Grafting antibacterial polymer brushes from titanium surface via polydopamine chemistry and activators regenerated by electron transfer ATRP

A bacteriocin-based coating strategy to prevent vancomycin-resistant Enterococcus faecium biofilm formation on materials of interest for indwelling medical devices

The ever-increasing use of exogenous materials as indwelling medical devices in modern medicine offers to pathogens new ways to gain access to human body and begin, in some cases, life threatening infections. Biofouling of such materials with bacteria or fungi is a major concern during surgeries, since this is often associated with biofilm formation and difficult to treat, recalcitrant infections. Intense research efforts have therefore developed several strategies to shield the medical devices' surface from colonization by pathogenic microorganisms. Here, we used dopamine as a coupling agent to coat four different materials of medical interest (plastic polyetheretherketone (PEEK), stainless steel, titanium and silicone catheter) with the bacteriocins, enterocin EJ97-short and the thiopeptide micrococcin P1. Water contact angle measurements and x-ray photoelectron spectroscopy were used to verify the effective coating of the materials. The effect of bacteriocins coated on these materials on the biofilm formation by a vancomycin resistant Enterococcus faecium (VRE) strain was studied by biofilm-oriented antimicrobial test (BOAT) and electron scanning microscopy. The in vitro biocompatibility of bacteriocin-modified biomaterials was tested on cultured human cells. The results demonstrated that the binding of the bacteriocins to the implant surfaces is achieved, and the two bacteriocins in combination could inhibit biofilm formation by E. faecium on all four materials. The modified implant showed no cytotoxicity to the human cells tested. Therefore, surface modification with the two bacteriocins may offer a novel and effective way to prevent biofilm formation on a wide range of implant materials.

Antibacterial Zirconia Surfaces from Organocatalyzed Atom-Transfer Radical Polymerization

Antibacterial coatings are becoming increasingly attractive for application in the field of biomaterials. In this framework, we developed polymer coating zirconia with antibacterial activity using the "grafting from" methodology. First, 1-(4-vinylbenzyl)-3-butylimidazolium chloride monomer was synthesized. Then, the surface modification of zirconia substrates was performed with this monomer via surface-initiated photo atom transfer radical polymerization for antibacterial activity. X-ray photoelectron spectroscopy, ellipsometry, static contact angle measurements, and an atomic force microscope were used to characterize the films for each step of the surface modification. The results revealed that cationic polymers could be successfully deposited on the zirconia surfaces, and the thickness of the grafted layer steadily increased with polymerization time. Finally, the antibacterial adhesion test was used to evaluate the antibacterial activity of the modified zirconia substrates, and we successfully showed the antibacterial activity against Staphylococcus aureus and Pseudomonas aeruginosa strains.

Spherical Polyelectrolyte Brushes as Flocculants and Retention Aids in Wet-End Papermaking

As the criteria of energy conservation, emission reduction, and environmental protection become more important, and with the development of wet-end papermaking, developing excellent retention aids is of great significance. Spherical polyelectrolyte brushes (SPBs) bearing polyelectrolyte chains grafted densely to the surface of core particle have the potential to be novel retention aids in wet-end papermaking not only because of their spherical structure, but also due to controllable grafting density and molecular weight. Such characteristics are crucial in order to design multi-functional retention aids in sophisticated papermaking systems. This review presents some important recent advances with respect to retention aids, including single-component system and dual-component systems. Then, basic theory in papermaking is also briefly reviewed. Based on these advances, it emphatically describes spherical polyelectrolyte brushes, focused on their preparation methods, characterization, conformation, and applications in papermaking. This work is expected to contribute to improve a comprehensive understanding on the composition, properties, and function mechanisms of retention aids, which helps in the further investigation on the design of novel retention aids with excellent performance.

