Influence of particle size on the direct compression of ibuprofen and its binary mixtures

Demonstrating scalability between two blender types using DEM

Powder blending is a critical step in pharmaceutical manufacturing that can impact product quality such as tablet tensile strength. This study utilized the Discrete Element Method (DEM) to investigate blending in a 5-liter mini-batch and a 2-liter Turbula blender. DEM parameters were calibrated using small-scale powder characterization tests, so that the particle behavior in the DEM simulations matches the measured behavior. The research explored the effects of blender designs and process conditions on blending and lubricant dispersion. A predictive model for tablet tensile strength was developed. The model takes the lubricant's dispersion via the lubrication energy into account. The model is then used to predict the tablet tensile strength depending on the chosen process parameters, blending speed, duration, and fill level. DEM simulations enabled scaling between the two blenders, providing valuable insights for a semi-continuous manufacturing process based on mini-batch blending. The findings contribute to a deeper understanding of blending mechanics, offering potential enhancements in pharmaceutical manufacturing efficiency and product consistency.

Understanding the roles of compaction pressure and crystal hardness on powder tabletability through bonding area - Bonding strength interplay

Bonding area (BA) and bonding strength (BS) interplay dictates tensile strength of a tablet and, hence, tabletability. Using a series of alkali halides with mechanical properties spanning more than one order of magnitude, the role of compaction pressure and mechanical properties on tabletability is systematically investigated and explained using the BA-BS interplay. Results reveal that BA dominates the BA-BS interplay at low pressures, where more plastic powders attain higher tensile strength due to larger BA. In contrast, BS dominates the interplay at high pressures, when difference in BA between powders is minimized. Under the typical compaction pressures of 100-300 MPa, tablet tensile strength is the highest for materials with intermediate hardness, or plasticity, due to an optimal BA-BS interplay.

Investigating the heat sensitivity of frequently used excipients with varying particle sizes

During tablet manufacturing an increase in the production temperature can lead to an alteration of tablet characteristics. In the present study, the influence of the initial particle size on the tableting behavior of ductile polymers upon temperature rise was investigated. Different grades of the respective materials were tableted at temperatures ranging from 22 to 70 °C. Alterations in tableting behavior were affected by the initial particle size. Smaller particle sizes led to a more pronounced decrease in yield pressure and net work of compaction during compressibility analysis. The results were confirmed in the tabletability studies. Tablets from binary mixtures with lactose containing smaller polymer particles yielded a stronger increase in tensile strength. Differences in the tensile strength increase of two grades from the same material correlated with the ratio of their median particle sizes. The alteration of compactibility profiles was also particle size dependent. The increase in solid fraction was more prominent for binary mixtures containing polymers with smaller particle sizes. However, the ratio of the median particle sizes of the compared grades showed no systematic effect. The results underline the importance of controlling the structural properties of a material carefully during formulation development and production. If a formulation responds to temperature variations, an increase in particle size might be beneficial to decrease its heat sensitivity.

Reviewing the Impact of Powder Cohesion on Continuous Direct Compression (CDC) Performance

The pharmaceutical industry is undergoing a paradigm shift towards continuous processing from batch, where continuous direct compression (CDC) is considered to offer the most straightforward implementation amongst powder processes due to the relatively low number of unit operations or handling steps. Due to the nature of continuous processing, the bulk properties of the formulation will require sufficient flowability and tabletability in order to be processed and transported effectively to and from each unit operation. Powder cohesion presents one of the greatest obstacles to the CDC process as it inhibits powder flow. As a result, there have been many studies investigating potential manners in which to overcome the effects of cohesion with, to date, little consideration of how these controls may affect downstream unit operations. The aim of this literature review is to explore and consolidate this literature, considering the impact of powder cohesion and cohesion control measures on the three-unit operations of the CDC process (feeding, mixing, and tabletting). This review will also cover the consequences of implementing such control measures whilst highlighting subject matter which could be of value for future research to better understand how to manage cohesive powders for CDC manufacture.

