Adsorption studies of methylene blue and lead ions from aqueous solution by using mesoporous coral limestones

Effect of citric acid modification on the properties of hydrochar and pyrochar and their adsorption performance toward methylene blue: crucial roles of minerals and oxygen functional groups

Modification is widely used to enhance the adsorption performance of pristine hydrochar (HBC) and pyrochar (BC). However, comparisons between modified HBC and BC toward pollutant removal have rarely been reported. In this study, pristine HBC and BC derived from rice straw were first produced, and then citric acid (CA) was used as a modifier to synthesize CA-modified HBC (CAHBC) and CA-modified BC (CABC). Furthermore, the adsorption performance of biochars toward methylene blue (MB) was investigated. The results showed that BC exhibits relatively rough surfaces and contains more minerals (ash), whereas HBC has plentiful O-containing functional groups and fewer minerals. CA modification partially removed minerals from the surface of BC, which weakened the ion exchange, surface complexation, and n-π interaction, resulting in a lower adsorption ability toward MB. By contrast, CA produced more O-containing functional groups on the surface of HBC, which strengthened the hydrogen bonding and electrostatic interaction, thus increasing the adsorption capacity toward MB. The two-compartment model showed a good fit to the adsorption process of MB on CAHBC, and the isotherm data for MB adsorption by HBC and CAHBC are suitable for the Freundlich model. The highest adsorption amount of MB using CAHBC was 80.13 mg·g-1, which was 27.66% higher than that for CABC. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy analysis indicated that the carboxyl groups in the surface functional groups of CAHBC played a crucial role in the MB adsorption process. In addition, CAHBC showed a good performance for a wide range of pH values (4.0-10.0) and under the interference of coexisting ions, and also presented a recycling ability. Furthermore, the adsorption of MB on CAHBC biochar was a spontaneous, exothermic, degree-of-randomness-increasing process. Consequently, CA modification of HBC is a promising strategy and could be used for MB removal from aquatic environments.

Synthesis of a novel multifunctional organic-inorganic nanocomposite for metal ions and organic dye removals

In this study, we used solvent assisted mechano-synthesis strategies to form multifunctional organic-inorganic nanocomposites capable of removing both organic and inorganic contaminants. A zeolite X (Ze) and activated carbon (AC) composite was synthesized via state-of-the-art mechanical mixing in the presence of few drops of water to form Ze/AC. The second composite (Ze/L/AC) was synthesized in a similar fashion, however this composite had the addition of disodium terephthalate as a linker. Both materials, Ze/AC and Ze/L/AC, were characterized using scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS), Powdered X-ray diffraction (P-XRD), Fourier-transform infrared spectrometry (FTIR), Accelerated Surface Area and Porosimetry System (ASAP), and thermal gravimetric analysis (TGA). The SEM-EDS displayed the surface structure and composition of each material. The sodium, oxygen and carbon contents increased after linker connected Ze and AC. The P-XRD confirmed the crystallinity of each material as well as the composites, while FTIR indicated the function groups (C=C, O-H) in Ze/L/AC. The contaminant adsorption experiments investigated the effects of pH, temperature, and ionic strength on the adsorption of methylene blue (MB) and Co(II) for each material. In MB adsorption, the first-order reaction rate of Ze/L/AC (0.02 h-1) was double that of Ze/AC (0.01 h-1). The reaction rate of Ze/L/AC (4.8 h-1) was also extraordinarily higher than that of Ze/AC (0.6 h-1) in the adsorption of Co(II). Ze/L/AC composite achieved a maximum adsorption capacity of 44.8 mg/g for MB and 66.6 mg/g for Co(II) ions. The MB adsorption of Ze/AC and Ze/L/AC was best fit in Freundlich model with R2 of 0.96 and 0.97, respectively, which indicated the multilayer adsorption. In the Co(II) adsorption, the data was highly fit in Langmuir model with R2 of 0.94 and 0.92 which indicated the monolayer adsorption. These results indicated both materials exhibited chemisorption. The activation energy of Ze/L/AC in MB adsorption (34.9 kJ mol-1) was higher than that of Ze/L/AC in Co (II) adsorption (26 kJ mol-1).

