jamming (SJ), due to the formation of a frictionally stabilized contact network. Investigating how the molecular weight of the suspending solvent affects the frictional particle-particle interactions, we report on experiments with suspensions of fumed silica particles in polyethylene glycol (PEG). Focusing on the monomer-to-oligomer limit, with n = 1 to 8 ethylene oxide repeat units, we find that increasing n enhances shear thickening under steady-state shear and even elicits rapidly propagating shear jamming fronts, as assessed by high-speed ultrasound imaging of impact experiments. We associate this behavior with a weakening of the solvation layers surrounding the particles as n is increased, which thereby facilitates the formation of frictional contacts. We argue that for n larger than the monomer-to-oligomer limit the trend reverses and frictional interactions are diminished, as observed in prior experiments. This reversal occurs because the polymeric solvent transitions from being enthalpically bound to entropically bound to the particle surfaces, which strengthens solvation layers.

Heat Transfer and Rheological Behavior of Fumed Silica Nanofluids

The addition of nanoparticles to liquid media can improve thermomechanical properties of dispersants. This ability gives rise to the development of multiple applications of nanofluids (NF) in branches so different as electronic and photonic devices or cosmetic industry. Logically, these applications require a good control of heat transfer and flow properties. Moreover, if we consider the necessity to optimize industrial processes in which NF take part, it is necessary to obtain possible relationships between both physical mechanisms. Specifically, in this work, a study about thermal conductivity and rheological behavior of fumed silica suspensions in polypropylene glycol (PPG400) and polyethylene glycol (PEG200) was performed. The study of these two suspensions is interesting because the flow behaviors are very dissimilar (while the fumed silica in PEG200 suspension is viscoplastic, the fumed silica in PPG400 suspension shows shear-thickening behavior between two shear-thinning regions), despite the addition of fumed silica producing similar enhancement of the relative thermal conductivity in both liquid phases. The more outstanding contribution of this work lies in the combination of rheological and conductivity measurements to deepen in the understanding of the heat transfer phenomenon in NF. The combination of rheological together with thermal conductivity measurements have permitted establishing the mechanisms of liquid layering and aggregate formation as the more relevant in the heat transfer of these silica fumed suspensions.

Filament Extrusion and Its 3D Printing of Poly(Lactic Acid)/Poly(Styrene-co-Methyl Methacrylate) Blends

Herein, we report the melt blending of amorphous poly(lactide acid) (PLA) with poly(styrene-co-methyl methacrylate) (poly(S-co-MMA)). The PLAx/poly(S-co-MMA)y blends were made using amorphous PLA compositions from 50, 75, and 90wt.%, namely PLA50/poly(S-co-MMA)50, PLA75/poly(S-co-MMA)25, and PLA90/poly(S-co-MMA)10, respectively. The PLAx/poly(S-co-MMA)y blend pellets were extruded into filaments through a prototype extruder at 195 °C. The 3D printing was done via fused deposition modeling (FDM) at the same temperature and a 40 mm/s feed rate. Furthermore, thermogravimetric curves of the PLAx/poly(S-co-MMA)y blends showed slight thermal decomposition with less than 0.2% mass loss during filament extrusion and 3D printing. However, the thermal decomposition of the blends is lower when compared to amorphous PLA and poly(S-co-MMA). On the contrary, the PLAx/poly(S-co-MMA)y blend has a higher Young’s modulus (E) than amorphous PLA, and is closer to poly(S-co-MMA), in particular, PLA90/poly(S-co-MMA)10. The PLAx/poly(S-co-MMA)y blends proved improved properties concerning amorphous PLA through mechanical and rheological characterization.