Graft ratio: Quantitative measurement and direct evidence for its blending sequence dependence during reactive compatibilization in PVDF/PLLA

Going beyond Cellulose and Chitosan: Synthetic Biodegradable Membranes for Drinking Water, Wastewater, and Oil-Water Remediation

Membrane technology is an efficient way to purify water, but it generates non-biodegradable biohazardous waste. This waste ends up in landfills, incinerators, or microplastics, threatening the environment. To address this, research is being conducted to develop compostable alternatives that are sustainable and ecofriendly. Bioplastics, which are expected to capture 40% of the market share by 2030, represent one such alternative. This review examines the feasibility of using synthetic biodegradable materials beyond cellulose and chitosan for water treatment, considering cost, carbon footprint, and stability in mechanical, thermal, and chemical environments. Although biodegradable membranes have the potential to close the recycling loop, challenges such as brittleness and water stability limit their use in membrane applications. The review suggests approaches to tackle these issues and highlights recent advances in the field of biodegradable membranes for water purification. The end-of-life perspective of these materials is also discussed, as their recyclability and compostability are critical factors in reducing the environmental impact of membrane technology. This review underscores the need to develop sustainable alternatives to conventional membrane materials and suggests that biodegradable membranes have great potential to address this challenge.

Inclusion/Exclusion Behaviors of Small Molecules during Crystallization of Polymers in Miscible PLLA/TAIC Blend

In this work, PLLA/TAIC has been taken as a model system to investigate the inclusion and exclusion of small molecules during the crystallization of polymers in their miscible blend. Our results indicate that it is the growth rate and diameter of PLLA spherulites that dominate the localization of TAIC. On the one hand, crystallization temperature plays an important role. Crystallization at higher temperature corresponds to higher growth rates and a greater diameter of PLLA spherulites. The former improves the ability of PLLA crystals to trap TAIC while the latter leads to a lower volume fraction of space among neighboring PLLA spherulites. The combination of the two contributes to the enhanced inclusion behaviors. On the other hand, when compared to melt crystallization, cold crystallization results in much smaller spherulites (from higher nucleation density) and sufficient space among spherulites, which accounts for the enrichment of TAIC in interspherulitic regions and for its enhanced exclusion. In the adopted polymer–small molecule blend, TAIC can enrich in interspherulitic regions even in its miscible blend with PLLA, which can be attributed to its stronger diffusion ability.

Improvement of PLLA Ductility by Blending with PVDF: Localization of Compatibilizers at Interface and Its Glycidyl Methacrylate Content Dependency

In this work, the localization of reactive compatibilizer (RC, containing poly(methyl methacrylate) (PMMA) backbone with randomly distributed glycidyl methacrylate (GMA) on it) at the polyvinylidene fluoride/poly(l-lactic acid) (PVDF/PLLA) interface has been manipulated by means of GMA contents. At the very beginning of mixing, RC tends to stay in the PVDF phase due to the miscibility between PVDF and PMMA. Upon further shearing, more and more PLLA chains have been grafted on PMMA backbone, producing PLLA-g-PMMA copolymer. The balanced stress on two sides accounts for the localization of compatibilizers at the PVDF/PLLA interface. Finally, the stress of the PLLA side has been enhanced remarkably due to the higher graft density of PLLA, resulting in the enrichment of the copolymer in the PLLA matrix. The migration of RC from the PVDF phase to the immiscible interface and PLLA matrix can be accelerated by employing RC with higher GMA content. Furthermore, the compatibilizer localization produces a significant influence on the morphology and ductility of the PVDF/PLLA blend. Only when the compatibilizers precisely localize at the interface, the blend exhibits the smallest domain and highest elongation at break. Our results are of great significance for not only the fabrication of PLLA with high ductility, but also the precise localization of compatibilizers at the interface of the immiscible blend.

Reactive Comb Polymer Compatibilized Immiscible PVDF/PLLA Blends: Effects of the Main Chain Structure of Compatibilizer

The compatibilizer with double comb structure has a superior compatibilizing effect for immiscible polymer blends due to the symmetrical structure on both sides of main chains. Extensive study related to the architectural effects of compatibilizer on the compatibilization has mainly focused on the side chains. We investigated the influence of the compatibilizer-main-chain structure on the compatibilizing effect for immiscible poly(vinylidene fluoride)/poly(L-lactic acid) (PVDF/PLLA) blends. Two reactive-comb compatibilizers with polystyrene (PS) and polymethylmethacrylate (PMMA) as main chains and PMMA as the side chains have been synthesized. PS is immiscible with both PLLA and PVDF, while PMMA is miscible with PVDF. It was found that both compatibilizers can improve the compatibility between the PLLA and PVDF, with different compatibilization effects. In the PVDF/PLLA (50/50) blends, 1 wt.% poly(styrene-co-glycidyl methacrylate)-graft-poly(methyl methacrylate) (RC-SG) tuned the morphology from the droplet-in-matrix structure to the co-continuous structure, while the blends with poly(methyl methacrylate-co-glycidyl methacrylate)-graft-poly(methyl methacrylate) (RC-MMG) kept the sea-island structure with even 3 wt.% loading. Moreover, RC-SG induces a wider co-continuous interval range than RC-MMG. The co-continuous structure obtained by RC-SG was also more stable than that by RC-MMG. It was further found that RC-SG-compatibilized PVDF/PLLA blends exhibit higher mechanical properties than the RC-MMG-compatibilized blends.