Preparation of water-soluble cellulose derivatives using TEMPO radical-mediated oxidation at extended reaction time

Effect of modified cellulose-based emulsion on gel properties and protein conformation of Nemipterus virgatus surimi

Microcrystalline cellulose was modified by TEMPO oxidation combined with ultrasound to prepare modified cellulose-based emulsion. The effect of different emulsion concentration on gel properties and protein conformation of surimi was investigated. The results showed the length and width of microcrystalline cellulose were reduced, and a large amount of -COOH was introduced into modified cellulose. Direct addition of flaxseed oil decreased the gel strength and WHC from 3640.49 g·mm and 76.94% to 2702.95 g·mm and 75.89%, respectively, while 5% modified cellulose-based emulsion could improve the gel properties of surimi. Surimi gel containing 5% emulsion had the highest hydrophobic interaction, disulfide bond and β-sheet content. Moreover, protein network structure was the densest in 5% emulsion group. Therefore, modified cellulose-based emulsion could be used to compensating for the negative impact of direct addition of flaxseed oil on surimi, which provided a new idea for the development of healthy and new emulsified surimi products.

In situ biomineralization reinforcing anisotropic nanocellulose scaffolds for guiding the differentiation of bone marrow-derived mesenchymal stem cells

Nanocellulose (NC) is a promising biopolymer for various biomedical applications owing to its biocompatibility and low toxicity. However, it faces challenges in tissue engineering (TE) applications due to the inconsistency of the microenvironment within the NC-based scaffolds with target tissues, including anisotropy microstructure and biomechanics. To address this challenge, a facile swelling-induced nanofiber alignment and a novel in situ biomineralization reinforcement strategies were developed for the preparation of NC-based scaffolds with tunable anisotropic structure and mechanical strength for guiding the differentiation of bone marrow-derived mesenchymal stem cells for potential TE application. The bacterial cellulose (BC) and cellulose nanofibrils (CNFs) based scaffolds with tunable swelling anisotropic index in the range of 10-100 could be prepared by controlling the swelling medium. The in situ biomineralization efficiently reinforced the scaffolds with 2-4 times and 10-20 times modulus increasement for BC and CNFs, respectively. The scaffolds with higher mechanical strength were superior in supporting cell growth and proliferation, suggesting the potential application in TE application. This work demonstrated the feasibility of the proposed strategy in the preparation of scaffolds with mechanical anisotropy to induce cells-directed differentiation for TE applications.

Scalable phosphorylated cellulose production with improved environmental sustainability, crosslinkability and processability using 3D bioprinting for dye remediation

In the present work, phosphorylated cellulose (PC) gel has been produced following an environmentally benign approach using agro-based chemicals with improved yield. The PC gels produced were transparent, negatively charged with high consistency, charge content (1133.33 mmol/kg), degree of substitution (DS) of 0.183 and increased yield (>87 %). The XPS and EDS analysis confirms the covalently bonded phosphate groups at weight percent of 9.42 % and 11.01 %, respectively. The life cycle assessment (LCA) shows that PC gel production via the phosphorylation route is an ecologically favourable strategy compared with traditional TEMPO oxidation, resulting in 1.67 times lower CO2 emission. The rheological studies of PC gels show shear-thinning behaviour with improved 3D printability followed by heat-induced crosslinking of phosphate groups. The mechanistic insights for the condensation of phosphate to form a phosphoric ester group during cross-linking were evaluated through 31P solid-state NMR and XPS studies. Interestingly, the 3D-printed structures showed high structural stability under both compression and tensile load in both dry and wet conditions, with high water absorption (5408.33 %) and swelling capacity of 700 %. The structures show improved methylene blue (MB) remediation capabilities with a maximum removal efficiency of 99 % for 10-200 mg/L and more than seven times reusability. This work provides a green, facile and energy-efficient strategy for fabricating PCs with easy processability through additive manufacturing techniques for producing value-added products, opening up new avenues for high-performance applications.

Functionalization Methods of Starch and Its Derivatives: From Old Limitations to New Possibilities

It has long been known that starch as a raw material is of strategic importance for meeting primarily the nutritional needs of people around the world. Year by year, the demand not only for traditional but also for functional food based on starch and its derivatives is growing. Problems with the availability of petrochemical raw materials, as well as environmental problems with the recycling of post-production waste, make non-food industries also increasingly interested in this biopolymer. Its supporters will point out countless advantages such as wide availability, renewability, and biodegradability. Opponents, in turn, will argue that they will not balance the problems with its processing and storage and poor functional properties. Hence, the race to find new methods to improve starch properties towards multifunctionality is still ongoing. For these reasons, in the presented review, referring to the structure and physicochemical properties of starch, attempts were made to highlight not only the current limitations in its processing but also new possibilities. Attention was paid to progress in the non-selective and selective functionalization of starch to obtain materials with the greatest application potential in the food (resistant starch, dextrins, and maltodextrins) and/or in the non-food industries (hydrophobic and oxidized starch).