Preparation and Functionalization of Polymers with Antibacterial Properties-Review of the Recent Developments

The presence of antibiotic-resistant bacteria in our environment is a matter of growing concern. Consumption of contaminated drinking water or contaminated fruit or vegetables can provoke ailments and even diseases, mainly in the digestive system. In this work, we present the latest data on the ability to remove bacteria from potable water and wastewater. The article discusses the mechanisms of the antibacterial activity of polymers, consisting of the electrostatic interaction between bacterial cells and the surface of natural and synthetic polymers functionalized with metal cations (polydopamine modified with silver nanoparticles, starch modified with quaternary ammonium or halogenated benzene). The synergistic effect of polymers (N-alkylaminated chitosan, silver doped polyoxometalate, modified poly(aspartic acid)) with antibiotics has also been described, allowing for precise targeting of drugs to infected cells as a preventive measure against the excessive spread of antibiotics, leading to drug resistance among bacteria. Cationic polymers, polymers obtained from essential oils (EOs), or natural polymers modified with organic acids are promising materials in the removal of harmful bacteria. Antimicrobial polymers are successfully used as biocides due to their acceptable toxicity, low production costs, chemical stability, and high adsorption capacity thanks to multi-point attachment to microorganisms. New achievements in the field of polymer surface modification in order to impart antimicrobial properties were summarized.

Biofunctionalization of Porous Titanium Oxide through Amino Acid Coupling for Biomaterial Design

Porous transition metal oxides are widely studied as biocompatible materials for the development of prosthetic implants. Resurfacing the oxide to improve the antibacterial properties of the material is still an open issue, as infections remain a major cause of implant failure. We investigated the functionalization of porous titanium oxide obtained by anodic oxidation with amino acids (Leucine) as a first step to couple antimicrobial peptides to the oxide surface. We adopted a two-step molecular deposition process as follows: self-assembly of aminophosphonates to titanium oxide followed by covalent coupling of Fmoc-Leucine to aminophosphonates. Molecular deposition was investigated step-by-step by Atomic Force Microscopy (AFM) and X-ray Photoemission Spectroscopy (XPS). Since the inherent high roughness of porous titanium hampers the analysis of molecular orientation on the surface, we resorted to parallel experiments on flat titanium oxide thin films. AFM nanoshaving experiments on aminophosphonates deposited on flat TiO₂ indicate the formation of an aminophosphonate monolayer while angle-resolved XPS analysis gives evidence of the formation of an oriented monolayer exposing the amine groups. The availability of the amine groups at the outer interface of the monolayer was confirmed on both flat and porous substrates by the following successful coupling with Fmoc-Leucine, as indicated by high-resolution XPS analysis.

In-Situ Surface Modification of ITO Substrate via Bio-Inspired Mussel Chemistry for Organic Memory Devices

The development of organic memory devices, regarding factors such as structure construction, principle exploration, and material design, has become a powerful supplement to traditional silicon-based information storage. The in-situ growth of materials on substrate surfaces can achieve closer bonding between materials and electrodes. Bio-inspired by mussel chemistry, polydopamine (PDA) was self-assembled on a flexible substrate as a connecting layer, and 2-bromoiso-butyryl bromide (BiBB) was utilized as an initiator for the polymerization of an iridium complex via surface-initiated atom-transfer radical polymerization (SI-ATRP). A device with the structure of Al/PDA-PPy₃Ir/ITO was constructed after the deposition of aluminum. The device exhibited a nonvolatile rewritable memory characteristic with a turn-on voltage of -1.0 V and an ON/OFF current ratio of 6.3 × 10³. In addition, the memory performance of the Al/PDA-PPy₃Ir/ITO device remained stable at bending states due to the intrinsic flexibility of the active layer, which can be expanded into the establishment of flexible memory devices. Spectroscopy and electrochemical characterization suggested that the resistive memory properties of the device stemmed from charge transfer between PDA and iridium polymer in the active layer (PDA-PPy₃Ir) under an applied voltage.

Synthesis and Properties of Hydrogels on Medical Titanium Alloy Surface by Modified Dopamine Adhesion

Medical titanium alloy Ti-6Al-4V (TC4) is an ideal surgical implant material for human tissue repair and replacement. TC4 implantation will be in close contact with human soft tissue and has mechanical compatibility problems. In order to solve this problem, the hydrogel was formed on the surface of TC4 by utilizing the adhesion of dopamine, and the storage modulus of the formed hydrogel matched that of human soft tissue. In this paper, the surface of TC4 was first modified with dopamine (DA) and 2-bromoisobutyryl bromide (BIBB). 2-(2-methoxyethoxy) ethyl methacrylate (MEO₂MA), oligo (ethylene oxide) methacrylate (OEGMA) and 2-methacryloyloxyethyl phosphorylcholine (MPC) are used as monomers, and methylenebisacrylamide (MBA) is used as cross-linking agent. Thermosensitive hydrogels were formed on the surface of modified TC4 by the ATRP technique. The successful synthesis of initiator and hydrogels on TC4 was demonstrated by Fourier transform infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS). The morphology of the hydrogel was observed by the scanning electron microscope (SEM), and the water absorption and temperature sensitivity were investigated by the swelling property. The thermal and mechanical properties of these gels were measured using thermal analysis system (TAS) and dynamic mechanical analyzer (DMA). The results show that the hydrogel on TC4 has good thermal stability and storage modulus that matches human soft tissue.

