Innovative operation of microbial fuel cell-based biosensor for selective monitoring of acetate during anaerobic digestion

Assessment of the microbial electrochemical sensor (SENTRY™) as a potential wastewater quality monitoring tool for common pollutants found in Malaysia

Bioelectrochemical sensors for environment monitoring have the potential to provide facility operators with real-time data, allowing for better and more timely decision-making regarding water and wastewater treatment. To assess the robustness and sensitivity of the Sentry™ biosensor in local conditions, it was tested in Malaysia using domestically available wastewater. The study objectives included (1) enrich the biosensor locally, (2) operate and test the biosensor with local domestic wastewater, and (3) determine the biosensor's responsiveness to model pollutants through pollutant spike and immersion test as well as response to absence of wastewater. Lab-scale operation shows the biosensor was successfully enriched with (1) local University Kebangsaan Malaysia's, microbial community strain collection and (2) local municipal wastewater microflora, operated for more than 50 days with a stable yet responsive carbon consumption rate (CCR) signal. Meanwhile, two independent biosensors were also enriched and operated in Indah Water Research Centre's crude sewage holding tank, showing a stable response to the wastewater. Next, a pilot scale setup was constructed to test the enriched biosensors for the spiked-pollutant test. The biosensors showed a proportional CCR response (pollutant presence detected) towards several organic compounds in the sewage, including ethanol, chicken blood, and dilution of tested sewage but less to curry powder, methanol, and isopropanol. Conversely, there was no significant response (pollutant presence not detected) towards hexane, Congo red, engine oil, and paint, which may be due to their non-biodegradability and/or insoluble nature. Additionally, the biosensors were exposed to air for 6 h to assess their robustness towards aerobic shock with a positive result. Overall, the study suggested that the biosensor could be a powerful monitoring tool, given its responsiveness towards organic compounds in sewage under normal conditions.

Recent progress in the characterization and application of exo-electrogenic microorganisms

Exo-electrogenic microorganisms are characterized by their special metabolic capability of transferring metabolic electrons out of their cell, into insoluble external electron acceptors such as iron or manganese oxides and electrodes, or vice versa take up electron from electrodes. Their conventional application is primarily limited to microbial fuel cells for electrical power generation and microbial electrolysis cells for the production of value-added products such as biohydrogen, biomethane and hydrogen peroxide. The utility of exo-electrogenic organisms has expanded into many other applications in recent times. Such examples include microbial desalination cells, microbial electro-synthesis cells producing value-added chemicals such as bio-butanol and their applications in other carbon sequestration technologies. Additionally, electrochemically-active organisms are now beginning to be employed in biosensor applications for environmental monitoring. Additionally, the utility of biocathodes in bio-electrochemical systems is also a novel application in catalyzing the cathodic oxygen reduction reaction to enhance their electrochemical performance. Advances have also been made in the expansion and use of other organisms such as the usage of photosynthetic microorganisms for the fabrication of self-sustained bio-electrochemical systems. This review attempts to provide a comprehensive picture of the state-of the art of exo-electrogenic organisms and their novel utility in bioelectrochemical systems.

The versatility of microbial fuel cells as tools for organic matter monitoring

Water monitoring and remediation require robust, low-cost, and reliable test systems that can couple with prompt treatment interventions. Organic matter (BOD, COD), toxicants, heavy metals, and other pollutants in water need to be regularly inspected. Microbial fuel cells (MFCs) have already gained popularity as BOD biomonitoring systems as these don't need an external transducer or power source. Moreover, these systems are cost-effective, compact, biodegradable, reusable, portable, and applicable for on-site measurements. MFCs truly stands out as online BOD measurement devices as they provide wide detection range (0-25 g/L), low response time (2-4 min) and longer stability in continuous operations (2-5 years) in a cost-effective approach. This review examines the benefits, kinds, performance metrics, and signal optimization of the current state-of-the-art of the BOD measurement, with detailed focus on MFC-based BOD biomonitoring systems. This review covers the important technological breakthroughs in practical applications with associated bottlenecks to develop reliable sensing systems.

