Influence of ionizing radiation on the mechanical properties of BisGMA/TEGDMA based experimental resin

Effect of Ionizing Radiation on the Mechanical Properties of Two Dental Materials Commonly Used in Primary Teeth

Aim

The purpose of this in vitro study was to evaluate the effect of radiotherapy on flexural strength, microhardness, and surface roughness of bulk fill composite (X-tra fil) and glass ionomer (EQUIA Forte HT).

Materials and methods

A total of 40 specimens were prepared for each test and were divided into two groups according to the material used (composite or glass ionomer cement), and each group was divided into two subgroups (n = 10) according to radiation condition, irradiated subgroup, subjected to 50 Gy by multienergy linear accelerator delivered in one shot and control subgroup.

Results

Control samples of flexural strength and microhardness had a significantly higher value than irradiated samples in both materials. Regarding the surface roughness, irradiated samples had a significantly higher value than the control samples in both materials.

Conclusion

Irradiation with a linear accelerator had a negative impact on the flexural strength and microhardness of both materials. Moreover, it increased the surface roughness for both materials. Bulk fill composite is the dental restorative material of choice in head and neck cancer patients undergoing radiotherapy due to its high mechanical properties before and after radiation.

How to cite this article

Nagi BM, El-Korashy DI, Amin A El-S, et al. Effect of Ionizing Radiation on the Mechanical Properties of Two Dental Materials Commonly Used in Primary Teeth. Int J Clin Pediatr Dent 2023;16(5):758-762.

Radiation stability of phosphine oxide functionalized pillar[5]arenes

The radiation stability of three phosphine oxide functionalized pillar[5]arenes (POP5A) was studied by an electron accelerator with dose up to 5 MGy in air at room temperature. The structures of both irradiated and unirradiated pillar[5]arenes samples were comparatively characterized by Micro-FTIR, NMR, UV-vis, ESI-HRMS and HPLC techniques. The results revealed different degrees of radiation damage at different doses for POP5A, and the degradation products are mainly composed of organic species containing hydroxyl groups and carbonyl groups. The possible radiolytic degradation pathway was proposed. In addition, extraction of uranyl ion with irradiated POP5A samples was examined. The distribution ratio of uranyl ion was found to increase at low radiation dose and decrease until 3000 kGy. This is the first time that the irradiation stability of pillar[5]arenes derivative extractants has been studied in detail and it provides reliable data support for further application of pillar[5]arenes extractants in practical applications.

Chemical and Mechanical Properties of Experimental Dental Composites as a Function of Formulation and Postcuring Thermal Treatment

This study evaluated the influence of formulation and thermal treatment on the degree of conversion, fracture toughness, flexural strength, and elastic modulus of experimental composites. Six composites were analyzed at BisGMA : TEGDMA molar ratios of 1 : 1 and 7 : 3 with filler at 30, 50, and 70 wt%. The degree of conversion was analyzed by Fourier transform infrared spectroscopy, fracture toughness was measured using the single-edge notched beam, and flexural strength and elastic modulus were measured with the 3-point bend test. For all tests, one-half of the specimens received thermal treatment at 170°C for 10 min. Data were analyzed by the Kruskal-Wallis or ANOVA/Tukey's test (α = 5%). The 1 : 1 BisGMA : TEGDMA ratio showed higher properties than the 7 : 3 ratio. Although the material with 70% filler had a conversion lower than the one with 50%, it showed higher mechanical properties. The thermal treatment improved all properties in all materials. Therefore, the use of an equimolar ratio of BisGMA : TEGDMA can be paired with 70 wt% filler to design dental composites that possess increased advantageous physical and chemical properties. Furthermore, the simple and low-cost method of thermal treatment proposed for use in clinical dentistry has been shown to effectively improve the properties of all evaluated materials.

Correlating cytotoxicity to elution behaviors of composite resins in term of curing kinetic

Cytotoxicity of photocurable composite resins is a key issue for their safe use in dental restoration. Curing kinetic and elution behaviors of the composite resin would have decisive effects on its cytotoxicity. In this study, composite resins composed of bisphenol-glycidyl dimethacrylate (Bis-GMA), triethyleneglycol dimethacrylate (TEGDMA), camphorquinone (CQ), N,N-dimethylaminoethyl methacrylate (DMAEMA) and barium glass powders were prepared by setting the photoinitiators CQ/DMAEMA at 0.5wt%, 1wt% or 3wt% of the total weight of Bis-GMA/TEGDMA. The ratio of Bis-GMA/TEGDMA was 6:4, the ratio of CQ/DMAEMA was 1:1, and the incorporated inorganic powder was 75wt%. Then, curing kinetics were studied by using real-time Fourier transform infrared spectroscopy (FTIR) and photo-DSC (differential scanning calorimeter). Elution behaviors in both ethanol solution and deionized water were monitored by using liquid chromatogram/mass spectrometry (LC/MS). Cytotoxicity was evaluated by in vitro culture of L929 fibroblasts. Finally, they were all analyzed and correlated in terms of initiator contents. It was found that the commonly used 0.5wt% of photoinitiators was somewhat insufficient in obtaining composite resin with low cytotoxicity.