Facile preparation, optical mechanism elaboration, and bio-imaging application of fluorescent cellulose nanocrystals with tunable emission wavelength

Interfacing cellulose nanocrystals (CNCs) with fluorescent materials provides more possibilities for constructing of sensory/imaging platforms in biomedical applications. In this work, by harnessing the efficient extraction accompanied modification of CNCs and adjustable optical properties of carbon dots (CDs), we report the constructions and emission wavelength tuning of fluorescent CNCs (F-CNCs) composed of CNC nano-scaffolds and CDs. The as-prepared CNCs are densely decorated with citric acid (CA), which plays the role of carbon source for the in-situ synthesis of CDs on CNCs. For the F-CNCs carrying blue, green, and red emissive CDs, ethylenediamine (EDA), urea, and thiourea are the N or N/S sources. Fingerprints of chemical groups, morphological characters, and redox activities are resolved to elaborate the optical mechanisms of CDs with varying emission colors. The emission wavelength is adjusted by either changing the particle size or introducing new emission centers. Both are primarily achieved via precursor engineering. The F-CNCs reveal quantum yields (QYs) >22 % and negligible fluorescence quenching (< 6 %) upon continuous excitation as long as 24 h. Benefited from their cell membrane penetration capability, the F-CNCs with different emission wavelengths were challenged for multiplexed cytoplasm imaging.

Characterization and comparison of carboxymethylation and TEMPO-mediated oxidation for polysaccharides modification

In this study, carboxymethylation and TEMPO-mediated oxidation were compared for their ability to introduce carboxyl groups to polysaccharides, using cellulose and chitin as model polysaccharides. The carboxyl group contents and changes in the molecular weight of carboxymethylated and TEMPO-oxidized cellulose/chitin were measured. The results revealed that carboxymethylation achieved higher carboxyl group contents, with values of 4.99 mmol/g for cellulose and 4.46 mmol/g for chitin, whereas for TEMPO-oxidized cellulose and chitin, the values were 1.64 mmol/g and 1.12 mmol/g, respectively. As a consequence of TEMPO-mediated oxidation, polysaccharides underwent degradation, leading to a decrease in the molecular weight of 42.46 % for oxidized cellulose and 64.5 % for oxidized chitin. Additionally, the crystallinity of carboxymethylated polysaccharides decreased with an increase in the carboxyl group contents, whereas that of TEMPO-oxidized polysaccharides remained unchanged. Furthermore, TEMPO-mediated oxidation selectively oxidized C6 primary hydroxyls, while carboxylmethylation converted all the hydroxyl groups on the polysaccharides.

Chemistry of Hydroxypropyl Cellulose Oxidized by Two Selective Oxidants

Along with the increased usage of cellulose in the manufacture of novel materials, those of its derivatives that have good solubility in water or organic solvents have become increasingly important. In this study, hydroxypropyl cellulose (HPC), a cellulosic derivative with distinct features, was utilized to investigate how two of the most-selective oxidation methods currently available in the literature act on the constituent OH groups of both the side chain and the anhydroglycosidic unit in HPC. The oxidation reactions were carried out first using TEMPO, sodium hypochlorite, and sodium bromide, then sodium periodate (NaIO4), for 5 h. A combination of these two protocols was applied. The amount of aldehyde and number of carboxylic groups introduced after oxidation was determined, while the changes in the morphological features of oxidized HPC were, additionally, assessed. Furthermore, utilizing Fourier-transform infrared spectra, X-ray diffraction, and thermogravimetric studies, the chemical structure, crystallinity, and thermal stability of the oxidized HPC samples were examined and compared.