Recent Implementations of Hydrogel-Based Microbial Electrochemical Technologies (METs) in Sensing Applications

Hydrogel materials have been used extensively in microbial electrochemical technology (MET) and sensor development due to their high biocompatibility and low toxicity. With an increasing demand for sensors across different sectors, it is crucial to understand the current state within the sectors of hydrogel METs and sensors. Surprisingly, a systematic review examining the application of hydrogel-based METs to sensor technologies has not yet been conducted. This review aimed to identify the current research progress surrounding the incorporation of hydrogels within METs and sensors development, with a specific focus on microbial fuel cells (MFCs) and microbial electrolysis cells (MECs). The manufacturing process/cost, operational performance, analysis accuracy and stability of typical hydrogel materials in METs and sensors were summarised and analysed. The current challenges facing the technology as well as potential direction for future research were also discussed. This review will substantially promote the understanding of hydrogel materials used in METs and benefit the development of electrochemical biosensors using hydrogel-based METs.

Solid slow-release carbon source assembled microbial fuel cell for promoting superior nitrogen removal in an aerobic granular sludge bioreactor

Although the coupling process of microbial fuel cell (MFC) and activated sludge is widely used for organic matter removal and electric energy recovery, the problem of high effluent nitrate still exists due to the lack of influent carbon source. Herein, a poly (butanediol succinate) (PBS) assembled MFC was established in an aerobic granular sludge (AGS) bioreactor for simultaneous promoting nitrogen removal and electricity generation. Compared to AGS-Control group, the total inorganic nitrogen (TIN) and COD removal efficiencies of AGS-MFC group were improved to 84.3 ± 2.6% and 93.5 ± 0.5% after 100-days operation. The average output voltage and the maximum power density of the MFC module were 223.7 mV and 59.6 mW/m², respectively. Through high-throughput sequencing analysis, Thauera-related denitrifying bacteria had the highest relative abundances (20.0% and 31.4%) in both bioreactors. The relative abundance of Nitrosomonas-related ammonia oxidizing bacteria (AOB) in AGS-MFC (1.8%) was enriched than AGS-Control (1.1%). In MFC module, Thauera (16.2%) with denitrification and power generation was dominant in anodic biofilms under PBS enhancement. This study provides scientific basis for the application of submersible MFC enhanced deep nitrogen removal under aerobic conditions.

A Review of Recent Advances in Microbial Fuel Cells: Preparation, Operation, and Application

The microbial fuel cell has been considered a promising alternative to traditional fossil energy. It has great potential in energy production, waste management, and biomass valorization. However, it has several technical issues, such as low power generation efficiency and operational stability. These issues limit the scale-up and commercialization of MFC systems. This review presents the latest progress in microbial community selection and genetic engineering techniques for enhancing microbial electricity production. The summary of substrate selection covers defined substrates and some inexpensive complex substrates, such as wastewater and lignocellulosic biomass materials. In addition, it also includes electrode modification, electron transfer mediator selection, and optimization of operating conditions. The applications of MFC systems introduced in this review involve wastewater treatment, production of value-added products, and biosensors. This review focuses on the crucial process of microbial fuel cells from preparation to application and provides an outlook for their future development.

Glucose Fuel Cells and Membranes: A Brief Overview and Literature Analysis

Glucose is a ubiquitous source of energy for nearly all living things, and glucose fuel cells (GFCs) are regarded as a sustainable power source because glucose is renewable, easily available, cheap, abundant, non-toxic and easy-to-store. Numerous efforts have been devoted to developing and improving GFC performance; however, there is still no commercially viable devices on the market. Membranes play an essential role in GFCs for the establishment of a suitable local microenvironment, selective ion conducting and prevention of substrate crossover. However, our knowledge on them is still limited, especially on how to achieve comparable efficacy with that of a biological system. This review article provides the first brief overview on these aspects, particularly keeping in sight the research trends, current challenges, and the future prospects. We aim to bring together literature analysis and technological discussion on GFCs and membranes by using bibliometrics, and provide new ideas for researchers in this field to overcome challenges on developing high-performance GFCs.

