Synthesis and characterization of nesquehonite (MgCO3·3H2O) powders from natural talc

Reconstruction of Highly-Defective MgO and Exceptional Photochemical Activity on CO2 Upgrade in Aqueous Solution

Defects on metal oxide have attracted extensive attention in photo-/electrocatalytic CO2 reduction. Herein, porous MgO nanosheets with abundant oxygen vacancies (Vo s) and three-coordinated oxygen atoms (O3c ) at corners are reported, which reconstruct into defective MgCO3 ·3H2 O exposing rich surface unsaturated -OH groups and vacancies to initiate photocatalytic CO2 reduction to CO and CH4 . In consecutive 7-cycle tests (each run for 6 h) in pure water, CO2 conversion keeps stable. The total production of CH4 and CO attains ≈367 µmol gcata -1 h-1 . The selectivity of CH4 gradually increases from ≈3.1% (1st run) to ≈24.5% (4th run) and then remains unchanged under UV-light irradiation. With triethanolamine (3.3 vol.%) as the sacrificial agent, the total production of CO and CH4 production rapidly increases to ≈28 000 µmol gcata -1 in 2 h reaction. Photoluminescence spectra reveal that Vo s induces the formation of donor bands to promote charge carrier seperation. A series of trace spectra and theoretical analysis indicate Mg-Vo sites in the derived MgCO3 ·3H2 O are active centers, which play a crucial role in modulating CO2 adsorption and triggering photoreduction reactions. These intriguing results on defective alkaline earth oxides as potential photocatalysts in CO2 conversion may spur some exciting and novel findings in this field.

Biomineralization of Carbonates Induced by Mucilaginibacter gossypii HFF1: Significant Role of Biochemical Parameters

Although the precipitation of carbonate minerals induced by various bacteria is widely studied, the changes in the biochemical parameters, and their significant role in the biomineralization processes, still need further exploration. In this study, Mucilaginibacter gossypii HFF1 was isolated, identified, and used to induce carbonate minerals at various Mg/Ca ratios. The biochemical parameters were determined in order to explore the biomineralization mechanisms, including cell concentration, pH, ammonia, carbonic anhydrase activity, and alkaline phosphatase activity. The characteristics of extracellular minerals and intracellular inclusions were both analyzed. In addition, the amino acid composition of the extracellular polymeric substance was also tested. Results show that the biochemical parameters provide an alkaline environment for precipitation, due to the combined effect of ammonia, carbonic anhydrase, and alkaline phosphatase. Biotic minerals are characterized by preferred orientation, specific shape, and better crystalline and better thermal stability, indicating their biogenesis. Most of the amino acids in the extracellular polymeric substance are negatived charged, and facilitate the binding of magnesium and calcium ions. The particles with weak crystalline structure in the EPS prove that it acts as a nucleation site. Intracellular analyses prove the presence of the intracellular amorphous inclusions. Our results suggest that the changes in the biochemical parameters caused by bacteria are beneficial to biomineralization, and play a necessary role in its process. This offers new insight into understanding the biomineralization mechanism of the bacteria HFF1.