Synthetic strategies to enhance the long-term stability of polymer brush coatings

High-density, end-anchored macromolecules that form so-called polymer brushes are popular components of bio-inspired surface coatings. In a bio-memetic approach, they have been utilized to reduce friction, repel contamination and control...

Fabrication and Characterization of Graphene Oxide-Coated Plate for Efficient Culture of Stem Cells

BACKGROUND

For stem cell applications in regenerative medicine, it is very important to produce high-quality stem cells in large quantities in a short time period. Recently, many studies have shown big potential of graphene oxide as a biocompatible substance to enhance cell growth. We investigated if graphene oxide-coated culture plate can promote production efficiency of stem cells.

METHODS

Three types of graphene oxide were used for this study. They are highly concentrated graphene oxide solution, single-layer graphene oxide solution, and ultra-highly concentrated single-layer graphene oxide solution with different single-layer ratios, and coated on cell culture plates using a spray coating method. Physiochemical and biological properties of graphene oxide-coated surface were analyzed by atomic force microscope (AFM), scanning electron microscope (SEM), cell counting kit, a live/dead assay kit, and confocal imaging.

RESULTS

Graphene oxide was evenly coated on cell culture plates with a roughness of 6.4 ~ 38.2 nm, as measured by SEM and AFM. Young's Modulus value was up to 115.1 GPa, confirming that graphene oxide was strongly glued to the surface. The ex vivo stem cell expansion efficiency was enhanced as bone marrow-derived stem cell doubling time on the graphene oxide decreased compared to the control (no graphene oxide coating), from 64 to 58 h, and the growth rate increased up to 145%. We also observed faster attachment and higher affinity of stem cells to the graphene oxide compared to control by confocal microscope.

CONCLUSION

This study demonstrated that graphene oxide dramatically enhanced the ex vivo expansion efficiency of stem cells. Spray coating enabled an ultra-thin coating of graphene oxide on cell culture plates. The results supported that utilization of graphene oxide on culture plates can be a promising mean for mass production of stem cells for commercial applications.

Zwitterionic PMCP-functionalized titanium surface resists protein adsorption, promotes cell adhesion, and enhances osteogenic activity

Titanium (Ti) has excellent biocompatibility and corrosion resistance and is widely used as a biomedical material for orthopedic implants. However, the bare Ti surface limits cell adhesion without biological activity and promotes unnecessary protein adsorption, which can activate the coagulation pathway with blood-contacting devices. To improve the antifouling and biological activity of Ti, zwitterionic poly[2-(methacryloyloxy)ethyl choline phosphate] (PMCP) was used to modify the Ti surface via surface-initiated atom transfer radical polymerization. The Ti-PMCP surface reduced bovine serum albumin and fibrinogen adsorption owing to the zwitterionic antifouling property. Ti-PMCP is involved in the unique interaction between PMCP on the Ti surface and phosphate choline on cell membranes, and therefore, the Ti-PMCP surface can promote the adhesion and proliferation of MC3T3-e1 cells and bone marrow mesenchymal cells (BMSCs). In addition, the Ti-PMCP surface was effective in promoting the osteogenic differentiation of MC3T3-e1 cells and BMSCs because the phosphate group in MCP can stimulate osteogenic signaling pathways. Therefore, the PMCP-modified Ti surface can resist protein adsorption and promote the adhesion, proliferation, and differentiation of osteoblast-related cells and has great potential in bone tissue engineering.

A Novel Strategy to Coat Dopamine-Functionalized Titanium Surfaces With Agarose-Based Hydrogels for the Controlled Release of Gentamicin

Introduction

The use of spinal implants for the treatment of back disorders is largely affected by the insurgence of infections at the implantation site. Antibacterial coatings have been proposed as a viable solution to limit such infections. However, despite being effective at short-term, conventional coatings lack the ability to prevent infections at medium and long-term. Hydrogel-based drug delivery systems may represent a solution controlling the release of the loaded antibacterial agents while improving cell integration. Agarose, in particular, is a biocompatible natural polysaccharide known to improve cell growth and already used in drug delivery system formulations. In this study, an agarose hydrogel-based coating has been developed for the controlled release of gentamicin (GS).