Development of a simple in-die method for determination of capping tendency in rotary tableting machines

A rotary tableting machine is used for the continuous tableting process. Tableting conditions often result in capping, leading to serious problems during production. Several studies have been conducted to predict the tablet capping tendency. However, as most previous studies were conducted using a compaction simulator, there is a lack of technology that can be readily applied during actual production. Therefore, the present study aimed to develop a novel method for predicting tablet capping in a rotary tableting machine. We hypothesized that capping occurs when residual stress of the tablet inside a die exceeds the critical stress immediately before ejection. Residual stress was evaluated by measuring the in-line die-wall pressure in a rotary tableting machine. Additionally, critical stress was estimated from the tablet strength inside the die using the Rumpf's equation. The critical and residual stresses were compared to determine the capping tendency to some extent. The findings of this study will substantially contribute to the rapid detection of tablet capping during tablet production.

Improving the Manufacturability of Cohesive and Poorly Compactable API for Direct Compression of Mini-tablets at High Drug Loading via Particle Engineering

PURPOSE

To utilize a particle engineering strategy to improve the manufacturability of a cohesive and poorly compactable API at high drug loading for direct compression of mini-tablets.

METHODS

A high-shear mixer was used for wet milling during the API manufacturing process to obtain target particle size distributions. The targeted particles were characterized and formulated into blends by mixing with excipients. The formulated blends were compressed directly into mini-tablets using a compaction simulator. The tablet hardness, weight variation, and friability of the mini-tablets were characterized and compared with mini-tablets prepared with hammer milled APIs.

RESULTS

Compared to the hammer milled APIs, the wet milled APIs, had smoother surface, narrower particle size distributions and demonstrated a better flow properties. Moreover, the mini-tablets produced with the wet milled APIs exhibited better weight uniformity, robust tablet mechanical strength and ultimately better friability. In addition, unlike the hammer milled process, the wet milling process is controllable and easy to scale up.

CONCLUSIONS

This study successfully implemented API particle engineering through a high shear wet milling process to produce particles suitable for robust drug product manufacturing.

Influence of the drug deformation behaviour on the predictability of compressibility and compactibility of binary mixtures

Various studies investigate the predictability of the compressibility and compactibility of tablet formulations based on the behaviour of the pure materials. However, these studies are limited to a few materials so far probably because of the complexity of the powder compaction process. One approach preventing the excessive increase in complexity is the extension of the investigations from pure materials to binary powder mixtures. The focus of this study is on the predictability of the compressibility and compactibility of binary mixtures consisting of an active pharmaceutical ingredient (API) and the excipient microcrystalline cellulose. Three APIs with markedly different deformation behaviour were used. The API concentration and type are systematically varied. For all three material combinations it is found that the in-die compressibility of the binary mixtures can be precisely predicted based on the characteristic compression parameters of the raw materials using the extended in-die compression function in combination with a volume-based linear mixing rule. Since the tablet porosity (out-of-die) also follows a linear mixing rule, the predictability can be further extended using the method of Katz et al. In contrast, the influence of the API concentration on compactibility or rather on tablet tensile strength is non-linear and strongly dependent on the deformation behaviour of the API, making the predictability more difficult. Neither the approach of Reynolds et al. nor this of Kuentz and Leuenberger are able to predict the compactibility when clear deviations from a linear mixing rule appear.

Tableting model assessment of porosity and tensile strength using a continuous wet granulation route

This paper presents a comprehensive assessment of the most widely used tablet compaction models in a continuous wet granulation tableting process. The porosity models, tensile strength models and lubricant models are reviewed from the literature and classified based on their formulations i.e. empirical or theoretical and applications, i.e. batch or continuous. The majority of these models are empirical and were initially developed for batch tabletting process. To ascertain their effectiveness and serviceability in the continuous tableting process, a continuous powder processing line of Diamond Pilot Plant (DiPP) installed at The University of Sheffield was used to provide the quantitative data for tablet model assessment. Magnesium stearate (MgSt) is used as a lubricant to investigate its influence on the tensile strength. Whilst satisfactory predictions from the tablet models can be produced, a compromise between the model fidelity and model simplicity needs to be made for a suitable model selection. The Sonnergaard model outperforms amongst the porosity models whilst the Reynolds model produces the best goodness of fitting for two parameters fitting porosity models. An improved tensile strength model is proposed to consider the influence of powder size and porosity in the continuous tableting process.