Review on microbial fuel cells applications, developments and costs

The microbial fuel cell (MFC) technology has attracted significant attention in the last years due to its potential to recover energy in a wastewater treatment. The idea of using an MFC in industry is very attractive as the organic wastes can be converted into energy, reducing the waste disposal costs and the energy needs while increasing the company profit. However, taking aside these promising prospects, the attempts to apply MFCs in large-scale have not been succeeded so far since their lower performance and high costs remains challenging. This review intends to present the main applications of the MFC systems and its developments, particularly the advances on configuration and operating conditions. The diagnostic techniques used to evaluate the MFC performance as well as the different modeling approaches are described. Towards the introduction of the MFC in the market, a cost analysis is also included. The development of low-cost materials and more efficient systems, with high higher power outputs and durability, are crucial towards the application of MFCs in industrial/large scale. This work is a helpful tool for discovering new operation and design regimes.

Exopolysaccharides matrix affects the process of extracellular electron transfer in electroactive biofilm

The applications of bioelectrochemical systems (BESs) in the field of environment and energy are achieved through the bioelectrocatalytic process of electroactive biofilms. As a primary component of biofilm, the role of exopolysaccharides in electroactive biofilm in BESs is poorly understood. This study constructed an exopolysaccharides-deficient Geobacter sulfurreducens-based BES to explore the role of exopolysaccharides in electroactive biofilm. Compared with the wild type, the mutant biofilm expressing less exopolysaccharides decreased the capacity of current generation. In the mutant biofilm, the content of exopolysaccharides decreased significantly, resulting in a thinner biofilm and lower cell viability compared with the wild-type biofilm. However, the mutant with overexpressed pili developed a mature biofilm with extended time, which indicating the importance of exopolysaccharides for early biofilm formation and the compensatory role of pili in biofilm formation. The mutant biofilm had less content of c-type cytochromes (c-Cyts) and lower electrochemical activity of extracellular polymeric substances than the wild-type biofilm, suggesting a function of exopolysaccharides anchoring extracellular c-Cyts that essential to extracellular electron transfer (EET) in electroactive biofilms. Our findings demonstrated the essential role of exopolysaccharides in the process of EET in electroactive biofilm, which contributed to a better understanding and optimization of the performance of BESs.

Recent developments in monitoring technology for anaerobic digesters: A focus on bio-electrochemical systems

With the increasing popularity of waste to energy conversion, demand for large-scale operation of anaerobic digestors has emerged in the market. However, the process instabilities in anaerobic digestors limit the expansion of facilities to high loading rates. The irregularities in the process can be addressed directly by altering the feedstock characteristics provided an on-hand, robust, and sensitive monitoring device is available. In this context, the bioelectrochemical system has emerged as an excellent tool for monitoring and optimizing the anaerobic process within the reactor. This article reviews the gradual evolution in techniques and approaches for monitoring of anaerobic digestion (AD) process. An analysis of the recently popular biosensing techniques has been done with a focus on the bioelectrochemical monitoring system and its operation mode. A brief attempt to highlight the current challenges in the field of bioelectrochemical process monitoring for AD has also been made, which can be supportive of future research.

Innovative air-cathode bioelectrochemical sensor for monitoring of total volatile fatty acids during anaerobic digestion

Bioelectrochemical sensors have proven attractive as simple and low-cost methods with high potential for online monitoring of volatile fatty acids (VFA) in the anaerobic digestion (AD) process. Herein, an innovative dual-chamber air-cathode microbial fuel cell was developed as biosensor for VFA monitoring. The response of the biosensor was nonlinear and increased along with the concentration of VFA mixture increase (2.8-112 mM). Meanwhile, the relationship was linear with low VFA levels (<14 mM) within 2-5 h reaction. High concentrations of bicarbonate decreased the voltage. Stirring speeded up the response and amplified the signal but reduced the saturation concentration (approximately 30 mM) and therefore narrowed the detection range. The applicability of the biosensor was further validated with the effluents from an AD reactor during a start-up period. The VFA concentrations measured by the biosensor were well correlated with the gas chromatographic measurement. The results demonstrate that this biosensor with a novel design could be used for VFA monitoring during the AD process. Based on the 16S rRNA gene sequencing, the dominant microbiomes in the biofilm were identified as Geobacter, Hydrogenophaga, Pelobacter, Chryseobacterium, Oryzomicrobium, and Dysgonomonas.