Methods

Sand blasted Ti6Al4V discs were grafted with dopamine (DOPA) solution. After, GS loaded agarose hydrogels have been produced and additioned with tannic acid (TA) and calcium chloride (CaCl₂) as crosslinkers. The different GS-loaded hydrogel formulations were deposited on Ti6Al4V-DOPA surfaces, and allowed to react under UV irradiation. Surface topography, wettability and composition have been analyzed with profilometry, static contact angle measurement, XPS and FTIR spectroscopy analyses. GS release was performed under pseudo-physiological conditions up to 28 days and the released GS was quantified using a specific ELISA test. The cytotoxicity of the produced coatings against human cells have been tested, along with their antibacterial activity against S. aureus bacteria.

Results

A homogeneous coating was obtained with all the hydrogel formulations. Moreover, the coatings presented a hydrophilic behavior and micro-scale surface roughness. The addition of TA in the hydrogel formulations showed an increase in the release time compared to the normal GS-agarose hydrogels. Moreover, the GS released from these gels was able to significantly inhibit S. aureus growth compared to the GS-agarose hydrogels. The addition of CaCl₂ to the gel formulation was able to significantly decrease cytotoxicity of the TA-modified hydrogels.

Conclusions

Due to their surface properties, low cytotoxicity and high antibacterial effects, the hereby proposed gentamicin-loaded agarose-hydrogels provide new insight, and represent a promising approach for the surface modification of spinal implants, greatly impacting their application in the orthopedic surgical scenario.

Biomorphic Ceramics: Synthesis and Characterization of Preceramic Polymer-Modified Melanin

Recent efforts have demonstrated that the morphology of ceramics can be manipulated to control both their deformation mechanism and mechanical performance. However, precise control of the ceramic nanostructure is still difficult to achieve. Biotemplating, leading to biomorphic materials, provides a facile route to manipulate the nanostructure of the resulting materials, and the use of melanin as a coating provides a new route to biotemplated materials. Melanin is underutilized for structural materials partly due to the cost of procuring it from natural sources and the inability to control the shape and sizes of melanin particles. Taking a combined synthetic biology and chemical synthesis approach, we report the melanization of Escherichia coli and its subsequent silanization and functionalization with preceramic polymers to make novel biomorphic silicon-based ceramic materials. Graft-to and graft-from reactions were used to append preceramic polymers to the melanin, followed by pyrolysis under argon. Samples were analyzed by FTIR, XRD, XPS, and TEM and found to retain the shape and size of the original cells with high fidelity. The homogeneity of coverage and yield of the resulting ceramic materials depended on the type of grafting reaction. This work provides a promising proof-of-concept that bacterial-templated ceramics can be readily made and opens a host of possibilities for further studies and applications.

Understanding and optimizing the antibacterial functions of anodized nano-engineered titanium implants

Nanoscale surface modification of titanium-based orthopaedic and dental implants is routinely applied to augment bioactivity, however, as is the case with other cells, bacterial adhesion is increased on nano-rough surfaces. Electrochemically anodized Ti implants with titania nanotubes (TNTs) have been proposed as an ideal implant surface with desirable bioactivity and local drug release functions to target various conditions. However, a comprehensive state of the art overview of why and how such TNTs-Ti implants acquire antibacterial functions, and an in-depth knowledge of how topography, chemistry and local elution of potent antibiotic agents influence such functions has not been reported. This review discusses and details the application of nano-engineered Ti implants modified with TNTs for maximum local antibacterial functions, deciphering the interdependence of various characteristics and the fine-tuning of different parameters to minimize cytotoxicity. An ideal implant surface should cater simultaneously to ossoeintegration (and soft-tissue integration for dental implants), immunomodulation and antibacterial functions. We also evaluate the effectiveness and challenges associated with such synergistic functions from modified TNTs-implants. Particular focus is placed on the metallic and semi-metallic modification of TNTs towards enabling bactericidal properties, which is often dose dependent. Additionally, there are concerns over the cytotoxicity of these therapies. In that light, research challenges in this domain and expectations from the next generation of customizable antibacterial TNTs implants towards clinical translation are critically evaluated. STATEMENT OF SIGNIFICANCE: One of the major causes of titanium orthopaedic/dental implant failure is bacterial colonization and infection, which results in complete implant failure and the need for revision surgery and re-implantation. Using advanced nanotechnology, controlled nanotopographies have been fabricated on Ti implants, for instance anodized nanotubes, which can accommodate and locally elute potent antibiotic agents. In this pioneering review, we shine light on the topographical, chemical and therapeutic aspects of antibacterial nanotubes towards achieving desirable tailored antibacterial efficacy without cytotoxicity concerns. This interdisciplinary review will appeal to researchers from the wider scientific community interested in biomaterials science, structure and function, and will provide an improved understanding of controlling bacterial infection around nano-engineered implants, aimed at bridging the gap between research and clinics.

