FTIR spectral signatures of amazon inorganic phosphates: Igneous, weathering, and biogenetic origin

Effect of Crystalline Phase and Facet Nature on the Adsorption of Phosphate Species onto TiO2 Nanoparticles

The current use of TiO2 nanoparticles raises questions about their impact on our health. Cells interact with these nanoparticles via the phospholipid membrane and, in particular, the phosphate head. This highlights the significance of understanding the interaction between phosphates and nanoparticles possessing distinct crystalline structures, specifically anatase and rutile. It is crucial to determine whether this adsorption varies based on the exposed facet(s). Consequently, various nanoparticles of anatase and rutile TiO2, characterized by well-defined morphologies, were synthesized. In the case of the anatase samples, bipyramids, needles, and cubes were obtained. For the rutile samples, all exhibited a needle-like shape, featuring {110} facets along the long direction of the needles and facets {111} on the upper and lower parts. Phosphate adsorption experiments carried out at pH 2 revealed that the maximum adsorption was relatively consistent across all samples, averaging around 1.5 phosphate·nm-2 in all cases. Experiments using infrared spectroscopy on dried TiO2 powders showed that phosphates were chemisorbed on the surfaces and that the mode of adsorption depended on the crystalline phase and the nature of the facet: the anatase phase favors bidentate adsorption more than the rutile crystalline phase.

Adsorption performance and mechanism of a starch-stabilized ferromanganese binary oxide for the removal of phosphate

Effective removal of phosphate from water is essential for preventing the eutrophication and worsening of water quality. This study aims to enhance phosphate removal by synthesizing starch-stabilized ferromanganese binary oxide (FMBO-S), discover the factors, and investigate adsorption mechanisms. FMBO and FMBO-S properties were studied using Scanning Electron Microscopy, BET analysis, Polydispersity Index (PDI), Fourier Transform Infrared Spectroscopy, and X-ray Photoelectron Spectroscopy (XPS). After starch loading, the average pore diameter increased from 14.89 Å to 25.16 Å, and significantly increased the pore volume in the mesopore region. FMBO-S showed a PDI value below 0.5 indicating homogeneous size dispersity and demonstrated faster and higher adsorption capacity: 61.24 mg g-1 > 28.57 mg g-1. Both FMBO and FMBO-S adsorption data fit well with the pseudo-second-order and Freundlich models, indicating a chemisorption and multilayered adsorption process. The phosphate adsorption by FMBO was pH-dependent, suggesting electrostatic attraction as the dominant mechanism. For the FMBO-S, phosphate adsorption was favored in a wide pH range, despite the weaker electrostatic attraction as evident from the point of zero charge and zeta potential values, indicating ligand exchange as a main mechanism. Moreover, the XPS analysis shows a significant change in the proportion of Fe species for FMBO-S than FMBO after phosphate adsorption, indicating significant involvement of Fe. Meanwhile, phosphate adsorption was almost unaffected by the presence of Cl-, NO3-, and SO42- anions, whereas CO32- significantly reduced the adsorption capacity. This study revealed that FMBO-S could be a promising, low-cost adsorbent for phosphate removal and recovery from water.

Improving the Three-Dimensional Printability of Potato Starch Loaded onto Food Ink

This study focuses on improving the 3D printability of pea protein with the help of food inks designed for jet-type 3D printers. Initially, the food ink base was formulated using nanocellulose-alginate with a gradient of native potato starch and its 3D printability was evaluated. The 3D-printed structures using only candidates for the food ink base formulated with or without potato starch exhibited dimensional accuracy exceeding 95% on both the X and Y axes. However, the accuracy of stacking on the Z-axis was significantly affected by the ink composition. Food ink with 1% potato starch closely matched the CAD design, with an accuracy of approximately 99% on the Z-axis. Potato starch enhanced the stacking of 3D-printed structures by improving the electrostatic repulsion, viscoelasticity, and thixotropic behavior of the food ink base. The 3D printability of pea protein was evaluated using the selected food ink base, showing a 46% improvement in dimensional accuracy on the Z-axis compared to the control group printed with a food ink base lacking potato starch. These findings suggest that starch can serve as an additive support for high-resolution 3D jet-type printing of food ink material.