Evolution of Black Talc upon Thermal Treatment

Black talc is a natural silicate clay mineral with a typical 2:1 layered structure, low electrical conductivity, large specific surface area, and high thermal stability. The world’s largest black talc mine, with known reserves of one billion tons, is located in China’s Jiangxi province. Due to the restriction of its color, the application of black talc is only limited to ceramic raw materials, coating filler, waterproof materials, and other low-end application industries. Thermal treatment is a common method of clay mineral modification. It is vital to examine the structural and physical changes of black talc during calcination in order to prepare black-talc-based composites and to broaden their applications. This work discusses the evolution of black talc upon thermal treatment (30–1000 °C) and the corresponding structural changes. The thermal stability of minerals was analyzed via thermogravimetric (TG) analysis and thermogravimetry–mass spectrometry (TG-MS). The decomposition of minerals during calcination consists of four processes: dehydration, organic carbon decomposition, dihydroxylation, and phase transformation. In situ FTIR and in situ XRD were employed to track changes in black talc in real time during thermal treatment. At 800 °C, black talc was found to begin to go through dihydroxylation, and the crystallinity index decreased significantly. The XRD pattern of samples at 950 °C (T950) showed the reflection of the enstatite structure, and the relative crystallinity index was 27.3%, indicating that the mineral had undergone phase transformation. In addition, the Brunauer–Emmet–Teller (BET), laser particle size analyzer, Zeta potential, scanning electron microscopy (SEM), and transmission electron microscopy (TEM) techniques were used to systematically characterize the physicochemical properties of minerals at different temperatures. The results show that black talc’s particle size and specific surface area increase with the calcination temperature. The surface charge changes, and more amorphous SiO2 and MgO appear, indicating that thermal treatment could induce structural changes and activate the surface of black talc.

Synthesis of magnesium carbonate hydrate from natural talc

Various morphologies of magnesium carbonate hydrate had been synthesized without using any organic additives by carefully adjusting the reaction temperature and time during the talc carbonation process. At lower temperatures, magnesium carbonate hydrate was prone to display needle-like morphology. With the further increase of the carbonation temperature, the sheet-like crystallites became the preferred morphology, and at higher aging temperatures, these crystallites tended to assemble into layer-like structures with diverse morphologies, such as rose-like particles and nest-like structure. The reaction time had no effect on the crystal morphology, but it affected the particle size and situation of the crystal growth. X-Ray diffraction results showed that these various morphologies were closely related to their crystal structure and compositions. The needle-like magnesium carbonate hydrate had a formula of MgCO3·3H2O, whereas with the morphological transformation from needle-like to sheet-like, rose-like, and nest-like structure, their corresponding compositions also changed from MgCO3·3H2O to 4MgCO3·Mg(OH)2·8H2O, 4MgCO3·Mg(OH)2·5H2O, and 4MgCO3·Mg(OH)2·4H2O.

Synthesis of MgO micro-rods coated with charred dextrose and its application for the adsorption of selected heavy metals from synthetic and real groundwater

MgO micro-rods supported on porous carbon were synthesized by an economical method and applied for the adsorption of three different heavy metals ions (As (III), Cd (II) and Pb (II)). Here, we used dextrose as the source of carbon during the synthesis. The synthesized material has been characterized by different techniques like XRD, TEM, FE-SEM, BET and FT-IR for the determination of various physical properties. Compared with MgO synthesized without dextrose, the carbon-supported MgO or C-MgO demonstrated consistent rod-shaped morphology, higher surface area and better absorptivity. The adsorption data were analysed using various isotherm models and the Freundlich isotherm model seemed to provide the best fit to the data. The adsorption kinetics data on the other hand was well explicated by the pseudo second-order kinetic model. The maximum adsorption capacity of C-MgO was 508.47 mg g^-1 for As (III), 566.01 mg g^-1 for Cd (II) and 476.19 mg g^-1 for Pb (II), respectively after 6 h of reaction. To check the real-life usability and efficiency of C-MgO, it was added to a groundwater sample which had 169.55 ppb of As (III) and within 20 min it was adsorbed with 99% efficiency. Reusability studies reveal that C-MgO could be used up to 6 times with more than 60% efficiency. This study shows that C-MgO has high adsorptive ability, is an economic and non-toxic material with versatile applications and can be used for groundwater remediation in real life.

S. Nellaiappan SN. Improving the corrosion resistance and bioactivity of magnesium by a carbonate conversion-polycaprolactone duplex coating approach

Decreasing the rate of degradation of Mg has been the focus of developing magnesium carbonate-polycaprolactone duplex coatings for Mg.