Dual signal amplification based on polysaccharide-initiated ring-opening polymerization and click polymerization for exosomes detection

Exosomes, as a biomarker with enhancing tumor invasion and spread, play an essential role for lung cancer diagnosis, therapy, and prognosis. In this work, a novel electrochemical sensor was fabricated for detecting exosomes secreted by lung cancer cells based on polysaccharide-initiated ring-opening polymerization (ROP) and click polymerization. First, MPA formed a self-assembled monolayer on the gold electrode surface, and then anti-EGFR was immobilized on the electrode surface by amide bond. Subsequently, a lot of phosphate groups were introduced by the specific recognition between anti-EGFR and exosomes, then sodium alginate grafted Glycidyl propargyl ether (SA-g-GPE) prepared via ROP was attached to the exosomes through PO₄^3-Zr⁴⁺-COOH coordination bond. After that, click polymerization was initiated by alkyne groups on the SA-g-GPE polymerization chain to realize highly sensitive detection of A549 exosomes. Under the optimum conditions, the fabricated sensor showed a good linear relationship between the logarithm of exosomes concentration and peak current in the range of 5 × 10³ - 5 × 10⁹ particles/mL, and the limit of detection (LOD) was as low as 1.49 × 10² particles/mL. In addition, this method had the advantages of high specificity, anti-interference, high sensitivity, simplicity, rapidity and green economy, which proposed a novel avenue for the detection of exosomes, and also had potential applications in early cancer diagnosis and biomedicine.

Surface Functionalization of Graphene Oxide with Polymer Brushes for Improving Thermal Properties of the Polymer Matrix

In this work, polymethyl methacrylate (PMMA) and polystyrene (PS) with controlled structures would be grafted on graphene material. The hybrid materials were prepared by coating graphene oxide (GO) with polydopamine (PDA) as a reactive underlayer and reducing agent, subsequently, surface-initiated polymerization of monomers (methyl methacrylate, styrene) based on the activators regenerated electron transfer atom transfer radical polymerization (ARGET-ATRP) technique. The polymer brush-modified graphene materials were then incorporated into the PMMA or PS matrix to get polymer nanocomposites with better thermal properties. The results of Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and thermal gravimetric analysis (TGA) demonstrated that PMMA and PS chains were successfully anchored on the surfaces of functionalized GO sheets. The influence of the grafted polymer brush-modified GO on thermal stability of PMMA and PS was investigated by a simultaneous thermal analyzer. Thermal conductivity of the polymer nanocomposite was determined by a conductive calorimeter. The results showed that thermal stability, glass transition temperature ( $T_{\text{g}}$ ), and thermal conductivity of the polymer nanocomposites were obviously improved compared with pure PMMA or PS.

Synthesis of rifaximin loaded chitosan-alginate core-shell nanoparticles (Rif@CS/Alg-NPs) for antibacterial applications

The present work aims to synthesize the rifaximin loaded chitosan-alginate core-shell nanoparticles (Rif@CS/Alg-NPs) for antibacterial applications. The core-shell nanoparticles (Rif@CS/Alg-NPs) were characterized by Fourier Transform Infrared (FT-IR) spectroscopy, Scanning Electron Microscopy (SEM), Transmission Electron Microscopy (TEM), X-rays diffraction (XRD) and zeta analyzer. The antibacterial activities of Rif@CS/Alg-NPs were investigated against three species of bacteria namely Escherichia coli (E. coli), Pseudomonas aeruginosa (PA) and Bacillus haynesii (BH). Rif@CS/Alg-NPs exhibited outstanding antibacterial activities against E. coli, P. aeroginosa and Bacillus haynesii (BH) with 24 mm, 30 mm and 34 mm zone of inhibitions, respectively. Cytotoxicity of Rif@CS/Alg-NPs was also evaluated against human lung adenocarcinoma cell line A549 and found to be nontoxic. The drug release behavior of Rif@CS/Alg-NPs was investigated at different pH levels and maximum drug release (80%) was achieved at pH (7.2). The drug release kinetic data followed the Higuchi (R² = 0.9963) kinetic model, indicating the drug release from Rif@CS/Alg-NPs as a square root of time-dependent process and diffusion controlled. Current research provides a cost-effective and green approach toward the synthesis of Rif@CS/Alg-NPs for its antibacterial applications.