Hibernations of electroactive bacteria provide insights into the flexible and robust BOD detection using microbial fuel cell-based biosensors

Microbial fuel cell (MFC) biosensors have been suggested as an alternative detection method for biochemical oxygen demand (BOD). However, it is absolutely essential to develop maintenance procedures for MFC biosensors` because in practice the lay-up period cannot be avoided. In this work, setting electroactive bacteria (EAB) under hibernation condition was demonstrated to be a feasible maintenance method, which provided important insights into the flexible and robust BOD detection using MFC biosensors. Standard BOD solution containing 500, 200, and 20 mg/L BOD were used to evaluate the detection performance after EAB hibernations. Results demonstrated quick recovery of voltage output and high-accuracy BOD detection after hibernations up to 30 days in MFC biosensors detecting 500 mg/L and 200 mg/L BOD. Identical anode potentials after the EAB hibernations suggested intact bacterial ability of current generation. Non-turnover cyclic voltammetry immediately collected after the hibernations suggested multiple redox couples and the presence of cytochromes that played key roles in EAB metabolism and functioned as temporary electron sinks during the hibernations, leading to the increased detected BOD concentration in the restarting cycles. Generally, setting EAB under hibernation condition is a simple and convenient maintenance method for MFC-based BOD biosensors, which not only provides insights into flexible and robust BOD detection, but also be helpful for other MFC biosensing instruments.

Physiological potential of extracellular polysaccharide in promoting Geobacter biofilm formation and extracellular electron transfer

Geobacter sulfurreducens biofilms have promising applications in renewable energy, pollutant bioremediation, and bioelectronic applications. Genetically manipulating G. sulfurreducens biofilms is an effective strategy to improve the capacity of extracellular electron transfer (EET). Extracellular polysaccharide, a sticky component surrounding microbes, plays an important role in EET. Herein, we constructed a mutant of G. sulfurreducens strain PCA overexpressing the gene GSU1501 (part of the ATP-dependent exporter of the polysaccharide biosynthesis gene operon), designated strain PCA-1501, to increase EET capacity. Experimental results showed that the overexpression of GSU1501 increased extracellular polysaccharide secretion by 25.5%, which promoted the formation of biofilm with higher thickness and viability, as well as the content of extracellular c-type cytochromes. Compared with the control strain, the mutant showed a higher capacity of Fe(III) oxide reduction and current generation (increased by 20.4% and 22.2%, respectively). Interestingly, the overexpression of GSU1501 hindered the pili formation by reducing the transcription level of pilA; a compensatory relationship between extracellular polysaccharide and pili in promoting biofilm formation deserves further investigation. This study provides a feasible method to promote the EET capacity of G. sulfurreducens biofilms, which benefit their bioelectrochemical applications.

A quick start method for microbial fuel cells

Microbial fuel cells (MFCs) have great potential to detect toxicity early. Study of toxicity sensors based on MFCs requires a large number of stable MFCs. However, the start-up time of MFCs is generally long, which limits research progress. In this study, a first-stage preculture based on H-type MFCs (first culture) and a second-stage preculture based on multistage MFC reactor series culture (second culture) were used in combination with preculture MFCs. The goal of obtaining an MFC with stable performance in only one day was achieved. The obtained MFC could be stable for 33 h and rapidly regenerated with replacement of the anode substrate. The start-up time was shortened because after the first culture and the secondary culture, the protein content attached to the electrode reached 1.2864 ± 0.0174 mg/cm² and 2.22 ± 0.12 mg/cm², respectively. Bacteria that generate electricity, such as Geobacter, were effectively enriched. This study may improve the development efficiency of MFC toxicity sensors.