Pd Nanoparticles and MOFs Synergistically Hybridized Halloysite Nanotubes for Hydrogen Storage

Natural halloysite nanotubes (HNTs) were hybridized with metal-organic frameworks (MOFs) to prepare novel composites. MOFs were transformed into carbon by carbonization calcination, and palladium (Pd) nanoparticles were introduced to build an emerging ternary compound system for hydrogen adsorption. The hydrogen adsorption capacities of HNT-MOF composites were 0.23 and 0.24 wt%, while those of carbonized products were 0.24 and 0.27 wt% at 25 °C and 2.65 MPa, respectively. Al-based samples showed higher hydrogen adsorption capacities than Zn-based samples on account of different selectivity between metal and hydrogen and approximate porous characteristics. More pore structures are generated by the carbonization reaction from metal-organic frameworks into carbon; high specific surface area, uniform pore size, and large pore volume benefited the hydrogen adsorption ability of composites. Moreover, it was also possible to promote hydrogen adsorption capacity by incorporating Pd. The hydrogen adsorption capacity of ternary compound, Pd-C-H3-MOFs(Al), reached 0.32 wt% at 25 °C and 2.65 MPa. Dissociation was assumed to take place on the Pd particles, then atomic and molecule hydrogen spilled over to the structure of carboxylated HNTs, MOFs, and the carbon products for enhancing the hydrogen adsorption capacity.

Tin Oxide-Carbon-Coated Sepiolite Nanofibers with Enhanced Lithium-Ion Storage Property

Natural sepiolite (Sep) nanofibers were coated with carbon and nanoscale SnO2 to prepare an emerging nanocomposite (SnO2-C@Sep), which exhibited enhanced electrochemical performance. Sepiolite could act as a steady skeleton, carbon coating principally led sepiolite from an isolated to an electric state, and decoration of nanoscale SnO2 was beneficial to the functionization of sepiolite. Cycling performances indicated that SnO2-C@Sep showed higher discharge capacities than commercial SnO2 after 50 cycles. The nanocomposite SnO2-C@Sep possessed enhanced lithium storage properties with stable capacity retention and low cost, which could open up a new strategy to synthesize a variety of functional hybrid materials based on the cheap and abundant clay and commercialization of lithium-metal oxide batteries.

Structure and Electronic Properties of Transition Metal Doped Kaolinite Nanoclay

In this work, a series of transition metal (Cr, Mn, Fe, and Co) doped kaolinite nanoclays were investigated by density functional theory (DFT) calculations. The influence of metal doping on geometric structure and electronic structure of kaolinite was analyzed. The ferromagnetic (FM), antiferromagnetic (AFM), and nonmagnetic (NM) states of transition metal (TM) doped kaolinite structures were studied. The crystal volume, lattice parameters, bond length, charge, and spin were calculated by dispersion-corrected density functional theory (DFT-D2). The results indicated that Cr³⁺ and Fe³⁺ dopants showed more stable under AFM state, while Mn³⁺ preferred both AFM and FM states, and Co³⁺ dopant preferred NM state. Also, the transition metal doping could induce lattice volume expansion and some dopant states in the band gap.

Lithium orthosilicate with halloysite as silicon source for high temperature CO2 capture

Lithium orthosilicate (Li₄SiO₄)-based sorbents were synthesized using a low cost and naturally available mineral resource (halloysite) as silicon source for high temperature CO₂ capture.

Sepiolite supported stearic acid composites for thermal energy storage

In this paper, novel composite phase change materials (PCMs) were prepared by absorbing stearic acid (SA) into sepiolite (α-sepiolite, β-sepiolite) via a vacuum impregnation method.

Y2O3 functionalized natural palygorskite as an adsorbent for methyl blue removal

The methyl blue adsorption isotherm on Y₂O₃/Palygorskite obeys the Langmuir model, with the maximum adsorption capacity greatly enhanced to 1579.06 mg g⁻¹, exhibiting potential applications in wastewater treatment.