One-pot solvothermal synthesis of robust ambient-dried polyimide aerogels with morphology-enhanced superhydrophobicity for highly efficient continuous oil/water separation

Mechanically Robust and Flexible GO/PI Hybrid Aerogels as Highly Efficient Oil Absorbents

Herein, mechanically robust and flexible graphene oxide/polyimide (GO/PI) hybrid aerogels (GIAs) were fabricated by a facile method, in which the mixed suspensions of the water-soluble polyimide precursor and graphene oxide (GO) sheets were freeze-dried, which was followed by a routine thermal imidation process. The porous GIAs obtained not only exhibit excellent elasticity and extremely low density values (from 33.3 to 38.9 mg.cm^-3), but they also possess a superior compressive strength (121.7 KPa). The GIAs could support a weight of up to 31,250 times of its own weight, and such a weight-carrying capacity is much higher than that of other typical carbon-based aerogels. Having such a porous structure, and high strength and toughness properties make GIAs ideal candidates for oil spill cleanup materials. The oil/organic solvents' absorption capacity ranges from 14.6 to 85, which is higher than that of most other aerogels (sponges). With their broad temperature tolerance and acidic stability, the unique multifunctional GIAs are expected to further extend their application range into extreme environments.

Recent advances in tailoring and improving the properties of polyimide aerogels and their application

With the rapid advancements in technology and growing aerospace applications, there is a need for effective low-weight and thermally insulating materials. Aerogels are known for their ultra-lightweight and they are highly porous materials with nanopores in a range of 2 to 50 nm with very low thermal conductivity values. However, due to hygroscopic nature and brittleness, aerogels are not used commercially and in daily life. To enhance the mechanical and hydrophobic properties, reinforcement materials such as styrene, cyanoacrylates, epoxy along with hydroxyl, amines, vinyl groups are added to the surface. The addition of organic materials resulted in lower service temperatures which reduce its potential applications. Polyimides (PI) are commonly used in engine applications due to their suitable stability at high temperatures along with excellent mechanical properties. Previous research on polyimide aerogels reported high flexibility or even foldability. However, those works' strategy was mainly limited to altering the backbone chemistry of polyimide aerogels by changing either the monomer's compositions or the chemical crosslinker. This work aims to summarize, categorize, and highlight the recent techniques for improving and tailoring properties of polyimide aerogels followed by the recent advancements in their applications.

Ionic liquid-modified polyimide membranes with in-situ-grown polydopamine for separation of oil–water emulsions

Leakage of oily industrial waste is not only a serious environmental and ecological hazard but also poses a significant health risk to people. Membrane separation, which is cost-effective and efficient, is one of the best solutions for reducing pollution discharge through oil–water separation. In this study, polydopamine (PDA) was incorporated into electrostatically spun ionic liquid-capped polyimide (IL-PI) membranes through an in situ growth method; the membranes exhibited the strong adsorption properties of PDA. The polyimide fibers were hydrophilically modified with an IL, which contains several hydrophilic groups, and PDA. Adjusting the polymerization time resulted in the formation of a composite membrane, which could effectively separate oil–water emulsions. Scanning electron microscopy analysis showed that with an increase in the PDA coating time, the PDA content in and on the surface of the composite membrane fibers significantly increased. In addition, the surface contact angle of the membrane decreased from 72.87° to 12.06° with the addition of the PDA coating, while the wettability was significantly improved. The PDA-modified fibrous membranes showed good separation of the emulsified oil–water mixtures. The maximum membrane flux and separation efficiency achieved was 280 L·m−2·h−1 and >99%, respectively. After 10 repeated cycles, the separation efficiency was maintained at >92%. This approach can be used for the design of future wastewater treatment solutions.

Polyimide based super-wettable membranes/materials for high performance oil/water mixture and emulsion separation: A review

This article reviews the application of highly heat and pressure resistant polyimide material for the development of membranes/materials that exhibit unique super-wettability, the characteristics pivotal for the efficient separation of oil-water mixture and emulsion. The polymerization of imide monomer in polyimide brings about the required porosity in the material, which in turn renders the crucial surface roughness, which is instrumental for establishing the desired super-wettability on the polyimide based membrane materials, in addition to the mechanical and thermal robustness. The membrane as the oil-water filtering medium can be either oil passing or water passing depends on the individual wettability of the membrane surface for oil and water, which in turn depend on the respective solid-liquid interfacial energy and the hierarchical surface roughness. Superhydrophobic/superoleophobic wetting characteristic of the surface repels water and allows oil to pass through the membrane medium, and the major disadvantage of this kind of oil/water separation is the rapid oil fouling of the membrane pores and the consequent less efficiency for oil water separation. On the other hand, the membrane surface engineered to have the Superhydrophilic/underwater superoleophobic wetting characteristics can be water passing, and the easy fouling of the membrane surface can be minimized. In the case of polyimide materials, there are lot of scopes to engineer the physical properties like surface energy and surface roughness of the membrane surface in order to obtain the required wettability. There have been many works focused on the application of different variants of polyimide materials for developing membrane for oil water separation. In this review, we present an itemized review of various works on polyimide materials based oil/water separation in terms of chemical, physical, structural and surface characteristics of the material.

Robust, Lightweight, Hydrophobic, and Fire-Retarded Polyimide/MXene Aerogels for Effective Oil/Water Separation

Polyimide (PI) aerogels have attracted great attention owing to their low density and excellent thermal stability. However, hydrophobic surface modification is required for PI aerogels to improve their ability in oil/water separation due to their amphiphilic characteristic. Two-dimensional MXenes (transition metal carbides/nitrides) can be utilized as nanofillers to enhance the properties of polymers because of their unique layered structure and versatile interface chemistry. Herein, the robust, lightweight, and hydrophobic PI/MXene three-dimensional architectures were fabricated via freeze-drying of polyamide acid/MXene suspensions and thermal imidization. Polyamide acid was synthesized using N-N-dimethylacetamide and 4,4'-oxydianiline. MXene (Ti₃C₂T_x) dispersion was obtained via the etching of Ti₃AlC₂ and ultrasonic exfoliation. Taking advantage of the strong interaction between PI chains and MXene nanosheets, the interconnected, highly porous, and hydrophobic PI/MXene aerogels with low density were fabricated, resulting in the improved compressive performance, remarkable oil absorption capacity, and efficient separation of oil and water. For the PI/MXene-3 aerogel (weight ratio, 5.2:1) without any surface modification, the water contact angle was 119° with a density of 23 mg/cm³. This aerogel can completely recover to its original height after 50 compression-release cycles, exhibiting superelasticity and exceptional fatigue-resistant ability. It also showed high absorption capacities to various organic liquids ranging from approximately 18 to 58 times of their own weight. This hybrid aerogel can rapidly separate the chloroform, soybean oil, and liquid paraffin from the water-oil system. The thermally stable hybrid aerogel also exhibited excellent fire safety properties and outstanding reusability under an extreme environment.