Polymer Brushes via Surface-Initiated Electrochemically Mediated ATRP: Role of a Sacrificial Initiator in Polymerization of Acrylates on Silicon Substrates

Silicon wafers as semiconductors are essential components of integrated circuits in electronic devices. For this reason, modification of the silicon surface is an important factor in the manufacturing of new hybrid materials applied in micro- and nanoelectronics. Herein, copolymer brushes of hydrophilic poly(2-hydroxyethyl acrylate) (PHEA) and hydrophobic poly(tert-butyl acrylate) (PtBA) were grafted from silicon wafers via simplified electrochemically mediated atom transfer radical polymerization (seATRP) according to a surface-initiated approach. The syntheses of PHEA-b-PtBA copolymers were carried out with diminished catalytic complex concentration (successively 25 and 6 ppm of Cu). In order to optimize the reaction condition, the effect of the addition of a supporting electrolyte was investigated. A controlled increase in PHEA brush thickness was confirmed by atomic force microscopy (AFM). Various other parameters including contact angles and free surface energy (FSE) for the modified silicon wafer were presented. Furthermore, the effect of the presence of a sacrificial initiator in solution on the thickness of the grafted brushes was reported. Successfully fabricated inorganic–organic hybrid nanomaterials show potential application in biomedicine and microelectronics devices, e.g., biosensors.

Substrate-independent Cu(0)-mediated controlled radical polymerization: grafting of block copolymer brushes from poly(dopamine) modified surfaces

A method is presented combining poly(dopamine) chemistry and surface-initiated Cu(0)-mediated controlled radical polymerization (SI-CuCRP). Polymer brushes and block copolymer brushes are grafted independent of the original surface properties.

Accessible and sustainable Cu(0)-mediated radical polymerisation for the functionalisation of surfaces

Towards use of environmentally benign solvents and ambient conditions for surface functionalisation by controlled growth of thick cationic polymer brushes.

Surface-Induced ARGET ATRP for Silicon Nanoparticles with Fluorescent Polymer Brushes

Well-defined polymer brushes attached to nanoparticles offer an elegant opportunity for surface modification because of their excellent mechanical stability, functional versatility, high graft density as well as controllability of surface properties. This study aimed to prepare hybrid materials with good dispersion in different solvents, and to endow this material with certain fluorescence characteristics. Well-defined diblock copolymers poly (styrene)-b-poly (hydroxyethyl methyl acrylate)-co-poly (hydroxyethyl methyl acrylate- rhodamine B) grafted silica nanoparticles (SNPs-g-PS-b-PHEMA-co-PHEMA-RhB) hybrid materials were synthesized via surface-initiated activators regenerated by electron transfer atom transfer radical polymerization (SI-ARGET ATRP). The SNPs surfaces were modified by 3-aminopropyltriethoxysilane (KH-550) firstly, then the initiators 2-Bromoisobutyryl bromide (BIBB) was attached to SNPs surfaces through the esterification of acyl bromide groups and amidogen groups. The synthetic initiators (SNPs-Br) were further used for the SI-ARGET ATRP of styrene (St), hydroxyethyl methyl acrylate (HEMA) and hydroxyethyl methyl acrylate-rhodamine B (HEMA-RhB). The results indicated that the SI-ARGET ATRP initiator had been immobilized onto SNPs surfaces, the Br atom have located at the end of the main polymer chains, and the polymerization process possessed the characteristic of controlled/"living" polymerization. The SNPs-g-PS-b-PHEMA-co-PHEMA-RhB hybrid materials show good fluorescence performance and good dispersion in water and EtOH but aggregated in THF. This study demonstrates that the SI-ARGET ATRP provided a unique way to tune the polymer brushes structure on silica nanoparticles surface and further broaden the application of SI-ARGET ATRP.