Carbon nanomaterial-modified graphite felt as an anode enhanced the power production and polycyclic aromatic hydrocarbon removal in sediment microbial fuel cells

Sediment microbial fuel cells (SMFCs) can be used to generate electricity and remove organic contaminants. For electricity generation and contaminant removal, the anode material is one of important factors influencing the performance of SMFCs. In this study, graphene (GR), graphene oxide (GO) and carbon nanotubes (CNTs) were applied to modify the graphite felt (GF) anode in SMFCs during 110 d operation. An economical and easy modification method with the carbon nanomaterials was applied. The carbon nanomaterials increased the electrochemically active surface areas and biomass content of the anodes and correspondingly effectively enhanced the generation of electricity and the removal rates of loss on ignition (LOI) and polycyclic aromatic hydrocarbons (phenanthrene and pyrene). During the steady period from 50 d to 110 d, the GO-SMFCs favored the enrichment of EAB and thus output the highest voltages of 30.60-48.61 mV. The GR-SMFCs and GO-SMFCs generated high electric power of approximate 0.98 ± 0.14 kJ and 0.87 ± 0.04 kJ, followed by CNT-SMFCs (0.57 ± 0.06 kJ) and GF-SMFCs (0.49 ± 0.07 kJ) during the 110 d operation. The PAH degradation was not directly related to the electric current in the SMFCs. Near the anodes, the order of the phenanthrene removal rates was CNT-SMFCs (78.1%) > GR-SMFCs (73.0%) ≈ GO-SMFCs (71.2%) > GF-SMFCs (45.6%), and the order of the pyrene removal rates was GO-SMFCs (69.6%) ≈ GR-SMFCs (68.2%) ≈ CNT-SMFCs (66.7%) > GF-SMFCs (42.3%). The three carbon nanomaterials increased the microbial community diversity and slightly changed the microbial community distribution of biofilms on the anodes. Correlation analysis indicated that the degradation of phenanthrene was positively correlated with the abundances of Pseudomonas, Thauera, Diaphorobacter, Tumebacillus and Lysobacter. Pyrene degradation was strongly correlated with LOI degradation.

Scratching and transplanting of electro-active biofilm in fruit peeling leachate by ultrasound: re-inoculation in new microbial fuel cell for enhancement of bio-energy production and organic matter detection

OBJECTIVE

An electro-active biofilm of Fruit Peeling (FP) leachate was formed onto the Carbon Felt (CF) bio-anode in a Microbial Fuel Cell (MFC), after functioning for a long time. The electro active-biofilm thus formed was then scratched by ultrasound and re-inoculated in a new leachate to be transplanted onto the bio-anode. This procedure allowed the microbial electron charge transfer and therefore the enhancement of the bio-energy production of the fuel cell.

RESULTS

By using the repetitive mechanical biofilm removal, re-suspension and electrochemically facilitated biofilm formation, the voltage was substantially increased. In effect, the voltage of the 1st G of biofilm, rose gradually and reached its maximum value of 65 mV after 10 days. Whilst the 2nd generation allowed to obtain the maximum voltage 276 mV and without any lag time. The DCO abatement using the 1st G biofilm was 68% greater than the 3rd G 26%. Besides, the electrochemical impedance spectroscopy characterization and cyclic voltammetry of bio-anode with 2nd G biofilm confirmed the ability of electro-active biofilm formation on a new support. The biofilm transplanted showed thus greater kinetic performance, with reduced lag time demonstrating the interest of the selection that took place during the formation of successive biofilms.

CONCLUSIONS

Despite the transplantation of the electro-active biofilm onto the bio-anode, the MFC still produced relatively lower power output. Nevertheless, it has been tested successfully for monitoring and detecting the oxidation of sodium acetate substrate in the very wide concentration range 0.0025-35 g/l.