Online monitoring of phytate content in plant residuals during wet-treatment

The occurrence of organically bound phosphorus (P) as phytate in plant-based feeding material is a challenge for livestock farming due to limited utilization during the digestion by the animal. Its excretion into the environment through the manure pathway, poses a challenge, due to increased eutrophication and restrictions for P. Hence, while the routine supplementation of phytase enzymes in monogastric diets is common practice, metabolically triggering endogenous plant enzymes by wet-treatment prior to feeding can also lead to a better utilization of phytate bound P and increased digestibility by the animal. Nonetheless, traditional quantification of residual phytate content in plant material is both labor- and chemical-intense. The aim of this study is, therefore, to predict the remaining phytate content during wet-treatment through a straightforward and flexible methodological approach based on real-time analysis. For this, rye bran is used as a model substrate. A partial least squares regression algorithm relates the infrared spectra to the concentrations and predict the amount of P species that are transferred from the bran matrix to the liquid phase. By applying a mass balance for P and considering the effect of water compression, the amount of residual phytate content in rye bran at different time points of wet-treatment is determined. Results are compared to wet chemical methods, resulting in a RMSEP of 0.28 gphytate∙100 gbran-1. In addition, the study demonstrates the feasibility of this approach and provides insights into phytate degradation in plant residuals. The method holds the potential for further applications for the screening and investigation of feed material conditioning and also offers the possibility to employ various real-time analytical techniques for assessing phytate remnants in biological samples during wet-treatment.

Selective Shielding of the (002) Plane Enabling Vertically Oriented Zinc Plating for Dendrite-Free Zinc Anode

Uncontrolled growth of Zn dendrites hinders the future development of aqueous Zn-ion batteries. Despite that the (100) plane possesses better zincophilic ability and fast kinetics, dendrites are generally suppressed via (002) plane-oriented Zn deposition in previous reports; the ordered (100) plane-dominant Zn deposition, especially under high current density has not yet been realized. Herein, vertically-oriented Zn plating with preferential growth of (100) plane is reported using disodium lauryl phosphate (DLP) as an electrolyte additive. DLP is preferentially anchored on the Zn (002) crystal plane via the polar phosphate group, then the deposition of Zn atoms on the (002) plane is retarded by the long alkyl chain, finally promoting the preferred growth of the (100) plane. This unique growth pattern results in ultrastable Zn plating/stripping at a super-high current density of 50 mA cm-2 , with a cumulative capacity of 8500 mAh cm-2 . The Zn//Zn symmetric cell also cycles steadily for 700 h with a large areal capacity of 10 mAh cm-2 at a current density of 10 mA cm-2 . This study provides new insights into the realization of dendrite-free Zn anodes by crystal plane modulation.

Synergistic effects of hydrogen peroxide and phosphate on uranium(VI) immobilization: implications for the remediation of groundwater at decommissioned in situ leaching uranium mine

The processes of acid in situ leaching (ISL) uranium (U) mines cause the pollution of groundwater. Phosphate (PO43-) has the potential to immobilize U in groundwater through forming highly insoluble phosphate minerals, but the performance is highly restricted by low pH and high sulfate concentration. In this study, hydrogen peroxide (H2O2) and PO43- were synergistically used for immobilizing U based on the specific properties of groundwater from a decommissioned acid ISL U mine. The removal mechanisms of U and the stability of U on the formed minerals were elucidated by employing X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and kinetic experiments. Our results indicated that the removal of U by simultaneously adding H2O2 and PO43- was significantly higher than the removal of U by individually adding H2O2 or PO43-. The removal of U increased with increasing PO43- concentration from 20 to 200 mg L-1 while decreased with increasing H2O2 concentration from 0.003 to 0.3%. Specifically, the removal efficiency of U from groundwater reached 98% after the application of 0.003% H2O2 and 200 mg L-1 PO43-. Amorphous iron phosphate that preferentially formed at low H2O2 and high PO43- concentrations played a dominant role in U removal, while the formations of schwertmannite and crystalline iron phosphates may be also contributed to the removal of U. This was significantly different from the immobilization mechanism of U through the formation of uranyl phosphate minerals after adding phosphate. The kinetic experimental results suggested that the immobilized U had a good stability. Our research may provide a promising method for in situ remediating U-contaminated groundwater at the decommissioned acid ISL U mines.