Removal of methylene blue dye from aqueous solution using an efficient chitosan-pectin bio-adsorbent: kinetics and isotherm studies

Wastewater contains organic compounds, including dyes, which have potential risks to the environment. Hence, these compound needs to be eliminated from the aqueous solution. In the present study, chitosan-pectin composite (Cs-Pc) was used as an adsorbent to remove methylene blue dye (MB) from synthetic wastewater. To evaluate the parameters affecting adsorption, including the initial MB concentration, solution pH, contact time, and Cs-Pc dose, batch experiments were carried out. Scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), Fourier transform infrared (FTIR), and pH point of zero charges (pH pzc) were applied for characterizations of Cs-Pc. The optimum conditions were obtained with an initial MB concentration of 50 mg L^-1: solution pH ~ 11, Cs-Pc dose: 1.5 g L^-1 and 180 min contact time, which caused 97.77% of MB removal. In addition, the removal efficiency of MB was more influenced by pH than by sorbate dose. Also, Cs-Pc had a higher ability to remove MB than chitosan and pectin, probably due to its highly porous structure and rough surfaces that provides active sites and facilitate MB adsorption. The maximum removal efficiency and the adsorption capacity of MB onto Cs-Pc at 500 mg L^-1 concentration under optimum conditions were 98.67% and 328.02 mg g^-1, respectively. The adsorption kinetics and isotherms were best described by pseudo-second-order and Freundlich equation, respectively. After four times of recycling, the removal efficiency of MB was above 96%. Electrostatic and pi-pi interactions are the main mechanisms for the removal of MB onto the adsorbent. So the application of Cs-Pc is promising for MB removal from polluted solutions not only due to its strong adsorbing capability but also due to its excellent ability to reuse.

The Adsorption of Copper, Lead Metal Ions, and Methylene Blue Dye from Aqueous Solution by Pure and Treated Fennel Seeds

This research work reports on pure and acid-treated fennel seed biomaterials for the removal of metal ions of copper Cu(II), lead Pb(II), and methylene blue (MB) dye from aqueous solution by batch adsorption. Pure fennel seeds were labelled as PFS; nitric and sulphuric acid-treated seeds were designated as NAFS and SAFS, respectively. The adsorbents were characterised by SEM, EDX, FTIR, XRD, and BET. The SEM images revealed that the surface of the adsorbents was porous. However, physicochemical characterization further revealed that BET surface area, pore size, and pore width increased for NAFS and SAFS compared to PFS. FTIR results revealed that the peaks for cellulose −COC and −OH decreased considerably for NAFS and SAFS; this indicated that cellulose was hydrolyzed during acid treatment. Adsorption data showed that all biomaterials had a higher affinity for MB dye more than Pb(II) and Cu(II) metal ions. The maximum adsorption capacities onto PFS were 6.834, 4.179, and 2.902 mg/g and onto NAFS are 15.28, 14.44, and 4.475 mg/g, while those onto SAFS are 19.81, 18.79 and 6.707 mg/g respective for MB dye, Pb(II), and Cu(II) ions. Postadsorption analysis revealed that adsorption of Pb(II) and Cu(II) was controlled mainly by the electrostatic attraction, while that of MB was synergistic of electrostatic attraction, π-π interaction, and hydrogen bond. It was found that the uptake processes of MB dye onto all adsorbents fitted Freundlich while both cations were described by Langmuir model. The thermodynamic parameters $\Delta H$ o and $\Delta G$ o indicated the endothermic nature and spontaneity of the processes, respectively.

Equilibrium and Kinetic Study of Anionic and Cationic Pollutants Remediation by Limestone-Chitosan-Alginate Nanocomposite from Aqueous Solution

In this work, low-cost and readily available limestone was converted into nanolimestone chitosan and mixed with alginate powder and precipitate to form a triple nanocomposite, namely limestone—chitosan–alginate (NLS/Cs/Alg.), which was used as an adsorbent for the removal of brilliant green (BG) and Congo red (CR) dyes in aqueous solutions. The adsorption studies were conducted under varying parameters, including contact time, temperature, concentration, and pH. The NLS/Cs/Alg. was characterized by SEM, FTIR, BET, and TEM techniques. The SEM images revealed that the NLS/Cs/Alg. surface structure had interconnected pores, which could easily trap the pollutants. The BET analysis established the surface area to be 20.45 m²/g. The recorded maximum experimental adsorption capacities were 2250 and 2020 mg/g for CR and BG, respectively. The adsorption processes had a good fit to the kinetic pseudo second order, which suggests that the removal mechanism was controlled by physical adsorption. The CR and BG equilibrium data had a good fit for the Freundlich isotherm, suggesting that adsorption processes occurred on the heterogeneous surface with a multilayer formation on the NLS/Cs/Alg. at equilibrium. The enthalpy change (ΔH⁰) was 37.7 KJ mol⁻¹ for CR and 8.71 KJ mol⁻¹ for BG, while the entropy change (ΔS⁰) was 89.1 J K⁻¹ mol⁻¹ for CR and 79.1 J K⁻¹ mol⁻¹ BG, indicating that the adsorption process was endothermic and spontaneous in nature.