The influence of particle size on the application of compression and compaction models for tableting

The physical characteristics of raw materials determine powder compression and compaction performance as relevant in pharmaceutical processes. For instance, the influence of initial particle size on powder compression and the resulting strength of specimen are highly complex and are still not sufficiently understood. Existing studies are often limited to materials with well-defined deformation behaviour, such as purely brittle or ductile. However, the deformation behaviour of active pharmaceutical ingredients (APIs) is often more complex. In this study, the influence of initial particle size on powder compressibility and compactibility is systematically characterized by consideration of in-die compressibility, specific energies, quick elastic recovery, tablet porosity and, tensile strength for the binder microcrystalline cellulose and three APIs. The decrease of particle size leads to an increase of the resistance against compression by trend and probably to a different contribution of the acting deformation mechanisms. The compactibility is increased with decreasing particle size because of the increasing number of bonds in a cross-sectional area of the tablet, as found by the application of the model of Rumpf. Furthermore, it is found that the model of Rumpf combined with the JKR model provides a meaningful property function to estimate tablet tensile strength.

It is Possible to Achieve Tablets With Good Tabletability From Solid Dispersions - The Case of the High Dose Drug Gemfibrozil

BACKGROUND

Solid Dispersions (SDs) have been extensively used to increase the dissolution of poorly water-soluble drugs. However, there are few studies exploring SDs properties that must be considered during tablet development, like tabletability. Poorly water-soluble drugs with poor compression properties and high therapeutic doses, like gemfibrozil, are an additional challenge in the production of SDs-based tablets.

OBJECTIVE

This study evaluates the applicability of SDs to improve both tabletability and dissolution rate of gemfibrozil. A SD-based tablet formulation was also proposed.

METHODS

SDs were prepared by ball milling, using hydroxypropyl methylcellulose (HPMC) as a carrier, according to a 2³ factorial design. The formulation variables were gemfibrozil:HPMC ratio, milling speed, and milling time. The response in the factorial analysis was the tensile strength of the compacted SDs. Dissolution rate and solid-state characterization of SDs were also performed.

RESULTS

SDs showed simultaneous drug dissolution enhancement and improved tabletability when compared to corresponding physical mixtures and gemfibrozil. The main variable influencing drug dissolution and tabletability was the gemfibrozil:HPMC ratio. Tablets containing gemfibrozil- HPMC-SD (1:0.250 w/w) and croscarmellose sodium showed fast and complete drug release, while those containing the same SD and sodium starch glycolate exhibited poor drug release due to their prolonged disintegration time.

CONCLUSION

SDs proved to be effective for simultaneously improving tabletability and dissolution profile of gemfibrozil. Tablets containing gemfibrozil-HPMC-SD and croscarmellose sodium as disintegrating agent showed improved drug release and good mechanical strength, demonstrating the potential of HPMC-based SDs to simultaneously overcome the poor dissolution and tabletability properties of this drug.

The Shielding Effect of Microcrystalline Cellulose on Drug Nanocrystal Particles During Compaction

To elucidate the compaction behavior of drug nanocrystals based composite particles (NP) during tabletting, the compaction behavior of binary mixtures of microcrystalline cellulose (MCC) and nanocrystal particles was investigated. The force-displacement correlation of mixtures containing different ratios of MCC and micronized NP was studied in order to explain the nature on densification of NP during compaction, and the resultant compaction curves (pressure as function of in-die thickness) were systemically analyzed to elucidate the most important mechanisms of volume reduction for MCC and NP in different stages of compaction. The results showed that the close compaction of individual MCC was relatively quickly achieved, and the drug NP particles could slide into the intrinsic void spaces between MCC microparticles. This was the reason that the particles size of MCC used in this study was significantly larger compared to that of drug NP. This interstitial rearrangement phenomenon of NP occurred on a typical time scale and was strongly dependent on the speed of compaction. This migration behavior occurred on void spaces of MCC inter-particles might be identified as an elastic stress relaxation mechanism and be helpful to dissolution of NP. MCC can effectively shield the NP from significant aggregation during compaction process.