Cold plasma synthesis of phosphorus-doped CoFe2O4 with oxygen vacancies for enhanced OER activity

Spinel-type metal oxides are promising electrocatalysts for the oxygen evolution reaction (OER) due to their unique electronic structure and low cost. Herein, we induced oxygen vacancies and doped phosphorus into CoFe2O4 using cold plasma. The abundant oxygen vacancies enhanced hydrophilicity and modified the electronic structure of CoFe2O4, while the phosphorus doping formed numerous new active centers. The doped P and formed FeP promoted the charge transfer and improved the conductivity of the catalyst. The phosphorus-doped CoFe2O4 exhibited exceptional OER activity with an overpotential of 180 mV at 10 mA cm-2 and a Tafel slope of 65.8 mV dec-1 in an alkaline electrolyte. DFT calculations confirmed that phosphorus doping can improve the charge distribution near the Fermi level and optimize the d-band center position.

Chemical Studies of Multicomponent Kidney Stones Using the Modern Advanced Research Methods

Defining the kidney stone composition is important for determining a treatment plan, understanding etiology and preventing recurrence of nephrolithiasis, which is considered as a common, civilization disease and a serious worldwide medical problem. The aim of this study was to investigate the morphology and chemical composition of multicomponent kidney stones. The identification methods such as infrared spectroscopy (FTIR), X-ray diffraction (XRD), and electron microscopy with the EDX detector were presented. The studies by the X-ray photoelectron spectroscopy (XPS) were also carried out for better understanding of their chemical structure. The chemical mapping by the FTIR microscopy was performed to show the distribution of individual chemical compounds that constitute the building blocks of kidney stones. The use of modern research methods with a particular emphasis on the spectroscopic methods allowed for a thorough examination of the subject of nephrolithiasis.

Electrochemical and Structural Characterization of Lanthanum-Doped Hydroxyapatite: A Promising Material for Sensing Applications

In the quest to find powerful modifiers of screen-printed electrodes for sensing applications, a set of rare earth-doped Ca_10-xRE_x(PO₄)₆(OH)₂ (RE = La, Nd, Sm, Eu, Dy, and Tm and x = 0.01, 0.02, 0.10, and 0.20) hydroxyapatite (HAp) samples were subjected to an in-depth electrochemical characterization using electrochemical impedance spectroscopy and cyclic and square wave voltammetry. Among all of these, the inorganic phosphates doped with lanthanum proved to be the most reliable, revealing robust analytical performances in terms of sensitivity, repeatability, reproducibility, and reusability, hence paving the way for their exploitation in sensing applications. Structural data on La-doped HAp samples were also provided by using different techniques, including optical microscopy, X-ray diffraction, Rietveld refinement from X-ray data, Fourier transform infrared, and Raman vibrational spectroscopies, to complement the electrochemical characterization.

Advancing phosphate ore minerals separation with sustainable flotation reagents: An investigation into highly selective biobased depressants

Froth flotation has been a commonly employed technique to enrich natural ores by removing impurities based on the surface properties of minerals. This process involves the use of various reagents, including collectors, depressants, frothers, and activators, which are often chemically synthesized and may represent environmental risks. Therefore, there is a growing need to develop biobased reagents that offer more sustainable alternatives. The aim of this review is to provide a comprehensive assessment of the potential of biobased depressants as a sustainable alternative to traditional reagents in selective flotation process for phosphate ore minerals. To achieve this objective, the review investigates the extraction and the purification methods of different biobased depressants, analyzes the specific conditions for reagent interaction with minerals, and assess the biobased depressants' performance through a range of fundamental studies. These studies aim to (i) provide a better understanding of the adsorption behavior of some biobased depressants onto the surfaces of apatite, calcite, dolomite, and quartz comprised in different mineral systems by measuring their zeta potential and analyzing their Fourier transform infrared spectra before and after contact with these reagents, (ii) determine the depressants' adsorption amounts, (iii) evaluate their effect on the contact angle of bare minerals, and (iv) assess their ability to inhibit the flotation of the studied minerals. The outcomes revealed the potential use and the promising applicability of these unconventional reagents since their performance is comparable to that of conventional reagents. In addition to their good effectiveness, these biobased depressants have the added advantages of being cost effective, biodegradable, non-toxic, and ecofriendly. Nevertheless, further research and investigations are required to improve the selectivity and, consequently, the effectiveness of biobased depressants.

FTIR as a Method for Qualitative Assessment of Solid Samples in Geochemical Research: A Review

This study aims to collect information about soil investigation by FTIR. As we know, the FTIR technique is most often used in organic and bioorganic chemistry, while in geochemistry FTIR spectroscopy is not used very often. Therefore, there is a problem with the identification and interpretation of the IR spectra of minerals contained in sediments and soils. The reason for this is a deficiency of data about characteristic wavenumbers for minerals. Therefore, this study reviews and sums up, in one place, published articles that are connected to an investigation of minerals from 2002 to 2021 (based on the Scopus database). Additionally, the present review highlights various analytical techniques (ATR-FTIR, DRIFT, 2D-IR, and SR-FTIR) and discusses some of them for geochemical study. Additionally, the study describes helpful tools in the data pre-processing of IR spectra (normalization, baseline correction, and spectral derivatives).

