Characterisation of 32 P beta source for external radiation protection

Surface dose rate variations in planar and curved geometries of 106Ru/106Rh plaque sources for ocular tumors

PURPOSE

Investigation of surface dose rate variation with respect to the source configuration of ¹⁰⁶Ru/¹⁰⁶Rh eye plaque. To explore an alternate way to determine activity of brachytherapy plaques.

METHODS

The surface dose rates of ¹⁰⁶Ru/¹⁰⁶Rh plaque developed indigenously were measured by extrapolation chamber. To rule out possibility of any error in the activity distribution and quantity, same source was used in two different configurations namely planar and curved. EBT3 Gafchromic film was used for determination of uniformity in activity. Monte Carlo-based Codes EGSnrc and FLUKA were used to calculate dose rate in tissue, percentage depth dose and for determination of activity. Parameters and correction factors were estimated using simulations.

RESULTS

The measured reference absorbed dose rates for planar and curved ¹⁰⁶Ru/¹⁰⁶Rh eye plaques are found to be 589 ± 29 mGy/h and 560 ± 28 mGy/h, respectively. The difference in the reference absorbed dose rate of curved eye plaque is about ~5% as compared to planar configuration. The FLUKA-calculated dose values are almost independent of cavity length of the extrapolation chamber for both eye plaques. The FLUKA-based dose rates per μCi ¹⁰⁶Ru/¹⁰⁶Rh are about 17.28 ± 0.08 mGy/h and 16.48 ± 0.06 mGy/h, respectively for planar and curved eye plaques which match well with the measurements. The calculated activities for planar and curved eye plaques are 34.08 μCi and 33.98 μCi, respectively.

CONCLUSIONS

Surface dose rates for a prototype ¹⁰⁶Ru/¹⁰⁶Rh eye plaque with different configurations were estimated using simulations and measured experimentally. An alternate way to determine activity of beta-gamma brachytherapy plaque has been proposed.

MEASUREMENT OF OPERATIONAL QUANTITIES Hp(0.07) AND Hp(3) FOR INDIGENOUSLY DEVELOPED 106Ru/106Rh SOURCE USING AN EXTRAPOLATION CHAMBER

In the present study, a prototype 106Ru/106Rh source was fabricated using high level liquid waste from reactor fuel, fixed in a stainless steel housing with a window and backing made of silver. The study involves measurement of the operational quantities Hp(0.07), Hp(3) and the percentage depth dose (PDD) using an extrapolation chamber. It also involves determination of necessary correction factors to arrive at Hp(0.07) and Hp(3) following International Organisation for Standardisation (ISO) and methods suggested in literature. The study facilitates incorporation of the 106Ru/106Rh source as a beta reference source for quality assurance programme in TLD personnel monitoring as per the guidelines of ISO.

Dosimetry of indigenously developed 177Lu patch source for surface brachytherapy-Experimental and Monte Carlo methods

This paper describes the evaluation of dosimetry characteristics of an in-house developed ¹⁷⁷Lu skin patch source for treatment of non-melanoma skin cancer. A ¹⁷⁷Lu skin patch source based on Nafion-115 membrane backbone containing 3.46 ± 0.01 mCi of activity was used. Activity measurement of the patch source was based on gamma ray spectrometry using a HPGe detector. The efficiencies of the HPGe detector were fitted using an orthogonal polynomial function. The absorbed dose rate to water at 5 μm depth in water was determined using an extrapolation chamber, EBT3 Gafchromic film and compared with Monte Carlo methods. The correction factors such as Bragg-Gray stopping power ratio of water-to-air and chamber wall material being different from water, needed to be applied on measurements for establishing the dose rate at 5 μm depth, were calculated using the Monte Carlo method. Absorbed dose rate at 5 μm depth in water (surface dose rate) measured using an extrapolation chamber and EBT3 Gafchromic film were 9.9 ± 0.7 and 8.2 ± 0.1 Gy h^-1 mCi^-1 respectively for the source activity of 3.46 ± 0.01 mCi. The surface dose rate calculated using the Monte Carlo method was 8.7 ± 0.2 Gy h^-1 mCi^-1, which agrees reasonably well with measurement. The measured dose rate per mCi offers scope for ascertaining treatment time required to deliver the dose for propitious therapeutic outcome. Additionally, on-axis depth dose and lateral dose profiles at 5 μm and 1 mm depth in water phantom were also calculated using the Monte Carlo method.