A sensitive, wide-ranging comprehensive toxicity indicator based on microbial fuel cell

An innovative indicator for toxicity detection based on microbial fuel cells, average current inhibition rate (ACIR) was proposed. It was applied to the toxicity evaluation of three typical specific pollutants in petrochemical wastewater including copper(II), 2,4-dichlorophenol (2,4-DCP) and pyridine. ACIR which considered the entire process of toxic effects was proved to be more sensitive and wide-ranging than the conventional indicators. The linear detection ranges were 0.3-100 mg/L of copper(II), 0.4-1000 mg/L of 2,4-DCP, and 0.1-1000 mg/L of pyridine. The median effective concentrations of the three toxicants were 34.32, 36.18 and above 1000 mg/L, respectively. By contrast, using a conventional indicator such as the voltage inhibition rate, the calculation results consistently change with the exposure time. Based on the response time, the toxicity will be difficult to distinguish under high concentrations. An analysis of the microbial community in anode chamber showed that electrogenic bacteria such as Geobacter and Arcobacter significantly decreased with 2,4-DCP and pyridine under all tested concentrations. A principal component analysis was conducted, the results of which showed that the microbial community shifted from left to right with the increase concentration of copper(II) and 2,4-DCP. An increase of ACIR was noticed to be in accordance with the reduction of electrogenic bacteria.

Biosensing capabilities of bioelectrochemical systems towards sustainable water streams: Technological implications and future prospects

Bioelectrochemical systems (BESs) have been intensively investigated over the last decade owing to its wide-scale environmentally friendly applications, among which wastewater treatment, power generation and environmental monitoring for pollutants are prominent. Different variants of BES such as microbial fuel cell, microbial electrolysis cell, microbial desalination cell, enzymatic fuel cell, microbial solar cell, have been studied. These microbial bioelectrocatalytic systems have clear advantages over the existing analytical techniques for sustainable on-site application in wide environmental conditions with minimum human intervention, making the technology irrevocable and economically feasible. The key challenges to establish this technology are to achieve stable and efficient interaction between the electrode surface and microorganisms, reduction of time for start-up and toxic-shock recovery, sensitivity improvement in real-time conditions, device miniaturization and its long-term economically feasible commercial application. This review article summarizes the recent technical progress regarding bio-electrocatalytic processes and the implementation of BESs as a biosensor for determining various compositional characteristics of water and wastewater.

Microbial Fuel Cell-Based Biosensors

The microbial fuel cell (MFC) is a promising environmental biotechnology that has been proposed mainly for power production and wastewater treatment. Though small power output constrains its application for directly operating most electrical devices, great progress in its chemical, electrochemical, and microbiological aspects has expanded the applications of MFCs into other areas such as the generation of chemicals (e.g., formate or methane), bioremediation of contaminated soils, water desalination, and biosensors. In recent decades, MFC-based biosensors have drawn increasing attention because of their simplicity and sustainability, with applications ranging from the monitoring of water quality (e.g., biochemical oxygen demand (BOD), toxicants) to the detection of air quality (e.g., carbon monoxide, formaldehyde). In this review, we summarize the status quo of MFC-based biosensors, putting emphasis on BOD and toxicity detection. Furthermore, this review covers other applications of MFC-based biosensors, such as DO and microbial activity. Further, challenges and prospects of MFC-based biosensors are briefly discussed.

Microbial Fuel Cell-Based Biosensors

The microbial fuel cell (MFC) is a promising environmental biotechnology that has been proposed mainly for power production and wastewater treatment. Though small power output constrains its application for directly operating most electrical devices, great progress in its chemical, electrochemical, and microbiological aspects has expanded the applications of MFCs into other areas such as the generation of chemicals (e.g., formate or methane), bioremediation of contaminated soils, water desalination, and biosensors. In recent decades, MFC-based biosensors have drawn increasing attention because of their simplicity and sustainability, with applications ranging from the monitoring of water quality (e.g., biochemical oxygen demand (BOD), toxicants) to the detection of air quality (e.g., carbon monoxide, formaldehyde). In this review, we summarize the status quo of MFC-based biosensors, putting emphasis on BOD and toxicity detection. Furthermore, this review covers other applications of MFC-based biosensors, such as DO and microbial activity. Further, challenges and prospects of MFC-based biosensors are briefly discussed.