Removal performance and mechanism of phosphorus by different Fe-based layered double hydroxides

Phosphorus pollution has the potential to cause both aquatic eutrophication and global phosphorus scarcity. Fe-based layered double hydroxides (LDHs) have received much attention due to their high phosphorus adsorption and recovery. The composition of Fe-based LDHs is an important factor in determining their adsorption performance. However, the mechanism by which single component regulation of Fe-based LDHs affects phosphorus adsorption performance remains unknown. In this study, two typical types of Fe-based LDHs were prepared: Mg/Fe LDH and Zn/Fe LDH. Results showed that the equilibrium adsorption capacity of Zn/Fe LDH was much greater than that of Mg/Fe LDH, reaching 65.85 mg/g with a phosphorus concentration of 150 mg/L. Calcination facilitated a substantial increase of adsorption capacity for Mg/Fe LDH rather than Zn/Fe LDH. Meanwhile, the phosphorus removal efficiency of Fe-based LDHs both exceeded 90% with an initial pH of 3.0, but it decreased as pH increased, and pH inhibition was relatively weaker for Zn/Fe LDH than Mg/Fe LDH. The common coexisting anions caused a phosphorus adsorption loss, with SO₄^2- possessing the most competition with phosphorus. Combined with FTIR, XRD, XPS, and BET analyses, a superior adsorption performance of Zn/Fe-LDH over Mg/Fe-LDH was probably attributed to a higher surface complexation and larger specific surface area. It was also concluded that Fe-based LDHs are a promising method for removing phosphorus from recirculating aquaculture wastewater.

The influence of alkali-modified biochar on the removal and release of Zn in bioretention systems: Adsorption and immobilization mechanism

Generally, Zn in stormwater runoff is considered as low toxicity, but in the senarios of roads and zinc-based materials roof runoff, the concentration of Zn becomes extremely high and cannot be ignored. Bioretention systems are used to remove heavy metals from stormwater runoff, while Zn adsorption is insufficient by conventional filler and is prone to secondary release when exposed to acid rain or high salinity runoff. This study integrated batch experiments and density functional theory calculation to investigate the mechanisms of how KOH-modified biochar (KBC) influences the removal and release of Zn in bioretention systems. The results revealed that KBC adsorbed 89.0-97.5% Zn in the influent, the main adsorption mechanism were complexation and precipitation, and precipitation is more important. In addition, 67% of Zn was immoblized as the residual form by KBC. In acidic and saline runoff, KBC reduced Zn secondary release by 43.6% and 37.08% compared to the results in the absence of KBC, which was attributed to the convertion of most dissolved Zn in acidic and saline runoff into residual Zn. Therefore, KBC has a considerable application potential not only to decontaminate the runoff of roads and Zn-containing roofs, but also to deal with secondary Zn release in acid rain or under the treatment of snow-melting agents.

Synthesis and characterization of a heterogeneous catalyst from a mixture of waste animal teeth and bone for castor seed oil biodiesel production

The present study focused on the synthesis of heterogeneous catalyst from a mixture of waste animal teeth and bone through thermal method. The produced catalyst was used for castor seed oil (CO) biodiesel production. A different mixing ratio of teeth and bone was used with a calcination temperature range from 650 °C to 1250 °C with 100 °C increment for 3h calcination duration. Thermogravimetric analysis (TGA) for animal teeth and bone was performed to identify the common decomposition temperature range. The effect of calcination temperature on basicity of the catalyst and yield of biodiesel was studied for each teeth and bone mixing ratio. Maximum basicity of 6.12mmol HCl/g and biodiesel of 89.5wt% was obtained by mixing ratio of 25wt% teeth and 75wt% bone at calcination temperature of 1150 °C for 3h. The purity of the produced biodiesel in terms of mono fatty acid methyl esters (FAME) formation was found to be 92.6%. X-ray Diffraction (XRD), X-Ray fluorescence (XRF), Fourier-transform infrared spectroscopy (FT-IR) and TGA was used to characterize the raw and produced catalyst. The maximum yield of FAME (89.5wt% with 92.6% purity) was obtained by 5wt% catalyst loading and 9:1 M ratio of methanol to castor seed oil at 60 °C reaction temperature for 3h. Compositional analysis of the produced CO FAME was performed by FT-IR, gas chromatography-mass spectroscopy (GC-MS) and nuclear magnetic resonance (NMR). The performance of the produced catalyst was also checked using its reusability for transesterification CO. Further, the physico-chemical properties including rheological properties of the produced CO FAME were characterized by ASTM methods to check its suitability as a liquid biofuel.