Antibacterial and Antifungal Silver Nanoparticles with Tunable Size Embedded in Various Cellulose-Based Matrices

The aim of this study was to synthesize silver nanoparticles (AgNPs) using cellulose derivatives and to evaluate their antimicrobial potential. As effective reducing and stabilizing agents for AgNPs, cellulose derivatives, such as hydroxypropyl cellulose (HPC), methylcellulose (MC), ethylcellulose (EC), and cellulose acetate (CA), were used. Their ability to reduce silver ions as well as the size of the resulting AgNPs were compared. The formation and stability of the reduced AgNPs in the solution were monitored using UV-Vis analysis. The size, morphology, and charge of the AgNPs were evaluated. We found that, when using cellulosic derivatives, AgNPs with sizes ranging from 17 to 89 nm and different stabilities were obtained. The parameters, such as size and ζ potential indicate the stability of AgNPs, with AgNPs-CA and AgNPs-HPC being considered more stable than AgNPs-EC and AgNPs-MC since they show higher ζ potential values. In addition, the AgNPs showed antimicrobial activity against all reference strains and clinical isolates. MIC values between 0.0312 and 0.125 mM had a bactericidal effect on both Gram-positive and Gram-negative bacteria. The fungicidal effect was obtained at a MIC value of 0.125 mM. These results may provide rational support in the design of medical gauze products, including gauze pads, rolls, and sponges.

Emerging Food Packaging Applications of Cellulose Nanocomposites: A Review

Cellulose is the most abundant biopolymer on Earth, which is synthesized by plants, bacteria, and animals, with source-dependent properties. Cellulose containing β-1,4-linked D-glucoses further assembles into hierarchical structures in microfibrils, which can be processed to nanocellulose with length or width in the nanoscale after a variety of pretreatments including enzymatic hydrolysis, TEMPO-oxidation, and carboxymethylation. Nanocellulose can be mainly categorized into cellulose nanocrystal (CNC) produced by acid hydrolysis, cellulose nanofibrils (CNF) prepared by refining, homogenization, microfluidization, sonification, ball milling, and the aqueous counter collision (ACC) method, and bacterial cellulose (BC) biosynthesized by the Acetobacter species. Due to nontoxicity, good biodegradability and biocompatibility, high aspect ratio, low thermal expansion coefficient, excellent mechanical strength, and unique optical properties, nanocellulose is utilized to develop various cellulose nanocomposites through solution casting, Layer-by-Layer (LBL) assembly, extrusion, coating, gel-forming, spray drying, electrostatic spinning, adsorption, nanoemulsion, and other techniques, and has been widely used as food packaging material with excellent barrier and mechanical properties, antibacterial activity, and stimuli-responsive performance to improve the food quality and shelf life. Under the driving force of the increasing green food packaging market, nanocellulose production has gradually developed from lab-scale to pilot- or even industrial-scale, mainly in Europe, Africa, and Asia, though developing cost-effective preparation techniques and precisely tuning the physicochemical properties are key to the commercialization. We expect this review to summarise the recent literature in the nanocellulose-based food packaging field and provide the readers with the state-of-the-art of this research area.

Development of hydrogel based on Carboxymethyl cellulose/poly(4-vinylpyridine) for controlled releasing of fertilizers

A novel Carboxymethyl cellulose (CMC) and poly (4-vinylpyridine) (P4VP) hydrogel system is synthesized with different ratios, in the presence of cross-linker N, N,- methylene bis-acrylamide (MBA). The hydrogel is characterized via FTIR spectroscopy, thermal gravimetric analysis (TGA), X-ray diffraction (XRD), and scanning electron microscope (SEM). The FTIR results showed a strong interaction between both CMC, P4VP and the loaded fertilizer. The water uptake of the hydrogel was evaluated by swelling tests under variations in pH, biodegradability was investigated in soil to simulate real-world conditions. To determine the best release behavior of urea and calcium nitrate from the hydrogel, fertilizers were loaded with different ratios onto the hydrogel during its formation. Fertilizers release was followed by Atomic absorption spectroscopy to study the release of calcium nitrate and urea. Release kinetic parameters were obtained based on different mathematical models as Zero order, First order, Korsmeyer–Peppas and Higuchi models. The suitable proportionality between the mathematical models used and the fertilizers release was determined based on the correlation coefficients (R²). According to Zero order model urea release showed independent concentration. Based on Korsmeyer-Pappas and Higuchi models with high n value and R² equals to 0.97. Compared to urea, Ca²⁺, Zero order and Higuchi have been ignored due to their poor correlation coefficients values as proportion with Ca²⁺ fertilizer release.

Insights on Cellulose Research in the Last Two Decades in Romania

In the current global context, cellulose fulfills those characteristics that give it clear advantages over synthetic fibers, having a huge potential for substituting fossil-based materials which are polluting and harmful to ecosystems. Research conducted in most laboratories around the world in the field of cellulose is overwhelmingly aimed at industrial needs because features such as renewability and low cost are the most important attributes for economic success. In this global effort, Romanian researchers contribute through achievements that are briefly reviewed in this paper. These refer to the main achievements reported after 2000 in the field of cellulose characterization and cellulose functionalization, as well as the main areas where cellulose-based materials were applied.