Fabrication of high flux and fouling resistant membrane: A unique hydrophilic blend of polyvinylidene fluoride/polyethylene glycol/polymethyl methacrylate

First occurrence and risk assessment of microplastics in enteral nutrition formulas

Occurrence and characteristics of microplastics were evaluated in enteral nutrition formulas, for the first time. A total of 30 samples belonging to 9 brands were analysed. Physical and chemical characteristics of microplastics were identified by stereomicroscopy and micro-raman spectroscopy, respectively. The mean number of microplastics was 45 ± 63 MP/L. Two different shapes of microplastics were detected with fibres (62%) being the most common microplastics followed by fragments (38%). The most common color of microplastics was black (37%) followed by blue (26%), orange (15%), green (7%), red (7%), grey (4%) and multicolor (4%). The length of microplastics ranged from 10 to 2086 μm with an average of 548 ± 526 μm. Estimated mean daily microplastic intake for four different scenarios varied between 24 to 61 and 30 to 76 MPs/day for women and men, respectively. The mean polymer hazard index and microplastic load index levels were calculated as 380 and 1.30, respectively. The results of this study showed that microplastics are prevalent in enteral nutrition products. The presence of polymers with high hazard risk scores in enteral nutrition formulas may pose a risk to the health of patients with special nutritional needs.

Electrically Controlled Adsorptive Membranes with Tunable Affinity for Selective Chromium (VI) Separation from Water

Ionic contaminants such as Cr(VI) pose a challenge for water purification using membrane-based processes. However, existing membranes have low permeability and selectivity for Cr(VI). Therefore, in this study, we prepared an electrically controlled adsorptive membrane (ECAM-L) by coating a loose Cl--doped polypyrrole layer on a carbon nanotube substrate, and we evaluated the performance of ECAM-L for Cr(VI) separation from water. We also used electrochemical quartz crystal microbalance measurements and molecular dynamics and density functional theory calculations to investigate the separation mechanisms. The adsorption and desorption of Cr(VI) could be modulated by varying the electrostatic interactions between ECAM-L and Cr(VI) via potential control, enabling the cyclic use of the ECAM-L without additional additives. Consequently, the oxidized ECAM-L showed high Cr(VI) removal performance (<50 μg/L) and treatment capacity (>3500 L/m2) at a high water flux (283 L/m2/h), as well as reusability after the application of a potential. Our study demonstrates an efficient membrane design for water decontamination that can selectively separate Cr(VI) through a short electric stimulus.

Radiation‐Induced Admicellar Graft Polymerization of 2‐Hydroxyethyl Methacrylate onto Polyvinylidene Fluoride Membranes Using an Electron Beam Accelerator

The efficiency of admicellar graft polymerization in functionalizing polyvinylidene fluoride (PVDF) membranes was explored. The effect of 2‐hydroxyethyl methacrylate (HEMA) concentration and the absorbed dose was investigated using a simultaneous method of radiation‐induced graft polymerization. The degree of grafting increased with raising the absorbed dose and HEMA concentration. The Fourier transform infrared (FTIR) peak for C–O stretch and the asymmetric and symmetric stretching of the C–O–C bridge, respectively, proved the presence of poly(2‐hydroxyethyl methacrylate) (PHEMA) on the modified PVDF. As the grafting yield increased, rougher surfaces were observed. According to contact angle analysis, the grafted membrane with a higher grafting yield outperformed the low grafting yield membrane in terms of water flux and hydrophilicity.

Designing a novel poly (methyl vinyl ether maleic anhydride) based polymeric membrane with enhanced antifouling performance for removal of pentachlorophenol from aqueous solution

In this current study, poly (methyl vinyl ether maleic anhydride) (PMVEAMA), a sustainable additive, was incorporated into poly (ether-ether sulfone) (PEES) polymer to design a novel polymeric hybrid membrane for the efficient filtration of toxic pentachlorophenol (PCP) from an aqueous medium. Hydrophilic additives significantly altered the membrane's morphology, structure, porosity, water content, and flux performance compared to the bare PEES membrane. The influence of PMVEAMA on the structural modification of the synthesized polymer membrane was confirmed by SEM, ATR-FTIR, XRD, AFM, zeta potential and contact angle. Findings revealed that the addition of PMVEAMA to the PEES polymer enhances the porosity (17.7%-28.9%), water content (29.8%-39.8%), and pure water flux (186 Lm^-2h^-1 to 349 Lm^-2h^-1). The effect of PMVEAMA concentration on the PEES membrane exhibited more finger like pores, better porosity and hydrophilicity, reduced surface roughness, fouling and increased permeability. The fouling studies exhibit an improved 57% PCP rejection and permeation flux of 22.3 Lm^-2h^-1 due to the addition of the hydrophilic additive. Surprisingly, the incorporation of PMVEAMA into the bare PEES membrane resulted in a high flux recovery ratio of 73.7%. The antifouling properties and enhanced permeability of the PEES/PMVEAMA membrane indicates its potential application in water purification sectors for the efficient separation of contaminants.

Incorporation of 2D-biotene to polyethersulfone ultrafiltration membrane with superhydrophilicity and antifouling properties for removal of organic pollutants

Here, for the first time, one or few-layer exfoliated 2D-Biotene (E-BIT) was prepared by a cost-effective liquid-phase exfoliation of economical and accessible bulk biotite (B-BIT). The successful preparation of E-BIT was further verified by different characterization methods. XRD pattern demonstrated that B-BIT's basal spacing was increased from 10.07 Å to 11.02 Å. Also, the transparency of the E-BIT to the electron beam showed its small thickness after exfoliation, which was confirmed by AFM results, too. This natural material was utilized as an efficient nano-additive to improve the properties of polyethersulfone (PES) polymeric membrane. E-BIT blended membranes with various quantities (0-2 wt%) were prepared via the non-solvent induced phase inversion method. Small holes at the up layer, coarse finger-like holes and macro-voids at the sublayer were seen in asymmetric prepared membranes. Modification caused the improvement of the membranes' hydrophilicity, which the contact angle was reduced from 69.3 to 53.4 for bare PES and 1 wt% E-BIT blended membranes, respectively. 1 wt% E-BIT blended membrane illustrated flux enhancement of 198.8 L/m² h, and high elimination efficiency of bovine serum albumin (99%), reactive red 195 (97.8%), reactive green 9 (93.5%), and reactive blue 19 (88.4%), with improved flux recovery ratio of 73%.

One-Pot Polymerization of Dopamine as an Additive to Enhance Permeability and Antifouling Properties of Polyethersulfone Membrane

This paper reports the fabrication of polyethersulfone membranes via in situ hydrogen peroxide-assisted polymerization of dopamine. The dopamine and hydrogen peroxide were introduced into the dope solution where the polymerization occurred, resulting in a single-step additive formation during membrane fabrication. The effectivity of modification was evaluated through characterizations of the resulting membranes in terms of chemical functional groups, surface morphology, porosity, contact angle, mechanical strength and filtration of humic acid solution. The results confirm that the polydopamine was formed during the dope solution mixing through peroxide-assisted polymerization as proven by the appearance of peaks associated OH and NH groups in the resulting membranes. The presence of polydopamine residual in the membrane matric enhances the pore properties in terms of size and porosity (by a factor of 10), and by lowering the hydrophilicity (from 69° to 53°) which leads to enhanced filtration flux of up to 217 L/m2 h. The presence of the residual polydopamine also enhances membrane surface hydrophilicity which improve the antifouling properties as shown from the flux recovery ratio of > 80%.