Tannery waste-derived biochar as a carrier of micronutrients essential to plants

The leather tannery industry generates about 33 Mt/year of solid waste with different properties, turning its management into a challenge. One of the valorization methods of tannery wastes is the production of biochar by pyrolysis of leather scratches. Biochar's sorption properties and its high nitrogen content (10%) make it suitable for its application as a soil conditioner or carrier of microelements for fertilizers. The paper presents an innovative spray method to enrich biochar with cationic micronutrients: Cu, Mn, Zn. Enriched biochar contained 1095 mg/kg Cu(II), 1334 mg/kg Mn(II) and 1205 mg/kg Zn(II). The high bioavailability of nutrients and the effectiveness of the new fertilizer were demonstrated in extraction in vitro tests - the analysis of leachability of elements to water and bioavailability of micro-nutrients. The functional properties of enriched biochar were examined in vivo (germination, pot) tests. A high biomass increase (approximately 10%) was observed compared to the group fertilized with a commercial product. The proposed solution benefits the environment in that it is made from alternative resources from which innovative fertilizers are produced according to the circular economy concept.

Highly thermostable white-emitting Ca9ZnK(PO4)7:Ce3+,Dy3+ single-phase phosphor with tunable photoluminescence and energy transfer

White light-emitting diodes (WLEDs) fabricated with single-phase white phosphor are currently widely used in lighting and displays. Herein, we describe the development of a single-component white-emitting micro-sized powder Ca₉ZnK(PO₄)₇ (CZKP):Ce³⁺,Dy³⁺ with high thermal stability. Theoretical and experimental investigations confirmed that the phosphate CZKP with a whitlockite-like structure was suitable as a phosphor host. The photoluminescence of cerium/dysprosium single- and co-doped samples was comprehensively studied. Dipole-dipole interaction resulted in the Ce³⁺ → Dy³⁺ energy transfer, which contributed to the spectral regulation for acquiring the white-emitting performance. Moreover, the superior thermal stability of the representative CZKP:0.10Ce³⁺,0.15Dy³⁺ phosphor was revealed. Finally, we explored the working performance of single-phase white phosphor-converted WLEDs. The corresponding work shows a successful design for achieving a single-component white phosphor via the Ce³⁺ → Dy³⁺ energy transfer approach.

The 'Shellome' of the Crocus Clam Tridacna crocea Emphasizes Essential Components of Mollusk Shell Biomineralization

Molluscan shells are among the most fascinating research objects because of their diverse morphologies and textures. The formation of these delicate biomineralized structures is a matrix-mediated process. A question that arises is what are the essential components required to build these exoskeletons. In order to understand the molecular mechanisms of molluscan shell formation, it is crucial to identify organic macromolecules in different shells from diverse taxa. In the case of bivalves, however, taxon sampling in previous shell proteomics studies are focused predominantly on representatives of the class Pteriomorphia such as pearl oysters, edible oysters and mussels. In this study, we have characterized the shell organic matrix from the crocus clam, Tridacna crocea, (Heterodonta) using various biochemical techniques, including SDS-PAGE, FT-IR, monosaccharide analysis, and enzyme-linked lectin assay (ELLA). Furthermore, we have identified a number of shell matrix proteins (SMPs) using a comprehensive proteomics approach combined to RNA-seq. The biochemical studies confirmed the presence of proteins, polysaccharides, and sulfates in the T. crocea shell organic matrix. Proteomics analysis revealed that the majority of the T. crocea SMPs are novel and dissimilar to known SMPs identified from the other bivalve species. Meanwhile, the SMP repertoire of the crocus clam also includes proteins with conserved functional domains such as chitin-binding domain, VWA domain, and protease inhibitor domain. We also identified BMSP (Blue Mussel Shell Protein, originally reported from Mytilus), which is widely distributed among molluscan shell matrix proteins. Tridacna SMPs also include low-complexity regions (LCRs) that are absent in the other molluscan genomes, indicating that these genes may have evolved in specific lineage. These results highlight the diversity of the organic molecules – in particular proteins – that are essential for molluscan shell formation.