Radiation-induced synthesis of Fe-doped TiO2: Characterization and catalytic properties

Titanium industrial residues surface modification towards its reuse as antimicrobial surfaces

In this study, a new material obtained from titanium ingots residue was coated with natural carotenoids having antibacterial properties. The waste is a no recycling titanium scrap from technological production process which was pressed and transformed into disks titanium samples. Through anodization and annealing procedures of the titanium disk, a nanostructured titanium dioxide surface with photocatalytic and antibacterial properties was successfully obtained. The titanium scrap impurities (V, Al, and N), unwanted for production process, have shown to improve electrochemical and semiconductor properties of the residue surfaces. The nanostructured titanium scrap surface was modified with two different carotenoids, torularhodin and β-carotene, to potentiate the antibacterial properties. The bactericidal tests were performed against Salmonella typhimurium and Escherichia coli, both Gram-negative. The best bactericidal effect is obtained for nanostructured titanium scrap disks immersed in torularhodin, with a percentage of growth inhibition around 60% against both tested bacteria. The results suggest that this low-cost waste material is suitable for efficient reuse as antibacterial surface after a few simple and inexpensive treatments.

Preparation and surface engineering of CM-β-CD functionalized Fe3O4@TiO2 nanoparticles for photocatalytic degradation of polychlorinated biphenyls (PCBs) from transformer oil

The aim of the present research is to investigate the efficiency of surface-modified magnetic nanoparticles for photocatalytic degradation of PCBs from transformer oil. Therefore, CMCD-Fe₃O₄@TiO₂ was successfully produced via grafting of carboxymethyl-β-cyclodextrin (CM-β-CD) onto the core-shell titania magnetic nanoparticles surface. The photocatalytic efficiency of CMCD-Fe₃O₄@TiO₂ for degradation of PCBs was systematically evaluated using an experimental design and the process parameters were optimized by response surface methodology (RSM). The central composite design (CCD) with four experimental parameters was used successfully in the modeling and optimization of photocatalytic efficiency in removing PCBs from transformer oil. ANOVA analysis confirmed a high R-squared value of 0.9769 describing the goodness of fit of the proposed model for the significance estimation of the individual and the interaction effects of variables. The optimal degradation yields of PCBs was achieved 83 % at a temperature of 25 °C, time of 16 min, the dosage of the catalyst of 8.35 mg and oil: ethanol ratio of 1:5. These findings encourage the practical use of CM-β-CD-Fe₃O₄@TiO₂ as a promising and alternative photocatalyst on an industrial scale for the cleaning of organic pollutants such as PCBs due to its environmental friendliness, the benefit of magnetic separation and good reusability after five times.

pH-Control as a way to fine-tune the Cu/Cu2O ratio in radiation induced synthesis of Cu2O particles

In this work we have optimized the γ-radiation induced synthesis of Cu-Cu2O particles from aqueous CuSO4 solution by investigating the effect of pH. The obtained precipitate was analyzed by XRD and SEM techniques. The results indicated that at solution pH lower than 3.75, quasi-spherical Cu agglomerates can be formed while at pH higher than 4.40 only octahedron-shaped Cu2O particles are produced. At solution pH in the range from 3.75 to 4.40, a Cu-Cu2O mixture is produced. It was found that the relative amount of Cu2O in the Cu-Cu2O precipitate increases with pH in the studied range. The influence of solution pH on the Cu/Cu2O ratios in the product can be explained on the basis of pH-dependent competition kinetics between the reactions leading to either Cu or Cu2O formation. As a consequence, the composition and morphology of the Cu-Cu2O precipitate can be tuned by controlling pH of the aqueous CuSO4 solution during the γ-radiation induced synthesis.

Efficient visible light-driven in situ photocatalytic destruction of harmful alga by worm-like N,P co-doped TiO2/expanded graphite carbon layer (NPT-EGC) floating composites

Preparation of N,P co-doped TiO₂/expanded graphite carbon layer (NPT-EGC) composites for floating algaecides.

The Application of Nano-TiO2 Photo Semiconductors in Agriculture

Nanometer-sized titanium dioxide (TiO₂) is an environmentally friendly optical semiconductor material. It has wide application value in many fields due to its excellent structural, optical, and chemical properties. The photocatalytic process of nano-TiO₂ converts light energy into electrical or chemical energy under mild conditions. In recent years, the study and application of nano-TiO₂ in the agricultural sector has gradually attracted attention. The nano-TiO₂ applications of degrading pesticides, plant germination and growth, crop disease control, water purification, pesticide residue detection, etc. are good prospects. This review describes all of these applications and the research status and development, including the underlying principles, features, comprehensive applications, functional modification, and potential future directions, for TiO₂ in agriculture.